Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM(w/ Rain Sensor) › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052854 WIPER / WASHER _0255769 WIPER AND WASHER SYSTEM(w/ Rain Sensor) J

WIPER / WASHER  WIPER AND WASHER SYSTEM(w/ Rain Sensor)  Headlight Cleaner Switch Circuit  


DESCRIPTION

This circuit detects the conditions of the headlight cleaner switch.

·

Headlight cleaner switch signal

·

Headlight operating signal

·

Daytime running light operating signal


WIRING DIAGRAM

E158184E07
5.627,1.343 5.783,1.525 0.156,0.181 10 5 5.883,1.459 6.039,1.640 0.156,0.181 10 L 5.883,0.906 6.039,1.087 0.156,0.181 10 B 5.644,0.817 5.800,0.998 0.156,0.181 10 8 5.824,5.313 6.829,5.494 1.005,0.181 10 Main Body ECU 5.724,3.524 5.896,3.705 0.171,0.181 10 23 6.046,3.698 6.441,3.879 0.395,0.181 10 HRLY 0.233,2.35 1.605,2.705 1.373,0.354 10 Headlight Cleaner Control Relay 1.065,0.841 1.221,1.023 0.156,0.181 10 2 0.843,0.936 0.999,1.117 0.156,0.181 10 H 5.433,1.843 5.653,2.024 0.220,0.181 10 G4 5.425,2.028 7.119,2.209 1.694,0.181 10 Headlight Cleaner Switch 5.833,5.131 6.028,5.312 0.195,0.181 10 2D

PROCEDURE

1.CHECK HEADLIGHT ASSEMBLY (LO BEAM)
a.

Check that the headlights illuminate in LO beam.

OK:

Headlights illuminate in LO beam




OK

2.INSPECT HEADLIGHT CLEANER SWITCH ASSEMBLY

NG

2.INSPECT HEADLIGHT CLEANER SWITCH ASSEMBLY
a.
E157699E02
0.998,3.06 1.145,3.197 0.147,0.137 10 B 2.302,3.06 2.473,3.197 0.171,0.137 10 L 1.462,2.834 1.127,3.06 false 1.961,2.825 2.242,3.06 false 0.179,1.427 2.679,1.845 2.500,0.419 10 Component without harness connected: (Headlight Cleaner Switch Assembly)

Disconnect the G4 cleaner switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
8 (B) - 5 (L) Headlight cleaner switch off 10 kΩ or higher
8 (B) - 5 (L) Headlight cleaner switch on Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT CLEANER SWITCH ASSEMBLY - HEADLIGHT CLEANER CONTROL RELAY AND MAIN BODY ECU)

NG

REPLACE HEADLIGHT CLEANER SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT CLEANER SWITCH ASSEMBLY - HEADLIGHT CLEANER CONTROL RELAY AND MAIN BODY ECU)
a.

Disconnect the headlight cleaner control relay connector.

E349777E01
2.24,1.406 2.635,1.656 0.396,0.25 4.573,1.625 4.969,1.875 0.396,0.25 1.042,1.552 0.552,1.198 false 4.167,1.854 3.792,1.75 false 2.979,2.156 3.26,1.771 false 5.583,1.688 5.99,1.323 false 0.031,0.135 2.427,0.802 2.396,0.667 10 false Front view of wire harness connector: (to Headlight Cleaner Control Relay) 2.448,0.115 4.844,0.781 2.396,0.667 10 false Front view of wire harness connector: (to Headlight Cleaner Switch) 4.76,0.135 7.156,0.802 2.396,0.667 10 false Front view of wire harness connector: (to Main Body ECU [Cowl Side Junction Block LH]) 2.333,1.438 2.625,1.646 0.292,0.208 10 false G4 0.469,1 0.625,1.198 0.156,0.198 10 false H 2.844,2.125 3,2.323 0.156,0.198 10 false L 4.198,1.813 4.354,2.01 0.156,0.198 10 false B 4.677,1.656 4.906,1.833 0.229,0.177 10 false 2D 5.813,1.115 6.281,1.292 0.469,0.177 10 false HRLY


b.

Disconnect the G4 switch connector.


c.

Disconnect the 2D main body ECU connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (H) - G4-8 (B) Always Below 1 Ω
G4-5 (L) - 2D-23 (HRLY)
2 (H) - Body ground Always 10 kΩ or higher
G4-8 (B) - Body ground
G4-5 (L) - Body ground
2D-23 (HRLY) - Body ground




OK

REPLACE HEADLIGHT CLEANER CONTROL RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR