Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM(w/ Rain Sensor) › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052854 WIPER / WASHER _0255769 WIPER AND WASHER SYSTEM(w/ Rain Sensor) J

WIPER / WASHER  WIPER AND WASHER SYSTEM(w/ Rain Sensor)  Headlight Cleaner Motor and Relay Circuit  


DESCRIPTION

This circuit provides power to the headlight cleaner control relay.

The headlight cleaner control relay sends the signal from the switch, etc. to the headlight cleaner motor to operate the headlight cleaner system.

WIRING DIAGRAM

E158383E10
5.056,2.874 7.082,3.025 2.026,0.151 10 Headlight Cleaner Control Relay 5.752,0.394 6.111,0.615 0.360,0.221 10 PB 5.761,1.767 6.028,1.914 0.267,0.147 10 IG 5.752,2.202 5.968,2.371 0.216,0.170 10 E 5.551,0.525 5.767,0.695 0.216,0.170 10 6 5.551,1.87 5.767,2.040 0.216,0.170 10 3 5.551,2.318 5.767,2.488 0.216,0.170 10 4 3.711,0.33 3.922,0.500 0.211,0.170 10 1 4.54,0.33 4.751,0.500 0.211,0.170 10 2 1.016,0.385 1.816,0.573 0.799,0.188 10 from Battery 0.501,1.751 1.869,1.939 1.369,0.188 10 from IG1 NO.1 Relay 2.425,0.598 3.075,0.779 0.650,0.181 10 H-LP CLR 4.309,1.919 5.183,2.100 0.874,0.181 10 ECU-IG No.1 3.343,0.775 4.956,1.247 1.614,0.472 10 Headlight Cleaner Motor and Pump Assembly

PROCEDURE

1.INSPECT FUSE (ECU-IG No.1, H-LP CLR)
a.

Remove the ECU-IG No.1 fuse from the main body ECU.


b.

Remove the H-LP CLR fuse from the engine junction block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ECU-IG No.1 fuse Always Below 1 Ω
H-LP CLR fuse




OK

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (HEADLIGHT CLEANER)

NG

REPLACE FUSE (ECU-IG No. 1, H-LP CLR)

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (HEADLIGHT CLEANER)
a.

Using the intelligent tester, perform the Active Test (See page Vehicle Exterior>WIPER / WASHER>WIPER AND WASHER SYSTEM(w/ Rain Sensor)>DATA LIST / ACTIVE TEST).

Main Body
Tester Display Test Part Control Range Diagnostic Note
Head Light Cleaner Headlight cleaner operation ON / OFF -

HINT:

for Headlight Cleaner System with Wiper Washer Function

The headlight cleaner system only operates when the windshield wiper switch assembly (front washer switch) is turned on the first time. After that, the headlight cleaner system cannot be operated with the windshield wiper switch assembly (front washer switch) until the engine switch is turned off and then turned to on (IG).


OK:

Headlight cleaner operates.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT CLEANER CONTROL RELAY - BATTERY AND BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (HEADLIGHT CLEANER CONTROL RELAY - BATTERY AND BODY GROUND)
a.
E139345E06
0.255,0 2.580,0.348 2.325,0.348 10 Front view of wire harness connector: (to Headlight Cleaner Control Relay) 2.374,1.127 2.800,1.309 0.426,0.181 10 IG 1.974,1.185 2.341,1.185 false 0.862,1.72 1.018,1.903 0.156,0.183 10 E 1.51,1.484 1.013,1.819 false

Disconnect the headlight cleaner control relay connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
3 (IG) - Body ground Engine switch on (IG) 11 to 14 V
3 (IG) - Body ground Engine switch off Below 1 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
4 (E) - Body ground Engine switch on (IG) Below 1 Ω




OK

4.INSPECT HEADLIGHT CLEANER MOTOR AND PUMP ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT HEADLIGHT CLEANER MOTOR AND PUMP ASSEMBLY
a.
B172829E02
0.06,0 2.567,0.592 2.507,0.592 10 Component without harness connected: (Headlight Cleaner Motor and Pump Assembly)

Remove the headlight cleaner motor and pump assembly (See page Vehicle Exterior>WIPER / WASHER>HEADLIGHT CLEANER MOTOR>REMOVAL).


b.

Apply battery voltage to the headlight cleaner motor and check the operation of the headlight cleaner motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 2
Headlight cleaner motor operation is normal




OK

5.CHECK HARNESS AND CONNECTOR (CLEANER MOTOR - CONTROL RELAY AND BATTERY)

NG

REPLACE HEADLIGHT CLEANER MOTOR AND PUMP ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (CLEANER MOTOR - CONTROL RELAY AND BATTERY)
a.
E125074E09
2.275,4.365 2.500,4.523 0.225,0.158 10 PB 1.988,3.849 2.353,4.322 false 0.179,0.101 2.504,0.625 2.325,0.524 10 Front view of wire harness connector: (to Headlight Cleaner Motor and Pump Assembly) 0.196,2.336 2.521,2.684 2.325,0.348 10 Front view of wire harness connector: (to Headlight Cleaner Control Relay)

Disconnect the headlight cleaner motor and pump assembly connector.


b.

Disconnect the headlight cleaner control relay connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1 - Body ground Always 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - 6 (PB) Always Below 1 Ω
2 - Body ground Always 10 kΩ or higher




OK

6.REPLACE HEADLIGHT CLEANER CONTROL RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE HEADLIGHT CLEANER CONTROL RELAY
a.

Temporarily replace the headlight cleaner control relay with a new or normally functioning one (See page Vehicle Exterior>WIPER / WASHER>RELAY(w/ Headlight Cleaner System)>REMOVAL).


b.

Check that the headlight cleaner system operates normally.

OK:

Headlight cleaner system operates normally.


HINT:

for Headlight Cleaner System with Wiper Washer Function

The headlight cleaner system only operates when the windshield wiper switch assembly (front washer switch) is turned on the first time. After that, the headlight cleaner system cannot be operated with the windshield wiper switch assembly (front washer switch) until the engine switch is turned off and then turned to on (IG).




OK

END (HEADLIGHT CLEANER CONTROL RELAY IS DEFECTIVE)

NG

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE