Home › Vehicle Exterior › MIRROR (EXT) › OUTER REAR VIEW MIRROR COVER › 2015.08–2018.08
RM2660E _59 Vehicle Exterior _052853 MIRROR (EXT) _0255768 OUTER REAR VIEW MIRROR COVER A

MIRROR (EXT)  OUTER REAR VIEW MIRROR COVER  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 87945B 2.REMOVE OUTER MIRROR COVER LH

HINT:

Be sure to detach the claws of the outer mirror cover in the order shown in the illustration.


B241698E10
1.323,1.344 1.427,1.51 0.104,0.167 10 true 1 1.865,1.333 1.969,1.5 0.104,0.167 10 true 2 2.25,1.188 2.354,1.354 0.104,0.167 10 true 3 2.125,2.073 2.229,2.24 0.104,0.167 10 true 5 1.406,1.99 1.51,2.156 0.104,0.167 10 true 6 0.75,1.542 0.854,1.708 0.104,0.167 10 true 7 0.531,1.813 0.635,1.979 0.104,0.167 10 true 8 2.396,1.615 2.5,1.781 0.104,0.167 10 true 4

a.
U115642E01
2.54,2.826 2.793,3.072 0.253,0.246 10 *1

Using 2 screwdrivers, detach the 2 claws.

HINT:

Tape the screwdriver tip before use.


Text in Illustration
*1 Protective Tape


b.

Insert a screwdriver into the slot as shown in the illustration and push on the outer mirror body to create a space between the outer mirror body and outer mirror cover.

NOTICE:

Be careful not to break the ribs.


HINT:

Tape the screwdriver tip before use.


B245757E08
5.865,1.802 5.865,2.021 false 6.344,1.302 6.417,0.979 6.417,0.979 6.531,0.979 false 6.552,0.927 6.781,1.115 0.229,0.188 10 true *1 5.802,2.052 5.948,2.198 0.146,0.146 10 false *2 5.938,0.427 6.167,0.583 0.229,0.156 10 false *a

Text in Illustration
*1 Protective Tape *2 Rib
*a Inner Side of Outer Mirror Cover - -


c.
U155878E01
0.712,0.234 0.921,0.406 0.209,0.172 10 *1 2.697,0.162 2.885,0.350 0.188,0.188 10 a

Insert a moulding remover into the space made between the outer mirror body and outer mirror cover.

NOTICE:

Do not insert the moulding remover more than 4 mm (0.157 in.).


HINT:

Tape the moulding remover before use.


Standard:
Area Specified Condition
a 4mm


Text in Illustration
*1 Protective Tape


d.
B302379E03
0.917,0.406 1.281,0.24 1.281,0.24 0.896,0.563 false 0.427,3.792 0.604,3.979 0.177,0.188 10 false a 1.323,0.167 1.552,0.396 0.229,0.229 10 false *1 2.302,0.208 2.531,0.438 0.229,0.229 10 false b

Slide the moulding remover downwards as shown in the illustration to detach the 2 claws.

NOTICE:
·

Do not insert the moulding remover more than 4 mm (0.157 in.).

·

Do not slide the moulding remover past the point approximately 40 mm (1.57 in.) from the bottom edge of the outer mirror cover as the outer mirror body will become damaged.



Standard:
Area Specified Condition
a 40mm
b 4mm


Text in Illustration
*1 Protective Tape


e.

Remove the moulding remover B.


f.
U155866E01
1.935,0.428 2.114,0.575 0.179,0.147 10 *1 0.594,0.09 0.773,0.237 0.179,0.147 10 *a 2.136,0.503 2.359,0.503 2.359,0.503 2.537,0.967 false

Apply protective tape to the areas of the body cover and outer mirror cover as shown in the illustration.

Text in Illustration
*1 Protective Tape
*a Lower Side


g.

Insert a moulding remover B between the outer mirror cover and outer mirror body as shown in the illustration and detach the claw.


h.
B245633E04
1.969,0.865 2.125,1.073 2.125,1.073 2.25,1.073 false 2.271,0.979 2.458,1.177 0.188,0.198 10 false *1

Using a screwdriver, detach the claw.

Text in Illustration
*1 Protective Tape


i.
B245761

Detach the 2 claws and remove the outer mirror cover.

NOTICE:

When removing the cover, be careful not to damage the side turn signal light assembly or cover.