Home › Vehicle Exterior › WIPER / WASHER › WIPER SWITCH › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052854 WIPER / WASHER _0255772 WIPER SWITCH G

WIPER / WASHER  WIPER SWITCH  INSPECTION  


PROCEDURE

Hide 84650 1.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (for RH Side)

a.
U164035E02
2.104,2.896 2.01,3.271 false 2.188,3.281 2.563,2.906 false 1.729,2.875 1.615,3.271 false 1.333,2.865 1.417,3.271 false 1.188,3.292 0.906,2.885 false 0.99,3.302 0.604,2.885 false 2.021,4.021 2.302,4.167 0.281,0.146 10 false E15 1.146,4.021 1.427,4.188 0.281,0.167 10 false E16 2.49,2.698 2.76,2.875 0.271,0.177 10 false EW 2.01,2.667 2.281,2.833 0.271,0.167 10 false WF 0.438,2.688 0.677,2.854 0.24,0.167 10 false +2 0.792,2.677 1.031,2.844 0.24,0.167 10 false +1 1.656,2.667 1.896,2.823 0.24,0.156 10 false +S 1.229,2.656 1.469,2.823 0.24,0.167 10 false +B 0.219,1.688 2.771,2.198 2.552,0.51 10 false Component without harness connected: (Windshield Wiper Switch Assembly)

Check the windshield wiper switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Front Wiper Switch (w/o Rain Sensor)
Tester Connection Switch Condition Specified Condition
E16-1 (+S) - E16-3 (+1) INT Below 1 Ω
OFF
E16-2 (+B) - E16-3 (+1) MIST
LO
E16-2 (+B) - E16-4 (+2) HI


If the result is not as specified, replace the windshield wiper switch assembly.

Standard Resistance:
Front Wiper Switch (w/ Rain Sensor)
Tester Connection Switch Condition Specified Condition
E16-1 (+S) - E16-3 (+1) AUTO Below 1 Ω
OFF
E16-2 (+B) - E16-3 (+1) MIST
LO
E16-2 (+B) - E16-4 (+2) HI


If the result is not as specified, replace the windshield wiper switch assembly.



b.

Check the front washer switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E15-2 (EW) - E15-3 (WF) On Below 1 Ω
Off 10 kΩ or higher


If the result is not as specified, replace the windshield wiper switch assembly.



c.

Check the intermittent operation.

i.

Connect the voltmeter positive (+) lead to terminal E16-3 (+1) and the negative (-) lead to terminal E15-2 (EW).


ii.

Connect the battery positive (+) lead to terminal E16-2 (+B) and the negative (-) lead to terminal E15-2 (EW) and E16-1 (+S).


iii.

Turn the wiper switch to the INT position.


iv.

Connect the battery positive (+) lead to terminal E16-1 (+S) for 5 seconds.


v.

Connect the battery negative (-) lead to terminal E16-1 (+S). Operate the intermittent wiper relay and check the voltage between terminals E16-3 (+1) and E15-2 (EW).

Standard Voltage:

Refer to the illustration below.


U165964E01
0.081,1.562 1.980,1.889 1.899,0.327 10 Voltage between terminals E16-3 (+1) and E15-2 (EW) 1.682,1.173 2.402,1.324 0.719,0.151 10 11 to 14 V 2.148,1.651 2.422,1.807 0.274,0.156 10 0 V 2.432,2.086 3.497,2.250 1.064,0.164 10 1.6 +/-1 second 2.754,0.454 4.743,0.804 1.989,0.350 10 FAST: Connect battery negative (-) lead to terminal E16-1 (+S) 4.847,0.454 7.120,0.804 2.273,0.351 10 SLOW: Connect battery negative (-) lead to terminal E16-1 (+S) 4.573,2.078 5.766,2.233 1.193,0.155 10 10.7 +/-5 seconds 4.761,1.969 4.761,1.758 false 3.122,1.758 3.122,1.969 false 4.761,1.967 5.56,1.967 false 2.73,1.969 3.122,1.969 false 2.73,2.039 2.73,1.969 false 2.73,1.969 2.73,1.758 false 2.73,0.918 2.73,1.266 false 3.122,2.039 3.122,1.969 false 3.122,1.969 3.122,1.758 false 4.761,1.969 4.761,1.758 false 4.759,0.918 4.759,1.266 false 4.761,2.039 4.761,1.969 false 5.56,2.039 5.56,1.969 false 5.56,1.969 5.56,1.758 false 0.04,0.007 2.439,0.239 2.399,0.232 12 w/ Intermittent Time Adjust Dial:

B278090E09
0.083,0.625 2.021,1.083 1.938,0.458 10 false Voltage between terminals E16-3 (+1) and E15-2 (EW) 3.865,0 5.948,0.458 2.083,0.458 10 false Connect battery negative (-) lead to terminal E16-1 (+S) 3.698,1.344 4.844,1.604 1.146,0.26 10 false 3.3 +/- 1 second 2.698,0.479 3.49,0.74 0.792,0.26 10 false 11 to 14 V 3.115,0.938 3.438,1.198 0.323,0.26 10 false 0 V 0.042,0.052 2.563,0.292 2.521,0.24 12 false w/o Intermittent Time Adjust Dial:

If the result is not as specified, replace the switch assembly.



d.

Check the front washer operation.

i.

Turn the wiper switch OFF.


ii.

Connect the battery positive (+) lead to terminal E16-2 (+B) and the negative (-) lead to terminals E16-1 (+S) and E15-2 (EW).


iii.

Connect the voltmeter positive (+) lead to E16-3 (+1) and the negative (-) lead to terminal E15-2 (EW).


iv.

Turn the washer switch ON and OFF, and check the voltage between terminals E16-3 (+1) and E15-2 (EW).

OK:

Refer to the illustration below.


E157493E10
0.811,0.928 2.779,1.422 1.968,0.494 10 Voltage between terminals E16-3 (+1) and E15-2 (EW) 1.829,0.41 2.784,0.566 0.955,0.156 10 Washer Switch 3.417,1.173 3.781,1.329 0.364,0.156 10 0 V 3.137,0.902 3.827,1.044 0.691,0.142 10 11 to 14 V 2.819,1.482 4.545,1.624 1.725,0.142 10 Approximately 0.3 seconds 5.029,0.077 6.755,0.219 1.725,0.142 10 Approximately 1.5 seconds 4.671,1.489 6.396,1.631 1.725,0.142 10 Approximately 2.2 seconds 4.034,1.362 3.991,1.475 false 4.692,1.355 4.839,1.468 false 3.417,0.571 3.781,0.727 0.364,0.156 10 OFF 3.48,0.286 3.754,0.442 0.274,0.156 10 ON 5,0.149 4.429,0.149 4.429,0.149 4.228,0.268 false 0.066,0.038 2.537,0.352 2.471,0.313 12 w/ Multi-information Display:

E157493E08
0.643,0.928 2.611,1.422 1.968,0.494 10 Voltage between terminals E16-3 (+1) and E15-2 (EW) 1.829,0.41 2.784,0.566 0.955,0.156 10 Washer Switch 3.417,1.173 3.781,1.329 0.364,0.156 10 0 V 3.137,0.902 3.827,1.044 0.691,0.142 10 11 to 14 V 2.819,1.482 4.545,1.624 1.725,0.142 10 Approximately 0.5 seconds 5.029,0.077 6.755,0.219 1.725,0.142 10 Approximately 1.5 seconds 4.671,1.489 6.396,1.631 1.725,0.142 10 Approximately 2.2 seconds 4.033,1.362 3.991,1.475 false 4.692,1.355 4.839,1.468 false 3.417,0.571 3.781,0.727 0.364,0.156 10 OFF 3.48,0.286 3.754,0.442 0.274,0.156 10 ON 5,0.149 4.429,0.149 4.429,0.149 4.228,0.268 false 0.062,0.034 2.384,0.310 2.323,0.276 12 w/o Multi-information Display:

If the result is not as specified, replace the switch assembly.



e.
U164034E02
2.302,3.271 2.792,3.01 false 1.583,3.594 1.479,4.021 false 2.01,3.604 2.094,4.01 false 2.469,4.021 2.146,3.563 false 2.969,3.344 3.25,3.49 0.281,0.146 10 false E15 0.26,3.333 0.542,3.5 0.281,0.167 10 false E16 0.292,1.74 2.844,2.25 2.552,0.51 10 false Component without harness connected: (Windshield Wiper Switch Assembly) 2.875,2.833 3.146,3.01 0.271,0.177 10 false EW 1.344,4.052 1.635,4.219 0.292,0.167 10 false WR 2.5,4.042 2.865,4.198 0.365,0.156 10 false C1R 1.979,4.052 2.302,4.208 0.323,0.156 10 false +1R

Check the rear wiper switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Rear Wiper Switch (w/ Rear Wiper Intermittent Function)
Tester Connection Switch Condition Specified Condition
E15-2 (EW) - E15-6 (C1R) LO Below 1 Ω
E15-2 (EW) - E15-7 (+1R) HI
E15-2 (EW) - E15-6 (C1R) OFF 10 kΩ or higher
E15-2 (EW) - E15-7 (+1R)


If the result is not as specified, replace the windshield wiper switch assembly.

Standard Resistance:
Rear Wiper Switch (w/o Rear Wiper Intermittent Function)
Tester Connection Switch Condition Specified Condition
E15-2 (EW) - E15-7 (+1R) ON Below 1 Ω
E15-2 (EW) - E15-7 (+1R) OFF 10 kΩ or higher


If the result is not as specified, replace the windshield wiper switch assembly.



f.

Check the rear washer switch.

i.

Measure the resistance of the switch.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E15-2 (EW) - E16-5 (WR) On Below 1 Ω
Off 10 kΩ or higher


If the result is not as specified, replace the windshield wiper switch assembly.



Hide 84650 2.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (for LH Side)

a.
U164122E02
1.344,3 1.438,3.375 false 1.25,3.365 0.875,2.99 false 1.719,2.979 1.833,3.375 false 2.146,2.979 2.042,3.375 false 2.25,3.375 2.531,2.969 false 2.479,3.375 2.854,2.958 false 0.271,3.396 0.552,3.542 0.281,0.146 10 false E15 2.969,3.365 3.25,3.531 0.281,0.167 10 false E16 0.292,1.667 2.844,2.177 2.552,0.51 10 false Component without harness connected: (Windshield Wiper Switch Assembly) 0.708,2.802 0.979,2.979 0.271,0.177 10 false EW 1.25,2.792 1.521,2.958 0.271,0.167 10 false WF 2.938,2.781 3.177,2.948 0.24,0.167 10 false +2 2.563,2.781 2.802,2.948 0.24,0.167 10 false +1 1.688,2.781 1.927,2.938 0.24,0.156 10 false +S 2.125,2.781 2.365,2.948 0.24,0.167 10 false +B

Check the windshield wiper switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Front Wiper Switch (w/o Rain Sensor)
Tester Connection Switch Condition Specified Condition
E16-4 (+S) - E16-2 (+1) INT Below 1 Ω
OFF
E16-3 (+B) - E16-2 (+1) MIST
LO
E16-3 (+B) - E16-1 (+2) HI


If the result is not as specified, replace the windshield wiper switch assembly.

Standard Resistance:
Front Wiper Switch (w/ Rain Sensor)
Tester Connection Switch Condition Specified Condition
E16-4 (+S) - E16-2 (+1) AUTO Below 1 Ω
OFF
E16-3 (+B) - E16-2 (+1) MIST
LO
E16-3 (+B) - E16-1 (+2) HI


If the result is not as specified, replace the windshield wiper switch assembly.



b.

Check the front washer switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E15-2 (EW) - E15-1 (WF) On Below 1 Ω
Off 10 kΩ or higher


If the result is not as specified, replace the windshield wiper switch assembly.



c.

Check the intermittent operation.

i.

Connect the voltmeter positive (+) lead to terminal E16-2 (+1) and the negative (-) lead to terminal E15-2 (EW).


ii.

Connect the battery positive (+) lead to terminal E16-3 (+B) and the negative (-) lead to terminal E15-2 (EW) and E16-4 (+S).


iii.

Turn the wiper switch to the INT position.


iv.

Connect the battery positive (+) lead to terminal E16-4 (+S) for 5 seconds.


v.

Connect the battery negative (-) lead to terminal E16-4 (+S). Operate the intermittent wiper relay and check the voltage between terminals E16-2 (+1) and E15-2 (EW).

Standard Voltage:

Refer to the illustration below.


U165965E01
0.081,1.562 1.980,1.889 1.899,0.327 10 Voltage between terminals E16-2 (+1) and E15-2 (EW) 1.682,1.173 2.402,1.324 0.719,0.151 10 11 to 14 V 2.148,1.651 2.422,1.807 0.274,0.156 10 0 V 2.432,2.086 3.497,2.250 1.064,0.164 10 1.6 +/-1 second 2.755,0.536 4.743,0.887 1.989,0.350 10 FAST: Connect battery negative (-) lead to terminal E16-4 (+S) 4.843,0.536 6.989,0.887 2.146,0.351 10 SLOW: Connect battery negative (-) lead to terminal E16-4 (+S) 4.573,2.078 5.766,2.233 1.193,0.155 10 10.7 +/-5 seconds 4.761,1.969 4.761,1.758 false 3.122,1.758 3.122,1.969 false 4.761,1.967 5.56,1.967 false 2.73,1.969 3.122,1.969 false 2.73,2.039 2.73,1.969 false 2.73,1.969 2.73,1.758 false 2.73,0.918 2.73,1.266 false 3.122,2.039 3.122,1.969 false 3.122,1.969 3.122,1.758 false 4.761,1.969 4.761,1.758 false 4.759,0.918 4.759,1.266 false 4.761,2.039 4.761,1.969 false 5.56,2.039 5.56,1.969 false 5.56,1.969 5.56,1.758 false 0.067,0.028 2.522,0.288 2.454,0.260 12 w/ Intermittent Time Adjust Dial:

B278090E10
0.083,0.552 1.813,1.031 1.729,0.479 10 false Voltage between terminals E16-2 (+1) and E15-2 (EW) 3.865,0.01 5.948,0.469 2.083,0.458 10 false Connect battery negative (-) lead to terminal E16-4 (+S) 3.698,1.323 4.844,1.583 1.146,0.26 10 false 3.3 +/- 1 second 2.688,0.479 3.479,0.74 0.792,0.26 10 false 11 to 14 V 3.135,0.969 3.458,1.229 0.323,0.26 10 false 0 V 0.042,0.031 2.563,0.271 2.521,0.24 12 false w/o Intermittent Time Adjust Dial:

If the result is not as specified, replace the switch assembly.



d.

Check the front washer operation.

i.

Turn the wiper switch OFF.


ii.

Connect the battery positive (+) lead to terminal E16-3 (+B) and the negative (-) lead to terminals E16-4 (+S) and E15-2 (EW).


iii.

Connect the voltmeter positive (+) lead to E16-2 (+1) and the negative (-) lead to terminal E15-2 (EW).


iv.

Turn the washer switch ON and OFF, and check the voltage between terminals E16-2 (+1) and E15-2 (EW).

OK:

Refer to the illustration below.


E157493E09
0.643,0.921 2.509,1.415 1.867,0.494 10 Voltage between terminals E16-2 (+1) and E15-2 (EW) 1.829,0.403 2.784,0.559 0.955,0.156 10 Washer Switch 3.417,1.166 3.781,1.322 0.364,0.156 10 0 V 3.137,0.896 3.827,1.037 0.691,0.142 10 11 to 14 V 2.819,1.474 4.545,1.616 1.725,0.142 10 Approximately 0.5 seconds 4.671,1.481 6.396,1.623 1.725,0.142 10 Approximately 2.2 seconds 4.034,1.355 3.991,1.467 false 4.692,1.348 4.839,1.46 false 3.417,0.564 3.781,0.720 0.364,0.156 10 OFF 3.48,0.279 3.754,0.435 0.274,0.156 10 ON 5.029,0.077 6.755,0.219 1.725,0.142 10 Approximately 1.5 seconds 5,0.149 4.429,0.149 4.429,0.149 4.228,0.268 false

If the result is not as specified, replace the windshield wiper switch assembly.



e.
U164123E02
1.25,3.385 0.76,3.135 false 1.844,3.708 1.958,4.135 false 1.438,3.708 1.354,4.115 false 1,4.146 1.323,3.688 false 0.25,3.396 0.531,3.542 0.281,0.146 10 false E15 2.969,3.365 3.25,3.531 0.281,0.167 10 false E16 0.292,1.74 2.844,2.25 2.552,0.51 10 false Component without harness connected: (Windshield Wiper Switch Assembly) 1.938,4.177 2.229,4.344 0.292,0.167 10 false WR 0.448,2.969 0.719,3.146 0.271,0.177 10 false EW 0.802,4.177 1.135,4.333 0.333,0.156 10 false C1R 1.25,4.177 1.573,4.333 0.323,0.156 10 false +1R

Check the rear wiper switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Rear Wiper Switch (w/ Rear Wiper Intermittent Function)
Tester Connection Switch Condition Specified Condition
E15-2 (EW) - E15-5 (C1R) LO Below 1 Ω
E15-2 (EW) - E15-4 (+1R) HI
E15-2 (EW) - E15-5 (C1R) OFF 10 kΩ or higher
E15-2 (EW) - E15-4 (+1R)


If the result is not as specified, replace the windshield wiper switch assembly.

Standard Resistance:
Rear Wiper Switch (w/o Rear Wiper Intermittent Function)
Tester Connection Switch Condition Specified Condition
E15-2 (EW) - E15-4 (+1R) ON Below 1 Ω
E15-2 (EW) - E15-4 (+1R) OFF 10 kΩ or higher


If the result is not as specified, replace the windshield wiper switch assembly.



f.

Check the rear washer switch.

i.

Measure the resistance of the switch.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E15-2 (EW) - E16-10 (WR) On Below 1 Ω
Off 10 kΩ or higher


If the result is not as specified, replace the windshield wiper switch assembly.