Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM(w/o Rain Sensor)
RM2660E _59 Vehicle Exterior _052854 WIPER / WASHER _0255770 WIPER AND WASHER SYSTEM(w/o Rain Sensor) D

WIPER / WASHER  WIPER AND WASHER SYSTEM(w/o Rain Sensor)  SYSTEM DESCRIPTION  


WASHER LINKED OPERATION


a.

This system operates the front wipers at low speed immediately after a jet of washer fluid when the front washer switch is turned on for 0.3 seconds or more. The system operates the front wipers at low speed for approximately 2.2 seconds and then stops operation when the washer switch is turned on for 1.5 seconds or more.



INTERMITTENT OPERATION


a.

The system operates the front wipers once in approximately 1.6 to 10.7 seconds when the front wiper switch is turned to the INT position. The intermittent time can be adjusted from 1.6 to 10.7 seconds by using the intermittent time adjust dial.


b.

If the front wiper switch is turned to the INT position, current flows from the already charged capacitor C1 through terminals INT1 and INT2 of the front wiper switch to Tr1 (transistor). When Tr1 turns on, current flows from terminal +S of the front wiper switch to terminal +1 of the front wiper switch, to terminal +1 of the wiper motor, to the wiper motor and finally to ground, causing the wiper motor to operate. At the same time, current flows from capacitor C1 to terminal INT1 of the front wiper switch and then INT2. When the current flow from capacitor C1 ends, Tr1 turns off to stop the relay contact point and halt the wiper motor.

E252232E02
2.979,4.198 4.625,4.438 1.646,0.24 10 false Windshield Wiper Switch 0.229,0.844 1.031,1.26 0.802,0.417 10 false Front Wiper Switch 4.708,1.5 5.594,1.906 0.885,0.406 10 false Front Washer Switch 0.552,2.896 1.427,3.583 0.875,0.688 10 false Front Wiper Relay Circuit 1.542,0.688 1.75,0.854 0.208,0.167 10 false +B 1.917,0.688 2.125,0.854 0.208,0.167 10 false +2 2.271,0.688 2.458,0.844 0.188,0.156 10 false +1 2.635,0.688 2.844,0.844 0.208,0.156 10 false +S 2.948,0.688 3.281,0.854 0.333,0.167 10 false INT1 3.323,0.688 3.677,0.854 0.354,0.167 10 false INT2 3.74,0.688 3.958,0.844 0.219,0.156 10 false B1 1.094,0.885 1.479,1.031 0.385,0.146 10 false MIST 1.104,1.063 1.469,1.24 0.365,0.177 10 false OFF 1.135,1.25 1.406,1.438 0.271,0.188 10 false INT 1.146,1.427 1.396,1.604 0.25,0.177 10 false LO 1.156,1.625 1.313,1.771 0.156,0.146 10 false HI 5.604,0.844 5.885,1.021 0.281,0.177 10 false W 5.917,0.844 6.156,0.979 0.24,0.135 10 false EW 5.198,1.031 5.51,1.208 0.313,0.177 10 false OFF 5.229,1.208 5.5,1.375 0.271,0.167 10 false ON 0.115,0.021 1.135,0.219 1.021,0.198 12 false Front Wiper: 4.01,5.198 5.354,5.375 1.344,0.177 10 false Front Washer Motor 3.26,6 4.5,6.208 1.24,0.208 10 false Front Wiper Motor 2.156,5.729 2.385,5.885 0.229,0.156 10 false LO 2.063,6.083 2.229,6.25 0.167,0.167 10 false HI 1.135,5.115 1.479,5.292 0.344,0.177 10 false WSH 1.115,5.375 1.583,5.552 0.469,0.177 10 false WIPER 0.365,5.771 1.698,5.948 1.333,0.177 10 false from IG1 NO.3 Relay 3.042,3.479 3.24,3.625 0.198,0.146 10 false C1 5.167,3.458 5.406,3.635 0.24,0.177 10 false C2 4.865,2.885 5.135,3.031 0.271,0.146 10 false Tr2 4.24,3.125 4.51,3.271 0.271,0.146 10 false Tr1

When the relay contact point turns off, capacitor C1 begins to charge again and Tr1 remains off until charging has been completed. This period corresponds to the intermittent time. When capacitor C1 is fully charged, Tr1 turns on and then the relay contact point turns on, causing the motor to operate again. This cycle is the intermittent operation.

The intermittent time can be adjusted by using the intermittent time adjust dial (variable resistor) to change the charge time of capacitor C1.



REAR WIPER INTERMITTENT OPERATION (w/ Rear Wiper)


a.

When the rear wiper switch is turned to the INT position, current flows from the capacitor of the intermittent operation control circuit to turn on the transistor. Current flows from terminal +B of the rear wiper relay, to the relay coil, to the transistor, to terminal C1 of the rear wiper relay, to terminal C1R of the rear wiper control switch and finally to ground, causing the relay contact point to turn on.

E252231E03
0.896,4.01 2.49,4.229 1.594,0.219 10 false Rear Wiper Relay Circuit 1.938,0.594 3.073,0.813 1.135,0.219 10 false Rear Wiper Motor 3.604,4.042 4.927,4.615 1.323,0.573 10 false Windshield Wiper Switch Assembly (Rear Wiper Switch) 0.896,4.458 2.781,4.677 1.885,0.219 10 false Rear Wiper Motor Assembly 3.667,1.5 4.521,2.167 0.854,0.667 10 false Rear Washer Motor and Pump Assembly 5.198,1.5 6.063,1.677 0.865,0.177 10 false RR WIPER 4.49,2.906 4.823,3.083 0.333,0.177 10 false WR 5.25,2.917 5.646,3.094 0.396,0.177 10 false +1R 4.854,2.917 5.25,3.094 0.396,0.177 10 false C1R 5.604,2.917 5.938,3.094 0.333,0.177 10 false EW 1.75,1.125 1.979,1.302 0.229,0.177 10 false +1 1.427,1.125 1.656,1.302 0.229,0.177 10 false +B 1.219,1.135 1.385,1.313 0.167,0.177 10 false S 2.417,1.708 2.646,1.885 0.229,0.177 10 false +B 2.385,2.125 2.615,2.302 0.229,0.177 10 false SM 2.396,1.906 2.625,2.083 0.229,0.177 10 false LM 0.802,1.146 0.969,1.323 0.167,0.177 10 false E 0.823,3.698 0.938,3.875 0.115,0.177 10 false E 3.948,3.094 4.458,3.26 0.51,0.167 10 false WASH1 4.052,3.271 4.365,3.438 0.313,0.167 10 false OFF 4.073,3.469 4.333,3.635 0.26,0.167 10 false INT 4.073,3.635 4.333,3.802 0.26,0.167 10 false ON 3.948,3.823 4.458,3.99 0.51,0.167 10 false WASH2 0.094,0 3.792,0.208 3.698,0.208 12 false Rear Wiper (for Double Swing Out Type): 2.396,3.531 2.625,3.708 0.229,0.177 10 false C1 5.75,2.302 7.104,2.49 1.354,0.188 10 false from IG1 NO.3 Relay

E286271E05
4.625,3.49 5.146,3.635 0.521,0.146 10 false Washer 4.542,1.24 5.26,1.385 0.719,0.146 10 false RR WIPER 5.792,1.125 7.135,1.271 1.344,0.146 10 false from IG1 NO.3 Relay 0.115,0.104 2.365,0.354 2.25,0.25 12 false Rear Wiper: 4.323,2.542 6.875,2.885 2.552,0.344 10 false Rear Washer Motor and Pump Assembly 0.75,4.635 2.635,4.833 1.885,0.198 10 false Rear Wiper Relay Circuit 0.781,5.063 2.573,5.26 1.792,0.198 10 false Rear Wiper Motor Assembly 4.198,4.417 5.76,4.76 1.563,0.344 10 false Windshield Wiper Switch Assembly 5.667,3.302 5.958,3.448 0.292,0.146 10 false +1R 6.042,3.302 6.344,3.448 0.302,0.146 10 false C1R 5.323,3.313 5.583,3.458 0.26,0.146 10 false WR 6.427,3.313 6.677,3.458 0.25,0.146 10 false EW 4.74,3.667 5.042,3.813 0.302,0.146 10 false OFF 4.76,3.844 5.01,3.99 0.25,0.146 10 false INT 4.5,4.208 5.271,4.354 0.771,0.146 10 false On+Washer 4.771,4.021 5,4.167 0.229,0.146 10 false ON 2.719,2.042 2.948,2.188 0.229,0.146 10 false +B 2.167,2.052 2.375,2.198 0.208,0.146 10 false +B 1.219,1.479 1.427,1.625 0.208,0.146 10 false +B 1.5,1.479 1.708,1.625 0.208,0.146 10 false +1 2.719,3.219 2.948,3.365 0.229,0.146 10 false LS 2.135,2.26 2.365,2.406 0.229,0.146 10 false LM 2.135,2.49 2.365,2.635 0.229,0.146 10 false SM 2.719,3.438 2.948,3.583 0.229,0.146 10 false C1 2.75,3.667 2.948,3.813 0.198,0.146 10 false W 0.333,0.813 0.531,0.958 0.198,0.146 10 false E 1.021,1.479 1.219,1.625 0.198,0.146 10 false S 1.719,0.969 3.604,1.167 1.885,0.198 10 false Rear Wiper Motor

When the relay contact point turns on, current flows from terminal +B of the rear wiper relay to the relay contact point, to terminal LM of the rear wiper relay, to terminal +1 of the rear wiper motor, to the rear wiper motor and finally to ground, causing the rear wiper motor to operate. The transistor turns off immediately after the rear wiper motor operation as the current flow from the capacitor ends, causing the relay contact point to turn off.

Even when the relay contact point turns off, current flows from terminal +B of the rear wiper motor, to the relay contact point in the rear wiper motor, to terminal S of the rear wiper motor, to terminal SM of the rear wiper relay, to the contact point of the rear wiper relay, to terminal LM of the rear wiper relay, to terminal +1 of the rear wiper motor and finally to ground until the rear wiper motor stops at the automatic stop position, causing the rear wiper motor to operate. Then the rear wiper motor stops at the automatic stop position as the relay contact point in the rear wiper motor turns off.

The capacitor in the intermittent operation control circuit is charged in approximately 12 seconds after the current flow ends. After the charge is completed, current starts flowing again to turn on the transistor, causing the relay contact point to turn on.

This cycle of current flow and charging described above is the intermittent operation.



HEADLIGHT CLEANER SYSTEM (w/ Headlight Cleaner System)


a.

The headlight cleaner system operates when the headlights are on and the headlight cleaner switch is pushed on. It also operates when the headlights are on and the front wiper washer system is operating.


b.

The headlight cleaner system also operates when the front washer switch is first operated with the headlights on after the ignition switch is turned to ON*.

*: w/ Headlight Auto Leveling




WASHER NOZZLE HEATER SYSTEM (w/ Washer Nozzle Heater System)


a.

The washer nozzle heater system operates when the ambient temperature drops to 5°C (41°F) or less while the ignition switch is ON.


b.

The washer nozzle heater system stops operating when the ignition switch is turned off, or when the ambient temperature reaches 6°C (42°F) or higher while the ignition switch is ON.