Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM(w/ Rain Sensor) › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052854 WIPER / WASHER _0255769 WIPER AND WASHER SYSTEM(w/ Rain Sensor) U

WIPER / WASHER  WIPER AND WASHER SYSTEM(w/ Rain Sensor)  TERMINALS OF ECU  


CHECK WINDSHIELD WIPER ECU


U165926E03
2.073,0.583 2.333,0.76 0.26,0.177 10 false E83 4.615,0.552 4.875,0.729 0.26,0.177 10 false E85

a.

Disconnect the E83 and E85 ECU connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
E83-5 (IG1I) - E85-10 (E) G - W-B IG signal circuit Engine switch off Below 1 V
Engine switch on (IG) 11 to 14 V
E85-10 (E) - Body ground W-B - Body ground Ground circuit Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the E83 and E85 ECU connectors.


d.

Measure the voltage and waveform according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
E83-7 (+SM) - Body ground W - Body ground Front wiper motor operation signal Front wiper is operated 11 to 14 V
Front wiper is stopped Below 1 V
E83-8 (WIG) - Body ground B - Body ground Front wiper motor power source circuit Engine switch off Below 1 V
Engine switch on (IG) 11 to 14 V
E83-10 (1S) - Body ground P - Body ground Front wiper motor power supply circuit Front wiper switch off Below 1 V
Front wiper switch LO 11 to 14 V
E83-9 (2S) - Body ground R - Body ground Front wiper motor power supply circuit (HI signal) Front wiper switch off Below 1 V
Front wiper switch HI 11 to 14 V
E85-2 (W) - Body ground L - Body ground Front washer motor power source circuit Front washer switch off Below 1 V
Front washer switch on 11 to 14 V
E85-5 (CANL) - Body ground R - Body ground CAN communication signal Engine switch on (IG) Pulse generation
E85-6 (CANH) - Body ground LG - Body ground CAN communication signal Engine switch on (IG) Pulse generation
E85-7 (MPX1) - Body ground R - Body ground LIN communication signal Engine switch on (IG) Pulse generation



CHECK WINDSHIELD WIPER SWITCH


U166072E02
1.542,0.135 2.49,0.354 0.948,0.219 12 false for RH side: 4.979,0.177 5.906,0.396 0.927,0.219 12 false for LH side: 1.427,0.656 1.688,0.833 0.26,0.177 10 false E16 2.156,0.656 2.417,0.833 0.26,0.177 10 false E15 5.521,0.708 5.781,0.885 0.26,0.177 10 false E16 4.74,0.708 5,0.885 0.26,0.177 10 false E15

a.

Disconnect the E16 switch connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
E16-2 (+B) - E16-10 (E)*1 B - W-B Power source circuit (from battery) Engine switch off Below 1 V
Engine switch on (IG) 11 to 14 V
E16-3 (+B) - E16-5 (E)*2 B - W-B Power source circuit (from battery) Engine switch off Below 1 V
Engine switch on (IG) 11 to 14 V
E16-10 (E) - Body ground*1 W-B - Body ground Ground circuit Always Below 1 Ω
E16-5 (E) - Body ground*2 W-B - Body ground Ground circuit Always Below 1 Ω

HINT:
·

*1: for LH Side

·

*2: for RH Side





CHECK MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)


U164692E05
2.875,1.094 2.781,1.094 2.781,1.094 2.365,1.354 true 5.51,0.698 5.427,0.698 5.427,0.698 5.01,0.958 true 2.865,1.635 2.792,1.635 2.792,1.635 2.385,1.792 true 2.906,2.635 2.813,2.635 2.813,2.635 2.396,2.385 true 2.885,2.229 2.813,2.229 2.813,2.229 2.406,2.135 true 2.24,2.792 2.469,2.958 0.229,0.167 10 false 2A 1.083,3.635 1.313,3.802 0.229,0.167 10 false 2A 1.958,2.042 2.208,2.24 0.25,0.198 10 false 2B 3.083,3.635 3.292,3.802 0.208,0.167 10 false 2B 1.958,1.177 2.167,1.344 0.208,0.167 10 false 2C 5.635,3.635 5.844,3.802 0.208,0.167 10 false 2C 4.938,1.656 5.146,1.823 0.208,0.167 10 false 2D 1.552,5.177 1.76,5.344 0.208,0.167 10 false 2D 4.406,5.177 4.615,5.344 0.208,0.167 10 false 2E 5.552,0.615 5.76,0.781 0.208,0.167 10 false 2E 2.917,1.021 3.135,1.188 0.219,0.167 10 false E1 6.042,7.01 6.26,7.177 0.219,0.167 10 false E1 2.917,1.542 3.135,1.708 0.219,0.167 10 false E2 3.531,7.01 3.75,7.177 0.219,0.167 10 false E2 2.917,2.146 3.135,2.313 0.219,0.167 10 false E3 1.063,7 1.281,7.167 0.219,0.167 10 false E3 2.948,2.552 3.167,2.719 0.219,0.167 10 false E4 6.094,5.083 6.313,5.25 0.219,0.167 10 false E4

a.

Disconnect the 2D, E2 and E1 main body ECU connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
E1-6 (AM1) - 2D-62 (GND2) W - W-B Power source circuit (from battery) Always 11 to 14 V
E2-11 (IG2D) - 2D-62 (GND2) B - W-B IG signal circuit Engine switch off Below 1 V
Engine switch on (IG) 11 to 14 V
2B-22 (STP) - 2D-62 (GND2) R - W-B Stop light switch circuit Stop light switch off Below 1 V
Stop light switch on 11 to 14 V
2D-62 (GND2) - Body ground W-B - Body ground Ground circuit Always Below 1 Ω


c.

Reconnect the 2D, E2 and E1 main body ECU connectors.


d.

Measure the voltage and waveform according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
E2-13 (HDLO) - Body ground L - Body ground Headlight low beam operation signal Engine switch on (IG)
Headlight dimmer switch in head
11 to 14 V
Engine switch on (IG)
Headlight dimmer switch not in head
Below 1 V
E3-15 (CANN) - Body ground R - Body ground CAN communication signal Engine switch on (IG) Pulse generation
E3-16 (CANP) - Body ground GR - Body ground CAN communication signal Engine switch on (IG) Pulse generation



CHECK MAP LIGHT


U165927E02
3.51,0.354 3.708,0.531 0.198,0.177 10 false R7

a.

Disconnect the R7 map light connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
R7-14 (IG) - R7-3 (GND5) G - W-B IG signal circuit Engine switch off Below 1 V
Engine switch on (IG) 11 to 14 V
R7-3 (GND5) - Body ground W-B - Body ground Ground circuit Always Below 1 Ω



CHECK RAIN SENSOR


U156599E08
3.479,0.177 3.802,0.354 0.323,0.177 10 false R11

a.

Disconnect the R11 rain sensor connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
R11-4 (SIG) - Body ground G - Body ground IG signal circuit Engine switch off Below 1 V
Engine switch on (IG) 11 to 14 V
R11-1 (ES) - Body ground W - Body ground Ground circuit Always Below 1 Ω


c.

Reconnect the R11 rain sensor connector.


d.

Measure the waveform according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
R11-3 (MPX) - Body ground R - Body ground LIN communication signal Engine switch on (IG) Pulse generation



CHECK HEADLIGHT CLEANER CONTROL RELAY (w/ Headlight Cleaner System)


E139344

HINT:

The headlight cleaner control relay uses waterproof connector. Therefore, voltage cannot be checked with the connector connected to the vehicle.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
3 (IG) - 4 (E) - IG signal circuit Engine switch off Below 1 V
Engine switch on (IG) 11 to 14 V
4 (E) - Body ground - Ground circuit Always Below 1 Ω
6 (PB) - 4 (E) - Headlight cleaner motor operation signal Headlight cleaner motor is stopped 11 to 14 V
Headlight cleaner motor is operating Below 1 V
2 (H) - 4 (E) - Headlight cleaner switch and headlight switch operation signal Engine switch on (IG)
Headlight cleaner switch is off
Below 1 V
Engine switch on (IG)
Headlight switch is off
Below 1 V
Engine switch on (IG)
Headlight cleaner switch is on and headlight dimmer switch in HEAD
11 to 14 V
5 (FRWA) - 4 (E)* - Front washer switch operation signal Engine switch on (IG)
Front washer switch is off
11 to 14 V
Engine switch on (IG)
Front washer switch is on
Below 1 V
1 (HDLO) - 4 (E)* - Headlight low beam operation signal Engine switch on (IG)
Headlight dimmer switch in HEAD
11 to 14 V
Engine switch on (IG)
Headlight dimmer switch not in HEAD
Below 1 V

*: w/ Headlight Auto Leveling



NO. 2 MULTIPLEX NETWORK BODY ECU (w/ Washer Nozzle Heater System)


U164149E03
3.125,0.344 3.385,0.5 0.26,0.156 10 false L50 4.344,0.344 4.604,0.5 0.26,0.156 10 false L51

a.

Disconnect the L50 and L51 No. 2 multiplex network body ECU connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L50-14 (BECU) - Body ground R - Body ground Power source circuit Always 11 to 14 V
L50-13 (SIG) - Body ground G - Body ground IG signal circuit Engine switch off Below 1 V
Engine switch on (IG) 11 to 14 V
L50-7 (GND) - Body ground W-B - Body ground Ground circuit Always Below 1 Ω


c.

Reconnect the L50 and L51 No. 2 multiplex network body ECU connectors.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L50-25 (WHTR) - Body ground GR - Body ground Washer nozzle heater signal circuit Engine switch on (IG), ambient temperature 6°C (42°F) or higher 11 to 14 V
Engine switch on (IG), ambient temperature 5°C (41°F) or less Below 1 V