Home › Vehicle Exterior › WIPER / WASHER › FRONT WIPER MOTOR › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052854 WIPER / WASHER _0255784 FRONT WIPER MOTOR A

WIPER / WASHER  FRONT WIPER MOTOR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for LHD and RHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 85110 1.INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY

a.
E156196

Install the wiper motor with the 2 screws.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


b.

Apply MP grease to the crank arm pivot of the windshield wiper motor assembly.


c.
E156194

Install the wiper motor and link.


d.
E156195

Install the wiper motor and link.


e.
E161961E01
0.056,1.631 1.332,1.836 1.277,0.205 10 Wiper Motor Cover 0.732,1.553 0.732,1.393 0.732,1.393 1.029,1.079 false

Install the wiper motor cover with the clamp.


Hide 85160 2.INSTALL WINDSHIELD WIPER LINK ASSEMBLY

a.
B184646E04
2.604,0.063 2.833,0.354 0.229,0.292 10 true (1) 0.552,0.042 0.813,0.229 0.26,0.188 10 true (2) 0.354,1.052 0.583,1.333 0.229,0.281 10 true (3) 1.5,0.031 1.938,0.292 0.438,0.26 10 true Slide

Install the windshield wiper motor and link assembly with the 3 bolts and the pin as shown in the illustration.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


b.

Connect the connector.


Hide 55781E 3.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

a.
E156191

Push the ventilator louver in the direction indicated by the arrow in the illustration to attach the 17 claws and 2 clips and install the ventilator louver.


b.
E156188

Install the washer hose.


c.

w/ PTC Heater

i.

Connect the connector.



Hide 53383 4.INSTALL HOOD TO COWL TOP SEAL

a.
E156189

Attach the 12 clips and 4 clamps to install the hood to cowl top seal.


Hide 53883F 5.INSTALL FRONT FENDER MAIN SEAL LH

a.
B181061

Attach the 3 clips to install the fender main seal.


Hide 53882H 6.INSTALL FRONT FENDER MAIN SEAL RH

HINT:

Use the same procedure described for the LH side.


Hide 53292A 7.INSTALL UPPER RADIATOR SUPPORT SEAL

Hide 8.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 85221B 9.INSTALL FRONT WIPER ARM LH

a.
E156199E01
2.346,2.69 3.067,2.883 0.721,0.193 10 Wire Brush 2.124,2.804 2.32,2.804 false 1.717,4.157 3.094,4.361 1.377,0.204 10 Wiper Pivot Serration 1.852,1.252 1.379,2.187 false 2.58,4.091 2.58,3.541 2.58,3.541 1.953,3.206 false 0.483,2.133 1.860,2.337 1.377,0.204 10 Wiper Pivot Serration

Stop the wiper motor at the automatic stop position.


b.

Clean the wiper pivot serration with a wire brush.


c.
E157802E06
1.76,0.219 1.427,0.219 1.427,0.219 0.427,1.104 false 2.188,3.063 2.188,2.875 2.188,2.875 2.042,2.49 false 1.177,2.5 1.333,2.75 0.156,0.25 10 false A 1.802,0.135 2.813,0.385 1.01,0.25 10 false Moulding Edge 1.667,3.073 2.677,3.323 1.01,0.25 10 false Moulding Edge

Install the wiper arm and blade with the nut. Make sure that the wiper arm and blade comes to the position shown in the illustration.

Standard Measurement:
Position Specified Condition
A 16.8 to 36.8 mm (0.661 to 1.45 in.)


Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

HINT:

Hold down the wiper arm hinge with your hand while tightening the nut.



Hide 85211B 10.INSTALL FRONT WIPER ARM RH

a.
E156199E01
2.346,2.69 3.067,2.883 0.721,0.193 10 Wire Brush 2.124,2.804 2.32,2.804 false 1.717,4.157 3.094,4.361 1.377,0.204 10 Wiper Pivot Serration 1.852,1.252 1.379,2.187 false 2.58,4.091 2.58,3.541 2.58,3.541 1.953,3.206 false 0.483,2.133 1.860,2.337 1.377,0.204 10 Wiper Pivot Serration

Stop the wiper motor at the automatic stop position.


b.

Clean the wiper pivot serration with a wire brush.


c.
E157803E06
1.76,0.219 1.427,0.219 1.427,0.219 0.427,1.104 false 2.188,2.792 2.188,2.698 2.188,2.698 2.042,2.49 false 1.802,0.135 2.813,0.385 1.01,0.25 10 false Moulding Edge 1.667,2.771 2.677,3.021 1.01,0.25 10 false Moulding Edge 0.156,2.427 0.354,2.656 0.198,0.229 10 false B

Install the wiper arm and blade with the nut. Make sure that the wiper arm and blade comes to the position shown in the illustration.

Standard Measurement:
Position Specified Condition
B 20.0 to 40.0 mm (0.787 to 1.57 in.)


Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

HINT:

Hold down the wiper arm hinge with your hand while tightening the nut.



d.

Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and there is no interference with the vehicle body.


Hide 85292B 11.INSTALL FRONT WIPER ARM HEAD CAP

a.
B407913

Engage the 3 claws to install the front wiper arm head cap.

HINT:

Use the same procedure for the RH side and LH side.