Home › Vehicle Exterior › WIPER / WASHER › FRONT WIPER MOTOR
RM2660E _59 Vehicle Exterior _052854 WIPER / WASHER _0255784 FRONT WIPER MOTOR G

WIPER / WASHER  FRONT WIPER MOTOR  INSPECTION  


PROCEDURE

Hide 85110 1.INSPECT WINDSHIELD WIPER MOTOR ASSEMBLY (for LHD)

a.
E156197E05
2.063,2.111 2.452,1.692 false 1.112,2.987 1.487,2.627 false 1.323,2.102 0.914,1.721 false 1.745,2.083 1.746,1.533 false 2.318,2.959 1.954,2.621 false 1.678,1.286 1.834,1.467 0.156,0.181 10 B 2.504,1.528 2.679,1.710 0.175,0.181 10 +1 2.355,2.977 2.530,3.158 0.175,0.181 10 +2 0.71,1.54 0.996,1.721 0.285,0.181 10 +S 0.928,2.977 1.084,3.158 0.156,0.181 10 E 0.184,0.171 2.738,0.679 2.554,0.508 10 Component without harness connected: (Front Wiper Motor Assembly (LHD)) 1.433,1.788 1.5,1.815 0.068,0.027 1.907,1.794 1.974,1.823 0.067,0.029

Check the LO operation.

i.

Apply battery voltage to the front wiper motor and check the speed of the front wiper motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 1 (+1)
Battery negative (-) → Terminal 5 (E)
Motor operates at low speed


If the result is not as specified, replace the windshield wiper motor assembly.



b.

Check the HI operation.

i.

Apply battery voltage to the front wiper motor and check the speed of the front wiper motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 4 (+2)
Battery negative (-) → Terminal 5 (E)
Motor operates at high speed


If the result is not as specified, replace the windshield wiper motor assembly.



c.

Check the automatic stop operation.

i.

Connect the positive (+) battery lead to terminal 1 (+1) of the connector and the negative (-) battery lead to terminal 5 (E). With the motor operating at low speed (LO), disconnect terminal 1 (+1) to stop the wiper motor operation at any position other than the automatic stop position.


ii.

Using SST, connect terminals 3 (+S) and 1 (+1). Then connect the positive (+) battery lead to terminal 2 (B) of the connector to restart the motor operation at low speed (LO).

SST
09843-18040  


iii.

Check that the motor stops automatically at the automatic stop position.

OK:

Automatically stops.


If the result is not as specified, replace the windshield wiper motor assembly.



Hide 85110 2.INSPECT WINDSHIELD WIPER MOTOR ASSEMBLY (for RHD)

a.
E156197E06
2.063,2.111 2.452,1.692 false 1.112,2.987 1.487,2.627 false 1.323,2.102 0.914,1.721 false 1.745,2.083 1.746,1.533 false 2.318,2.959 1.954,2.621 false 1.678,1.286 1.834,1.467 0.156,0.181 10 B 0.86,2.96 1.035,3.142 0.175,0.181 10 +1 0.661,1.557 0.836,1.738 0.175,0.181 10 +2 2.409,1.523 2.632,1.704 0.223,0.181 10 +S 2.38,2.977 2.536,3.158 0.156,0.181 10 E 0.184,0.171 2.738,0.679 2.554,0.508 10 Component without harness connected: (Front Wiper Motor Assembly (RHD)) 1.433,1.788 1.5,1.815 0.068,0.027 1.907,1.794 1.974,1.823 0.067,0.029

Check the LO operation.

i.

Apply battery voltage to the front wiper motor and check the speed of the front wiper motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 5 (+1)
Battery negative (-) → Terminal 4 (E)
Motor operates at low speed


If the result is not as specified, replace the windshield wiper motor assembly.



b.

Check the HI operation.

i.

Apply battery voltage to the front wiper motor and check the speed of the front wiper motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 3 (+2)
Battery negative (-) → Terminal 4 (E)
Motor operates at high speed


If the result is not as specified, replace the windshield wiper motor assembly.



c.

Check the automatic stop operation.

i.

Connect the positive (+) battery lead to terminal 5 (+1) of the connector and the negative (-) battery lead to terminal 4 (E). With the motor operating at low speed (LO), disconnect terminal 5 (+1) to stop the wiper motor operation at any position other than the automatic stop position.


ii.

Using SST, connect terminals 1 (+S) and 5 (+1). Then connect the positive (+) battery lead to terminal 2 (B) of the connector to restart the motor operation at low speed (LO).

SST
09843-18040  


iii.

Check that the motor stops automatically at the automatic stop position.

OK:

Automatically stops.


If the result is not as specified, replace the windshield wiper motor assembly.