Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM(w/ Retract Mirror) › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052853 MIRROR (EXT) _0255766 POWER MIRROR CONTROL SYSTEM(w/ Retract Mirror) J

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM(w/ Retract Mirror)  Front Passenger Side Power Mirror cannot be Adjusted with Power Mirror Switch  


SYSTEM DESCRIPTION

The circuit detects the conditions of the outer mirror switch.

The outer mirror switch sends information about the operating condition of the mirror switch (switch input signals) through the CAN communication line. Then the switch input signals are sent to the outer mirror control ECU. Mirror adjustment is controlled by the outer mirror control ECU.

WIRING DIAGRAM

B182636E40
0.896,2.177 1.292,2.365 0.396,0.188 10 false MSW 1.042,0.906 1.313,1.115 0.271,0.208 10 false M+ 1.135,3.5 1.323,3.698 0.188,0.198 10 false E 0.323,4.073 0.5,4.292 0.177,0.219 10 false G1 3.938,4.052 4.24,4.313 0.302,0.26 10 false I18 1.354,3.385 1.583,3.615 0.229,0.229 10 false 9 1.354,2.073 1.583,2.292 0.229,0.219 10 false 8 1.354,0.792 1.5,1.031 0.146,0.24 10 false 7 2,3.344 2.25,3.552 0.25,0.208 10 false 2 1.969,2.01 2.25,2.198 0.281,0.188 10 false 12 1.958,0.719 2.229,0.938 0.271,0.219 10 false 11 0.302,4.219 1.563,4.604 1.26,0.385 10 false Outer Mirror Switch Assembly 1.958,0.906 2.125,1.115 0.167,0.208 10 false E1 2.26,3.521 2.698,3.729 0.438,0.208 10 false MIRE 2.26,2.198 2.698,2.406 0.438,0.208 10 false MIRS 2.26,0.917 2.698,1.125 0.438,0.208 10 false MIRB 2.125,4.073 3.333,4.729 1.208,0.656 10 false Main Body ECU (Cowl Side Junction Block LH) 3.927,4.229 5.531,4.854 1.604,0.625 10 false Outer Mirror Control ECU 5.75,4.271 7.083,4.865 1.333,0.594 10 false Outer Rear View Mirror Assembly RH 2.688,2.646 3.177,2.875 0.49,0.229 10 false CANN 2.688,1.656 3.094,1.802 0.406,0.146 10 false CANP 4.104,2.667 4.583,2.896 0.479,0.229 10 false CANL 4.115,1.677 4.51,1.917 0.396,0.24 10 false CANH 3.167,2.479 3.406,2.708 0.24,0.229 10 false 15 3.177,1.479 3.417,1.698 0.24,0.219 10 false 16 3.854,2.49 4.156,2.698 0.302,0.208 10 false 21 3.917,1.5 4.156,1.677 0.24,0.177 10 false 1 4.833,2.208 5.198,2.438 0.365,0.229 10 false M+R 4.813,0.885 5.177,1.052 0.365,0.167 10 false MHR 4.833,3.49 5.198,3.698 0.365,0.208 10 false MVR 5.844,2.219 6.125,2.396 0.281,0.177 10 false M+ 5.833,0.896 6.167,1.146 0.333,0.25 10 false MH 5.844,3.5 6.125,3.677 0.281,0.177 10 false MV 5.635,3.375 5.896,3.604 0.26,0.229 10 false 7 5.635,2.094 5.896,2.271 0.26,0.177 10 false 8 5.635,0.771 5.896,0.948 0.26,0.177 10 false 9 5.208,3.385 5.49,3.615 0.281,0.229 10 false 40 5.219,2.094 5.479,2.26 0.26,0.167 10 false 38 5.219,0.771 5.417,0.948 0.198,0.177 10 false 39 0.854,5.313 2.969,5.563 2.115,0.25 10 false : CAN Communication Line 0.104,0.104 1.573,0.344 1.469,0.24 12 false for LHD: 1.969,2.177 2.135,2.385 0.167,0.208 10 false E1 1.969,3.5 2.135,3.708 0.167,0.208 10 false E1 3.177,1.646 3.344,1.854 0.167,0.208 10 false E3 3.177,2.635 3.344,2.844 0.167,0.208 10 false E3 5.75,4.083 6.052,4.344 0.302,0.26 10 false I32

B182636E41
0.896,2.167 1.292,2.354 0.396,0.188 10 false MSW 1.042,0.906 1.313,1.115 0.271,0.208 10 false M+ 1.115,3.49 1.385,3.688 0.271,0.198 10 false E 0.229,4.073 0.458,4.292 0.229,0.219 10 false G1 3.844,4.083 4.042,4.271 0.198,0.188 10 false I24 1.354,3.396 1.583,3.625 0.229,0.229 10 false 9 1.354,2.083 1.583,2.302 0.229,0.219 10 false 8 1.354,0.823 1.583,1.063 0.229,0.24 10 false 7 0.229,4.26 1.438,4.604 1.208,0.344 10 false Outer Mirror Switch Assembly 1.969,0.906 2.219,1.115 0.25,0.208 10 false E1 2.26,3.51 2.698,3.719 0.438,0.208 10 false MIRE 2.26,2.198 2.698,2.406 0.438,0.208 10 false MIRS 2.26,0.917 2.698,1.125 0.438,0.208 10 false MIRB 2.104,4.094 3.427,4.76 1.323,0.667 10 false Main Body ECU (Cowl Side Junction Block LH) 3.823,4.25 5.49,4.646 1.667,0.396 10 false Outer Mirror Control ECU 5.729,4.271 7.052,4.771 1.323,0.5 10 false Outer Rear View Mirror Assembly LH 2.688,2.635 3.188,2.844 0.5,0.208 10 false CANN 2.688,1.656 3.135,1.833 0.448,0.177 10 false CANP 4.104,2.646 4.563,2.833 0.458,0.188 10 false CANL 4.104,1.667 4.563,1.885 0.458,0.219 10 false CANH 3.177,2.469 3.427,2.656 0.25,0.188 10 false 15 3.177,1.479 3.427,1.656 0.25,0.177 10 false 16 3.844,2.5 4.188,2.688 0.344,0.188 10 false 21 3.906,1.51 4.167,1.708 0.26,0.198 10 false 1 4.844,2.229 5.302,2.448 0.458,0.219 10 false M+L 4.823,0.885 5.219,1.094 0.396,0.208 10 false MHL 4.844,3.5 5.26,3.719 0.417,0.219 10 false MVL 5.854,2.208 6.135,2.385 0.281,0.177 10 false M+ 5.854,0.885 6.135,1.063 0.281,0.177 10 false MH 5.865,3.49 6.146,3.667 0.281,0.177 10 false MV 5.635,3.385 5.885,3.563 0.25,0.177 10 false 7 5.615,2.104 5.917,2.302 0.302,0.198 10 false 8 5.625,0.771 5.896,0.948 0.271,0.177 10 false 9 5.219,3.385 5.521,3.583 0.302,0.198 10 false 20 5.219,2.104 5.49,2.302 0.271,0.198 10 false 18 5.219,0.771 5.479,0.927 0.26,0.156 10 false 19 0.865,5.313 2.948,5.583 2.083,0.271 10 false : CAN Communication Line 1.99,3.323 2.208,3.51 0.219,0.188 10 false 2 1.969,2.021 2.24,2.219 0.271,0.198 10 false 12 1.958,0.729 2.313,0.969 0.354,0.24 10 false 11 0.104,0.104 1.573,0.344 1.469,0.24 12 false for RHD: 1.969,2.188 2.219,2.396 0.25,0.208 10 false E1 1.969,3.5 2.219,3.708 0.25,0.208 10 false E1 3.177,1.646 3.427,1.854 0.25,0.208 10 false E3 3.188,2.646 3.438,2.854 0.25,0.208 10 false E3 5.74,4.083 6.094,4.281 0.354,0.198 10 false I35

PROCEDURE

1.CHECK DTC
a.

Use the intelligent tester to check if the CAN communication system is functioning normally .

Result
Result Proceed to
CAN DTC is not output A
CAN DTC is output (for LHD) B
CAN DTC is output (for RHD) C



A

2.READ VALUE USING INTELLIGENT TESTER (OUTER MIRROR SWITCH)

B

C

2.READ VALUE USING INTELLIGENT TESTER (OUTER MIRROR SWITCH)
a.

Check the Data List for proper functioning of the outer mirror switch (See page Vehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM(w/ Retract Mirror)>DATA LIST / ACTIVE TEST).

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Mirror Selection SW (R) Mirror master switch signal for RH mirror / ON or OFF ON: Switch is in R position
OFF: Switch is off or in L position
-
Mirror Selection SW (L) Mirror master switch signal for LH mirror / ON or OFF ON: Switch is in L position
OFF: Switch is off or in R position
-
Mirror Position SW (R) Mirror control switch signal (right) / ON or OFF ON: Right switch is on
OFF: Any switch except right is on or all switches are off
-
Mirror Position SW (L) Mirror control switch signal (left) / ON or OFF ON: Left switch is on
OFF: Any switch except left is on or all switches are off
-
Mirror Position SW (Up) Mirror control switch signal (up) / ON or OFF ON: Up switch is on
OFF: Any switch except up is on or all switches are off
-
Mirror Position SW (Dwn) Mirror control switch signal (down) / ON or OFF ON: Down switch is on
OFF: Any switch except down is on or all switches are off
-

OK:

On tester screen, each item changes between ON and OFF according to above chart.




OK

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (POWER MIRROR CONTROL FUNCTION)

NG

6.INSPECT OUTER MIRROR SWITCH ASSEMBLY
3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (POWER MIRROR CONTROL FUNCTION)
a.

Select the Active Test, use the intelligent tester to generate a control command, and then check the power mirror control function (See page Vehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM(w/ Retract Mirror)>DATA LIST / ACTIVE TEST).

Mirror
Tester Display Test Part Control Range Diagnostic Note
RH Mirror Up/Down Mirror vertical operation UP / OFF / DOWN -
RH Mirror Right/Left Mirror horizontal operation RIGHT / OFF / LEFT -
LH Mirror Up/Down Mirror vertical operation UP / OFF / DOWN -
LH Mirror Right/Left Mirror horizontal operation RIGHT / OFF / LEFT -

Result
Result Proceed to
Outer rear view mirror (for Passenger Side) does not operate normally A
Outer rear view mirror (for Passenger Side) operates normally B



A

4.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY (for Passenger Side)

B

REPLACE OUTER MIRROR CONTROL ECU

4.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY (for Passenger Side)
a.
B308844E02
2.323,3.771 2.813,4.24 true 2.177,3.771 2.313,4.365 true 1.927,3.76 1.708,4.365 true 2.802,4.25 3.063,4.448 0.26,0.198 10 false MH 2.292,4.385 2.552,4.583 0.26,0.198 10 false M+ 1.604,4.396 1.865,4.594 0.26,0.198 10 false MV 1.771,0.5 2.229,0.698 0.458,0.198 10 false (A) 1.396,0.844 1.854,1.042 0.458,0.198 10 false (C) 1.813,1.281 2.271,1.479 0.458,0.198 10 false (B) 2.25,0.792 2.708,0.99 0.458,0.198 10 false (D)

for LHD:


ii.

Apply battery voltage and check the operation of the power mirror.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 7 (MV)
Battery negative (-) → Terminal 8 (M+)
Turns upward (A)
Battery negative (-) → Terminal 7 (MV)
Battery positive (+) → Terminal 8 (M+)
Turns downward (B)
Battery positive (+) → Terminal 9 (MH)
Battery negative (-) → Terminal 8 (M+)
Turns left (C)
Battery negative (-) → Terminal 9 (MH)
Battery positive (+) → Terminal 8 (M+)
Turns right (D)




b.
B308845E02
2.26,3.688 2.635,4.208 true 2.125,3.667 2.292,4.323 true 1.854,3.667 1.76,4.313 true 2.625,4.24 2.938,4.438 0.313,0.198 10 false MH 1.667,4.344 1.979,4.542 0.313,0.198 10 false MV 2.208,4.344 2.521,4.542 0.313,0.198 10 false M+ 1.344,0.781 1.802,0.979 0.458,0.198 10 false (A) 0.906,1.104 1.365,1.302 0.458,0.198 10 false (C) 1.323,1.573 1.781,1.771 0.458,0.198 10 false (B) 1.75,1.135 2.208,1.333 0.458,0.198 10 false (D)

for RHD:


ii.

Apply battery voltage and check the operation of the power mirror.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 7 (MV)
Battery negative (-) → Terminal 8 (M+)
Turns upward (A)
Battery negative (-) → Terminal 7 (MV)
Battery positive (+) → Terminal 8 (M+)
Turns downward (B)
Battery positive (+) → Terminal 9 (MH)
Battery negative (-) → Terminal 8 (M+)
Turns left (C)
Battery negative (-) → Terminal 9 (MH)
Battery positive (+) → Terminal 8 (M+)
Turns right (D)





OK

5.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY - OUTER MIRROR CONTROL ECU)

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY (for Passenger Side)

5.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY - OUTER MIRROR CONTROL ECU)
a.
U164283E02
1.24,1.479 1.104,2.271 false 1.448,1.469 1.698,2.281 false 1.615,1.458 2.083,2.281 false 2.677,4.021 1.823,4.344 false 2.802,4.031 2.313,4.344 false 2.927,4.021 2.958,4.26 false 0.052,0.031 2.396,0.365 2.344,0.333 10 false Front view of wire harness connector: (to Outer Rear View Mirror RH) 0.083,2.615 2.427,2.948 2.344,0.333 10 false Front view of wire harness connector: (to Outer Mirror Control ECU) 0.177,1.115 0.427,1.271 0.25,0.156 10 false I32 0.135,3.583 0.396,3.74 0.26,0.156 10 false I18 1.615,2.292 1.875,2.458 0.26,0.167 10 false M+ 2.031,2.302 2.292,2.469 0.26,0.167 10 false MV 1.031,2.292 1.292,2.448 0.26,0.156 10 false MH 1.635,4.385 2.042,4.615 0.406,0.229 10 false M+R 2.188,4.385 2.604,4.615 0.417,0.229 10 false MHR 2.896,4.292 3.302,4.531 0.406,0.24 10 false MVR

for LHD:

i.

Disconnect the I18 ECU connector.


ii.

Disconnect the I32 mirror connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I18-38 (M+R) - I32-8 (M+) Always Below 1 Ω
I18-39 (MHR) - I32-9 (MH)
I18-40 (MVR) - I32-7 (MV)
I32-8 (M+) - Body ground Always 10 kΩ or higher
I32-9 (MH) - Body ground
I32-7 (MV) - Body ground




b.
U164284E02
1.229,1.479 1.094,2.271 false 1.438,1.469 1.688,2.281 false 1.615,1.458 2.083,2.281 false 2.656,3.854 1.688,4.385 false 2.781,3.865 2.167,4.385 false 2.938,3.865 3.115,4.26 false 0.052,0.031 2.396,0.365 2.344,0.333 10 false Front view of wire harness connector: (to Outer Rear View Mirror LH) 0.052,2.615 2.396,2.948 2.344,0.333 10 false Front view of wire harness connector: (to Outer Mirror Control ECU) 0.177,1.115 0.427,1.271 0.25,0.156 10 false I35 0.135,3.583 0.396,3.74 0.26,0.156 10 false I24 1.604,2.292 1.865,2.458 0.26,0.167 10 false M+ 2.031,2.302 2.292,2.469 0.26,0.167 10 false MV 1.021,2.292 1.281,2.448 0.26,0.156 10 false MH 1.49,4.427 1.958,4.625 0.469,0.198 10 false M+L 2.052,4.427 2.49,4.625 0.438,0.198 10 false MHL 2.979,4.292 3.417,4.521 0.438,0.229 10 false MVL

for RHD:

i.

Disconnect the I24 ECU connector.


ii.

Disconnect the I35 mirror connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I24-18 (M+L) - I35-8 (M+) Always Below 1 Ω
I24-19 (MHL) - I35-9 (MH)
I24-20 (MVL) - I35-7 (MV)
I35-8 (M+) - Body ground Always 10 kΩ or higher
I35-9 (MH) - Body ground
I35-7 (MV) - Body ground





OK

REPLACE OUTER MIRROR CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT OUTER MIRROR SWITCH ASSEMBLY
a.
B181045E09
1.271,4.135 1.323,3.76 false 0.771,4.146 1.167,3.76 false 1.927,4.156 1.479,3.75 false 1.125,4.177 1.5,4.344 0.375,0.167 10 false MSW 1.813,4.177 2.042,4.344 0.229,0.167 10 false M+ 0.698,4.177 0.833,4.344 0.135,0.167 10 false E

Remove the switch (See page Vehicle Exterior>MIRROR (EXT)>OUTER MIRROR SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
7 (M+) - 9 (E) Up switch pushed 95 to 105 Ω
Down switch pushed 446 to 493 Ω
Left switch pushed 760 to 840 Ω
Right switch pushed 237 to 262 Ω
No switches pushed 10 kΩ or higher
8 (MSW) - 9 (E) Mirror master switch R Below 1 Ω
Mirror master switch L 95 to 105 Ω
Mirror master switch off 10 kΩ or higher




OK

7.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH - MAIN BODY ECU)

NG

REPLACE OUTER MIRROR SWITCH ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH - MAIN BODY ECU)
a.

Disconnect the E1 ECU connector.

B449878E01
0.5,1.417 0.833,1.583 0.333,0.167 4.333,1.417 4.667,1.583 0.333,0.167 1,1.885 1.521,1.531 false 1.521,2.229 1.75,1.76 false 2.094,2.219 1.865,1.771 false 5.563,2.135 5.792,1.667 false 5.969,2.115 5.917,1.677 false 6.313,2.115 6.031,1.677 false 0.458,0.5 2.75,1.052 2.292,0.552 10 false Front view of wire harness connector: (to Main Body ECU) 4.458,0.531 6.75,1.083 2.292,0.552 10 false Front view of wire harness connector: (to Outer Mirror Switch) 0.635,1.844 1.25,2.042 0.615,0.198 10 false MIRE 1.333,2.271 1.948,2.469 0.615,0.198 10 false MIRB 2.01,2.271 2.625,2.469 0.615,0.198 10 false MIRS 0.583,1.417 0.896,1.615 0.313,0.198 10 false E1 4.417,1.417 4.729,1.615 0.313,0.198 10 false G1 5.438,2.167 6.052,2.365 0.615,0.198 10 false M+ 5.823,2.167 6.438,2.365 0.615,0.198 10 false MSW 6.292,2.167 6.906,2.365 0.615,0.198 10 false E


b.

Disconnect the G1 switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E1-2 (MIRE) - G1-9 (E) Always Below 1 Ω
E1-11 (MIRB) -G1-7 (M+)
E1-12 (MIRS) - G1-8 (MSW)
G1-9 (E) - Body ground Always 10 kΩ or higher
G1-7 (M+) - Body ground
G1-8 (MSW) - Body ground




OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR