Home › Vehicle Exterior › WIPER / WASHER › REAR WIPER MOTOR › from 2015.08
RM2660E _59 Vehicle Exterior _052854 WIPER / WASHER _0255783 REAR WIPER MOTOR A

WIPER / WASHER  REAR WIPER MOTOR  INSTALLATION  


PROCEDURE

Hide 85110R 1.INSTALL REAR WIPER MOTOR ASSEMBLY

a.
B181333

Temporarily install the rear wiper motor assembly with the 3 bolts.


b.

Tighten the 3 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


c.

Connect the connector.


Hide 85143R 2.INSTALL REAR WIPER MOTOR GROMMET

a.
B186887E03
1.397,0.821 1.601,1.008 0.205,0.187 10 *a 1.637,0.723 1.586,0.847 1.586,0.847 1.919,0.724 false

Apply MP grease to the entire circumference of the lip portion of the rear wiper motor grommet.

Text in Illustration
*a Lip Portion

HINT:

Do not fill the hole with MP grease. Only apply MP grease to the grooves of the lip portion.



b.
E156014E04
0.953,0.108 1.173,0.273 0.221,0.165 10 *a 1.165,0.194 1.302,0.194 1.302,0.194 1.566,0.852 false

Install the rear wiper motor grommet as shown in the illustration.

Text in Illustration
*a Position Mark


Hide 3.INSTALL REAR WIPER ARM AND BLADE ASSEMBLY

a.
B408077E01
2.096,0.271 2.655,0.520 0.559,0.248 10 *a 2.027,0.374 1.827,0.374 1.827,0.374 1.46,1.429 false 2.365,2.849 2.924,3.098 0.559,0.248 10 *b 2.285,2.958 2.079,2.958 2.079,2.958 1.575,3.468 false

When reinstalling:

Text in Illustration
*a Rear Wiper Arm Serrations
*b Rear Wiper Motor Assembly Pivot Serrations

NOTICE:

Do not grind the rear wiper arm serrations.


i.

Clean the rear wiper arm serrations.


ii.

Clean the rear wiper motor assembly pivot serrations.



b.

Turn the engine switch on (IG).


c.

Operate the rear wiper motor assembly and stop at the automatic stop (park) position.


d.

Turn the engine switch off.


e.
E156015E07
1.271,0.198 2.031,0.198 2.031,0.198 3.01,1.531 false 1.01,0.094 1.302,0.313 0.292,0.219 10 true *a

Align the rear wiper arm and blade assembly as shown in the illustration and install it with the nut.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

HINT:

Hold the arm hinge by the hand when tightening the nut.


Text in Illustration
*a Defogger Line


f.

Operate the rear wiper motor assembly while spraying washer fluid on the glass. Make sure that the rear wipers function properly and the wipers do not come into contact with the vehicle body.


g.

Raise the rear wiper arm 2 times and check that the tip of the rear wiper blade is within the range shown in the illustration.


h.
B407871

Return the rear wiper arm head cap.


i.
B407872

Attach the 2 claws to install the rear wiper arm head cap.


Hide 85292A 4.INSTALL REAR WIPER ARM HEAD CAP

a.
B407870

Attach the 2 guides and temporarily install the rear wiper arm head cap.


b.
B407871

Return the rear wiper arm head cap.


c.
B407872

Attach the 2 claws to install the rear wiper arm head cap.


Hide 67935B 5.INSTALL BACK DOOR GARNISH

Hide 67938A 6.INSTALL BACK DOOR SIDE GARNISH LH

Hide 67937B 7.INSTALL BACK DOOR SIDE GARNISH RH

Hide 67939B 8.INSTALL CENTER BACK DOOR GARNISH