Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM(w/ Rain Sensor) › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052854 WIPER / WASHER _0255769 WIPER AND WASHER SYSTEM(w/ Rain Sensor) J

WIPER / WASHER  WIPER AND WASHER SYSTEM(w/ Rain Sensor)  Wiper and Washer Switch Circuit  


DESCRIPTION

This circuit provides power to operate the windshield wiper switch. The manual operation signals are sent to the windshield wiper ECU.

WIRING DIAGRAM

E158177E08
1.171,2.929 2.743,3.080 1.573,0.151 10 Windshield Wiper Switch 6.011,0.596 7.137,0.944 1.126,0.347 10 from IG1 NO.1 Relay 4.742,0.585 5.706,0.812 0.963,0.228 10 ECU-IG No. 1 2.408,0.211 2.564,0.392 0.156,0.181 10 3 2.111,0.527 2.302,0.708 0.191,0.181 10 +B 2.198,2.007 2.354,2.188 0.156,0.181 10 E 2.415,1.71 2.571,1.891 0.156,0.181 10 5 3.121,0.419 3.277,0.601 0.156,0.181 10 6 3.42,0.529 3.622,0.710 0.202,0.181 10 ES 3.304,2.905 4.798,3.120 1.494,0.215 10 Windshield Wiper ECU 2.417,0.402 2.572,0.584 0.156,0.181 10 2 2.533,0.402 2.689,0.584 0.156,0.181 10 *1 2.485,0.202 2.641,0.383 0.156,0.181 10 *2 2.392,1.88 2.563,2.061 0.171,0.181 10 10 2.537,1.873 2.693,2.054 0.156,0.181 10 *1 2.498,1.706 2.654,1.887 0.156,0.181 10 *2 1.165,2.789 1.429,2.970 0.264,0.181 10 E16 3.289,2.769 3.553,2.951 0.264,0.181 10 E83 0.117,3.136 1.037,3.318 0.920,0.181 10 *1: for LH Side 0.106,3.431 1.049,3.612 0.943,0.181 10 *2: for RH Side 4.267,0.42 4.538,0.601 0.272,0.181 10 IG1l 4.606,0.299 4.762,0.480 0.156,0.181 10 5

PROCEDURE

1.INSPECT FUSE (ECU-IG No. 1)
a.

Remove the ECU-IG No. 1 fuse from the cowl side junction block LH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ECU-IG No. 1 fuse Always Below 1 Ω




OK

2.READ VALUE USING INTELLIGENT TESTER (WINDSHIELD WIPER SWITCH)

NG

REPLACE FUSE

2.READ VALUE USING INTELLIGENT TESTER (WINDSHIELD WIPER SWITCH)
a.

Check the Data List for proper functioning of the windshield wiper switch.

Combination Switch
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
F Wiper LO SW Front wiper LO switch / ON or OFF ON: Front wiper switch in LO
OFF: Front wiper switch not in LO
-
F Wiper HI SW Front wiper HI switch / ON or OFF ON: Front wiper switch in HI
OFF: Front wiper switch not in HI
-
F Wiper AUTO SW Front wiper AUTO switch / ON or OFF ON: Front wiper switch in AUTO
OFF: Front wiper switch not in AUTO
-
F Wiper MIST SW Front wiper MIST switch / ON or OFF ON: Front wiper switch in MIST
OFF: Front wiper switch not in MIST
-
F Washer SW Front washer switch / ON or OFF ON: Front washer switch on
OFF: Front washer switch off
-

OK:

The display is as specified in the normal condition.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER SWITCH - BATTERY AND BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER SWITCH - BATTERY AND BODY GROUND)
a.
U165933E02
1.052,0.802 1.75,1.177 true 0.938,1.469 1.292,1.5 true 1.031,1.031 1.5,1.26 true 2.021,1.458 2.365,1.521 true 0.24,0.042 2.635,0.49 2.396,0.448 10 false Front view of wire harness connector: (to Windshield Wiper Switch) 0.729,0.708 1.219,0.927 0.49,0.219 10 false +B*2 0.667,1.385 1.135,1.615 0.469,0.229 10 false E*2 2.406,1.063 2.719,1.24 0.313,0.177 10 false E16 0.667,0.938 1.104,1.156 0.438,0.219 10 false +B*1 2.365,1.427 2.688,1.646 0.323,0.219 10 false E*1 0.042,1.885 0.99,2.063 0.948,0.177 10 false *1: for RH Side 1.125,1.875 2.073,2.052 0.948,0.177 10 false *2: for LH Side

Disconnect the E16 switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LH Side
Tester Connection Switch Condition Specified Condition
E16-2 (+B) - Body ground Engine switch on (IG) 11 to 14 V
E16-2 (+B) - Body ground Engine switch off Below 1 V

for RH Side
Tester Connection Switch Condition Specified Condition
E16-3 (+B) - Body ground Engine switch on (IG) 11 to 14 V
E16-3 (+B) - Body ground Engine switch off Below 1 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH Side
Tester Connection Condition Specified Condition
E16-10 (E) - Body ground Always Below 1 Ω

for RH Side
Tester Connection Condition Specified Condition
E16-5 (E) - Body ground Always Below 1 Ω




OK

REPLACE WINDSHIELD WIPER SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR