Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM(w/ Retract Mirror) › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052853 MIRROR (EXT) _0255766 POWER MIRROR CONTROL SYSTEM(w/ Retract Mirror) J

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM(w/ Retract Mirror)  Power Mirrors do not Return to Memorized Position  


SYSTEM DESCRIPTION

When the seat memory switch 1, seat memory switch 2 or seat memory switch 3 is pressed, the position control ECU and switch mirror position signal is sent through the CAN communication line to the outer mirror control ECU. The outer mirror control ECU then activates the mirror control motors to move the mirrors to the previously recorded positions.

WIRING DIAGRAM

B188313E04
5.552,6.24 7.01,6.594 1.458,0.354 10 false Outer Rear View Mirror Assembly RH 5.552,6.063 5.781,6.219 0.229,0.156 10 false I32 2.979,6.479 4.604,6.667 1.625,0.188 10 false Outer Mirror Control ECU 1.021,7.375 2.729,7.563 1.708,0.188 10 false : CAN Communication Line 0.292,6.5 1.042,6.688 0.75,0.188 10 false *1: for LHD 0.292,6.823 1.042,7.01 0.75,0.188 10 false *2: for RHD 0.271,5.146 1.667,5.5 1.396,0.354 10 false Position Control ECU and Switch 0.302,2.073 1.615,2.271 1.313,0.198 10 false Seat Memory Switch 5.552,2.26 7.01,2.615 1.458,0.354 10 false Outer Rear View Mirror Assembly LH 5.563,2.083 5.792,2.24 0.229,0.156 10 false I35 5.76,1.771 5.99,1.927 0.229,0.156 10 false E1 5.76,1.406 6.167,1.563 0.406,0.156 10 false HSRL 5.76,1.052 6.156,1.208 0.396,0.156 10 false VSRL 5.76,0.667 5.99,0.823 0.229,0.156 10 false VC 4.167,1.771 4.458,1.927 0.292,0.156 10 false LE1 4.042,1.406 4.458,1.563 0.417,0.156 10 false HSRL 4.125,1.031 4.458,1.188 0.333,0.156 10 false VSR 4.156,0.667 4.458,0.823 0.302,0.156 10 false LVC 5.479,0.573 5.729,0.729 0.25,0.156 10 false 10 5.49,0.948 5.667,1.104 0.177,0.156 10 false 22 5.479,1.323 5.677,1.479 0.198,0.156 10 false 11 5.49,1.688 5.667,1.844 0.177,0.156 10 false 21 5.479,4.552 5.729,4.708 0.25,0.156 10 false 10 5.49,4.917 5.667,5.073 0.177,0.156 10 false 22 5.479,5.292 5.677,5.448 0.198,0.156 10 false 11 5.49,5.667 5.667,5.823 0.177,0.156 10 false 21 4.573,0.49 4.823,0.646 0.25,0.156 10 false 2*1 4.573,0.667 4.823,0.823 0.25,0.156 10 false I18 4.583,1.031 4.833,1.188 0.25,0.156 10 false I18 4.573,1.406 4.823,1.563 0.25,0.156 10 false I18 4.573,1.771 4.823,1.927 0.25,0.156 10 false I18 4.573,0.854 4.833,1.01 0.26,0.156 10 false 4*1 4.573,1.219 4.833,1.375 0.26,0.156 10 false 5*1 4.573,1.594 4.823,1.75 0.25,0.156 10 false 3*1 4.906,0.49 5.156,0.646 0.25,0.156 10 false 2*2 4.906,0.667 5.156,0.823 0.25,0.156 10 false I24 4.906,1.031 5.156,1.188 0.25,0.156 10 false I24 4.906,1.406 5.156,1.563 0.25,0.156 10 false I24 4.906,1.771 5.156,1.927 0.25,0.156 10 false I24 4.906,0.854 5.167,1.01 0.26,0.156 10 false 4*2 4.906,1.219 5.167,1.375 0.26,0.156 10 false 5*2 4.906,1.594 5.156,1.75 0.25,0.156 10 false 3*2 2.469,0.5 2.719,0.656 0.25,0.156 10 false 7*1 2.469,0.677 2.719,0.833 0.25,0.156 10 false I18 2.469,1.052 2.719,1.208 0.25,0.156 10 false I18 2.479,1.417 2.729,1.573 0.25,0.156 10 false I18 2.49,1.792 2.74,1.948 0.25,0.156 10 false I18 2.469,0.875 2.729,1.031 0.26,0.156 10 false 6*1 2.469,1.24 2.729,1.396 0.26,0.156 10 false 9*1 2.427,1.615 2.74,1.771 0.313,0.156 10 false 10*1 2.792,0.5 3.042,0.656 0.25,0.156 10 false 7*2 2.802,0.677 3.052,0.833 0.25,0.156 10 false I24 2.469,0.146 2.719,0.302 0.25,0.156 10 false 8*1 2.469,0.313 2.719,0.469 0.25,0.156 10 false I18 2.792,0.146 3.042,0.302 0.25,0.156 10 false 8*2 2.802,0.302 3.052,0.458 0.25,0.156 10 false I24 2.813,1.052 3.063,1.208 0.25,0.156 10 false I24 2.813,1.417 3.063,1.573 0.25,0.156 10 false I24 2.813,1.792 3.063,1.948 0.25,0.156 10 false I24 2.792,0.885 3.052,1.042 0.26,0.156 10 false 6*2 2.792,1.24 3.052,1.396 0.26,0.156 10 false 9*2 2.76,1.615 3.073,1.771 0.313,0.156 10 false 10*2 1.563,0.5 1.813,0.656 0.25,0.156 10 false 3*1 1.594,0.677 1.844,0.833 0.25,0.156 10 false X1 1.594,1.042 1.844,1.198 0.25,0.156 10 false X1 1.583,1.417 1.833,1.573 0.25,0.156 10 false X1 1.594,1.792 1.844,1.948 0.25,0.156 10 false X1 1.563,0.875 1.823,1.031 0.26,0.156 10 false 2*1 1.563,1.24 1.823,1.396 0.26,0.156 10 false 5*1 1.563,1.604 1.802,1.76 0.24,0.156 10 false 6*1 1.875,0.5 2.125,0.656 0.25,0.156 10 false 3*2 1.927,0.688 2.177,0.844 0.25,0.156 10 false X2 1.563,0.135 1.813,0.292 0.25,0.156 10 false 4*1 1.594,0.302 1.844,0.458 0.25,0.156 10 false X1 1.875,0.135 2.125,0.292 0.25,0.156 10 false 4*2 1.927,0.313 2.177,0.469 0.25,0.156 10 false X2 1.927,1.052 2.177,1.208 0.25,0.156 10 false X2 1.917,1.417 2.167,1.573 0.25,0.156 10 false X2 1.927,1.792 2.177,1.948 0.25,0.156 10 false X2 1.875,0.875 2.135,1.031 0.26,0.156 10 false 2*2 1.875,1.25 2.135,1.406 0.26,0.156 10 false 5*2 1.875,1.604 2.125,1.76 0.25,0.156 10 false 6*2 2.479,3.563 2.729,3.719 0.25,0.156 10 false I18 2.417,3.385 2.729,3.542 0.313,0.156 10 false 21*1 2.802,3.563 3.052,3.719 0.25,0.156 10 false I24 2.76,3.385 3.073,3.542 0.313,0.156 10 false 21*2 1.542,3.563 1.792,3.719 0.25,0.156 10 false c15 1.542,3.375 1.781,3.531 0.24,0.156 10 false 1*1 1.875,3.563 2.125,3.719 0.25,0.156 10 false c27 1.865,3.375 2.115,3.531 0.25,0.156 10 false 1*2 2.479,4.677 2.729,4.833 0.25,0.156 10 false I18 2.458,4.5 2.688,4.656 0.229,0.156 10 false 1*1 2.802,4.677 3.052,4.833 0.25,0.156 10 false I24 2.792,4.5 3.042,4.656 0.25,0.156 10 false 1*2 1.542,4.677 1.792,4.833 0.25,0.156 10 false c15 1.552,4.5 1.792,4.656 0.24,0.156 10 false 5*1 1.875,4.677 2.125,4.833 0.25,0.156 10 false c27 1.885,4.5 2.135,4.656 0.25,0.156 10 false 5*2 4.542,4.469 4.854,4.625 0.313,0.156 10 false 22*1 4.583,4.656 4.833,4.813 0.25,0.156 10 false I18 4.583,5.021 4.833,5.177 0.25,0.156 10 false I18 4.573,5.385 4.823,5.542 0.25,0.156 10 false I18 4.583,5.76 4.833,5.917 0.25,0.156 10 false I18 4.542,4.844 4.854,5 0.313,0.156 10 false 24*1 4.542,5.208 4.854,5.365 0.313,0.156 10 false 25*1 4.542,5.573 4.844,5.729 0.302,0.156 10 false 23*1 4.906,4.479 5.208,4.635 0.302,0.156 10 false 22*2 4.906,4.656 5.156,4.813 0.25,0.156 10 false I24 4.917,5.021 5.167,5.177 0.25,0.156 10 false I24 4.906,5.385 5.156,5.542 0.25,0.156 10 false I24 4.906,5.76 5.156,5.917 0.25,0.156 10 false I24 4.906,4.844 5.229,5 0.323,0.156 10 false 24*2 4.906,5.208 5.229,5.365 0.323,0.156 10 false 25*2 4.906,5.573 5.229,5.729 0.323,0.156 10 false 23*2 5.76,5.76 5.99,5.917 0.229,0.156 10 false E1 5.76,5.396 6.167,5.552 0.406,0.156 10 false HSSR 5.76,5.021 6.156,5.177 0.396,0.156 10 false VSSR 5.75,4.656 5.979,4.813 0.229,0.156 10 false VC 4.167,5.75 4.458,5.906 0.292,0.156 10 false RE1 4.031,5.396 4.448,5.552 0.417,0.156 10 false HSRR 4.031,5.021 4.479,5.177 0.448,0.156 10 false VSRR 4.104,4.646 4.458,4.802 0.354,0.156 10 false RVC 3.125,1.792 3.594,1.948 0.469,0.156 10 false MSWE 3.125,1.417 3.385,1.573 0.26,0.156 10 false MM 3.125,1.052 3.354,1.208 0.229,0.156 10 false M3 3.125,0.677 3.354,0.833 0.229,0.156 10 false M2 1.344,1.792 1.458,1.948 0.115,0.156 10 false E 1.104,1.417 1.458,1.573 0.354,0.156 10 false MRY 1.24,1.052 1.458,1.208 0.219,0.156 10 false M3 1.24,0.677 1.458,0.833 0.219,0.156 10 false M2 3.125,0.313 3.354,0.469 0.229,0.156 10 false M1 1.24,0.302 1.458,0.458 0.219,0.156 10 false M1 3.125,3.563 3.542,3.719 0.417,0.156 10 false CANL 1.042,3.573 1.563,3.729 0.521,0.156 10 false MPX2 3.125,4.677 3.563,4.833 0.438,0.156 10 false CANH 1.031,4.688 1.458,4.844 0.427,0.156 10 false MPX1

PROCEDURE

1.CHECK DTC
a.

Use the intelligent tester to check if the CAN communication system is functioning normally.

Result
Result Proceed to
CAN DTC is not output A
CAN DTC is output (for LHD) B
CAN DTC is output (for RHD) C



A

2.CHECK POWER MIRROR CONTROL FUNCTION

B

C

2.CHECK POWER MIRROR CONTROL FUNCTION
a.

Check that the mirror surface positions of the outer rear view mirror LH and RH can be moved using the outer mirror switch.

OK:

Mirror surface positions of the outer rear view mirror LH and RH can be moved using the outer mirror switch.




OK

3.READ VALUE USING INTELLIGENT TESTER (MIRROR POSITION MEMORY)

NG

PROCEED TO NEXT INSPECTION PROCEDURE SHOWN IN PROBLEM SYMPTOMS TABLE

3.READ VALUE USING INTELLIGENT TESTER (MIRROR POSITION MEMORY)
a.

Check the Data List for proper functioning of the mirror position memory (See page Vehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM(w/ Retract Mirror)>DATA LIST / ACTIVE TEST).

Mirror
Tester Display Measurement Item/Display Normal Condition Diagnostic Note
Mirror Memory No.1 Mirror position memorized in seat memory switch memory1 / ON or OFF ON: Memorized
OFF: Not memorized
-
Mirror Memory No.2 Mirror position memorized in seat memory switch memory2 / ON or OFF ON: Memorized
OFF: Not memorized
-
Mirror Memory No.3 Mirror position memorized in seat memory switch memory3 / ON or OFF ON: Memorized
OFF: Not memorized
-

OK:

On tester screen, each item changes between ON and OFF according to above chart.




OK

4.READ VALUE USING INTELLIGENT TESTER (MIRROR POSITION SENSOR)

NG

REPLACE OUTER MIRROR CONTROL ECU

4.READ VALUE USING INTELLIGENT TESTER (MIRROR POSITION SENSOR)
a.

Check the Data List for proper functioning of the mirror position sensor (See page Vehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM(w/ Retract Mirror)>DATA LIST / ACTIVE TEST).

Mirror
Tester Display Measurement Item/Display Normal Condition Diagnostic Note
RH Mir Position Sensor V RH side mirror vertical sensor voltage / MIN: 0 V, MAX: 5 V Within range from 0 to 5 V -
RH Mir Position Sensor H RH side mirror horizontal sensor voltage / MIN: 0 V, MAX: 5 V Within range from 0 to 5 V -
LH Mir Position Sensor V LH side mirror vertical sensor voltage / MIN: 0 V, MAX: 5 V Within range from 0 to 5 V -
LH Mir Position Sensor H LH side mirror horizontal sensor voltage / MIN: 0 V, MAX: 5 V Within range from 0 to 5 V -

OK:

When mirror control switch is operated, voltage changes within range shown in above chart.


Result
Result Proceed to
LH side mirror does not operate normally A
RH side mirror does not operate normally B
Mirror operates normally C



A

5.CHECK OUTER MIRROR CONTROL ECU

B

7.CHECK OUTER MIRROR CONTROL ECU

C

5.CHECK OUTER MIRROR CONTROL ECU
U164086E01
0.844,1.116 1.073,1.280 0.228,0.164 10 I18 1.174,1.115 1.330,1.281 0.156,0.166 10 *1 0.844,1.394 1.073,1.558 0.228,0.164 10 I24 1.174,1.393 1.330,1.559 0.156,0.166 10 *2 3.551,2.265 3.824,2.431 0.273,0.166 10 LE1 4.027,2.116 4.319,2.282 0.292,0.166 10 LVC 0.121,2.027 0.835,2.194 0.714,0.166 10 *1: for LHD 0.125,2.324 0.886,2.490 0.762,0.166 10 *2: for RHD 3.655,2.244 3.668,1.289 false 4.143,2.1 3.758,1.289 false

a.

for LHD:

i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I18-2 (LVC) - I18-3 (LE1) Engine switch on (IG) 4.7 to 5.5 V



ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I18-3 (LE1) - Body ground Always Below 1 Ω




b.

for RHD:

i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I24-2 (LVC) - I24-3 (LE1) Engine switch on (IG) 4.7 to 5.5 V



ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I24-3 (LE1) - Body ground Always Below 1 Ω





OK

6.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR LH - OUTER MIRROR CONTROL ECU)

NG

REPLACE OUTER MIRROR CONTROL ECU

6.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR LH - OUTER MIRROR CONTROL ECU)
a.
U164289E02
1.052,1.417 0.667,1.583 false 1.063,1.625 0.75,1.875 false 1.229,1.302 3.073,0.958 false 1.229,1.615 2.771,2.021 false 0.979,3.583 1.323,4.104 false 1.094,3.583 1.76,4.115 false 1.219,3.51 2.958,3.094 false 1.333,3.573 2.417,4.094 false 0.052,0.052 2.396,0.385 2.344,0.333 10 false Front view of wire harness connector: (to Outer Rear View Mirror LH) 0.052,2.24 2.396,2.573 2.344,0.333 10 false Front view of wire harness connector: (to Outer Mirror Control ECU) 0.167,1.125 0.417,1.281 0.25,0.156 10 false I35 0.115,3.25 0.375,3.406 0.26,0.156 10 false I18 0.438,3.24 0.646,3.396 0.208,0.156 10 false *1 0.458,3.573 0.667,3.729 0.208,0.156 10 false *2 0.125,3.573 0.365,3.729 0.24,0.156 10 false I24 0.26,1.823 0.698,1.99 0.438,0.167 10 false VSRL 3.156,0.865 3.417,1.031 0.26,0.167 10 false VC 0.198,1.51 0.635,1.667 0.438,0.156 10 false HSRL 2.885,1.938 3.146,2.104 0.26,0.167 10 false E1 1.188,4.125 1.51,4.333 0.323,0.208 10 false LVC 0.063,4.042 1.052,4.177 0.99,0.135 10 false *1: for LHD 0.063,4.323 1.052,4.458 0.99,0.135 10 false *2: for RHD 1.729,4.146 2.042,4.344 0.313,0.198 10 false LE1 3.042,3.021 3.427,3.219 0.385,0.198 10 false VSR 2.5,4.063 2.969,4.271 0.469,0.208 10 false HSRL

for LHD:

i.

Disconnect the I18 ECU connector.


ii.

Disconnect the I35 mirror connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I18-2 (LVC) - I35-10 (VC) Always Below 1 Ω
I18-3 (LE1) - I35-21 (E1)
I18-4 (VSR) - I35-22 (VSRL)
I18-5 (HSRL) - I35-11 (HSRL)
I35-10 (VC) - Body ground Always 10 kΩ or higher
I35-21 (E1) - Body ground
I35-22 (VSRL) - Body ground
I35-11 (HSRL) - Body ground




b.

for RHD:

i.

Disconnect the I24 ECU connector.


ii.

Disconnect the I35 mirror connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I24-2 (LVC) - I35-10 (VC) Always Below 1 Ω
I24-3 (LE1) - I35-21 (E1)
I24-4 (VSR) - I35-22 (VSRL)
I24-5 (HSRL) - I35-11 (HSRL)
I35-10 (VC) - Body ground Always 10 kΩ or higher
I35-21 (E1) - Body ground
I35-22 (VSRL) - Body ground
I35-11 (HSRL) - Body ground





OK

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK OUTER MIRROR CONTROL ECU
U164087E02
3.677,2.292 3.667,1.438 false 4.167,2.146 3.76,1.438 false 0.844,1.115 1.073,1.281 0.229,0.167 10 false I18 1.177,1.115 1.333,1.281 0.156,0.167 10 false *1 0.844,1.396 1.073,1.563 0.229,0.167 10 false I24 1.177,1.396 1.333,1.563 0.156,0.167 10 false *2 3.552,2.302 3.854,2.469 0.302,0.167 10 false RE1 4.031,2.156 4.354,2.323 0.323,0.167 10 false RVC 0.125,2.031 0.844,2.198 0.719,0.167 10 false *1: for LHD 0.125,2.323 0.885,2.49 0.76,0.167 10 false *2: for RHD

a.

for LHD:

i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I18-22 (RVC) - I18-23 (RE1) Engine switch on (IG) 4.7 to 5.5 V



ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I18-23 (RE1) - Body ground Always Below 1 Ω




b.

for RHD:

i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I24-22 (RVC) - I24-23 (RE1) Engine switch on (IG) 4.7 to 5.5 V



ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I24-23 (RE1) - Body ground Always Below 1 Ω





OK

8.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR RH - OUTER MIRROR CONTROL ECU)

NG

REPLACE OUTER MIRROR CONTROL ECU

8.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR RH - OUTER MIRROR CONTROL ECU)
a.
U164290E02
1.063,1.417 0.677,1.583 false 1.063,1.625 0.75,1.875 false 1.24,1.302 2.979,0.958 false 1.229,1.615 2.771,2.021 false 0.99,3.74 1.333,4.104 false 1.115,3.74 1.781,4.115 false 1.219,3.656 2.771,2.958 false 1.344,3.729 2.448,4.115 false 0.052,0.031 2.396,0.365 2.344,0.333 10 false Front view of wire harness connector: (to Outer Rear View Mirror RH) 0.063,2.24 2.406,2.573 2.344,0.333 10 false Front view of wire harness connector: (to Outer Mirror Control ECU) 0.177,1.125 0.427,1.281 0.25,0.156 10 false I32 0.125,3.25 0.385,3.406 0.26,0.156 10 false I18 0.438,3.24 0.646,3.396 0.208,0.156 10 false *1 0.458,3.573 0.667,3.729 0.208,0.156 10 false *2 0.125,3.573 0.365,3.729 0.24,0.156 10 false I24 0.26,1.823 0.698,1.99 0.438,0.167 10 false VSSR 3.073,0.865 3.333,1.031 0.26,0.167 10 false VC 0.198,1.51 0.635,1.667 0.438,0.156 10 false HSSR 2.885,1.938 3.146,2.104 0.26,0.167 10 false E1 1.188,4.125 1.49,4.396 0.302,0.271 10 false RVC 0.063,4.042 1.063,4.24 1,0.198 10 false *1: for LHD 0.063,4.323 1.083,4.51 1.021,0.188 10 false *2: for RHD 1.729,4.146 2.063,4.354 0.333,0.208 10 false RE1 2.865,2.885 3.292,3.146 0.427,0.26 10 false VSRR 2.5,4.063 2.958,4.302 0.458,0.24 10 false HSRR

for LHD:

i.

Disconnect the I18 ECU connector.


ii.

Disconnect the I32 mirror connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I18-22 (RVC) - I32-10 (VC) Always Below 1 Ω
I18-23 (RE1) - I32-21 (E1)
I18-24 (VSRR) - I32-22 (VSSR)
I18-25 (HSRR) - I32-11 (HSSR)
I32-10 (VC) - Body ground Always 10 kΩ or higher
I32-21 (E1) - Body ground
I32-22 (VSSR) - Body ground
I32-11 (HSSR) - Body ground




b.

for RHD:

i.

Disconnect the I24 ECU connector.


ii.

Disconnect the I32 mirror connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I24-22 (RVC) - I32-10 (VC) Always Below 1 Ω
I24-23 (RE1) - I32-21 (E1)
I24-24 (VSRR) - I32-22 (VSSR)
I24-25 (HSRR) - I32-11 (HSSR)
I32-10 (VC) - Body ground Always 10 kΩ or higher
I32-21 (E1) - Body ground
I32-22 (VSSR) - Body ground
I32-11 (HSSR) - Body ground





OK

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR