Home › Vehicle Exterior › WIPER / WASHER › FRONT WIPER MOTOR › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052854 WIPER / WASHER _0255784 FRONT WIPER MOTOR A

WIPER / WASHER  FRONT WIPER MOTOR  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for LHD and RHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 53292A 3.REMOVE UPPER RADIATOR SUPPORT SEAL

Hide 53883F 4.REMOVE FRONT FENDER MAIN SEAL LH

a.
B181061

Using a clip remover, detach the 3 clips and remove the fender main seal.


Hide 53882H 5.REMOVE FRONT FENDER MAIN SEAL RH

HINT:

Use the same procedure described for the LH side.


Hide 85292B 6.REMOVE FRONT WIPER ARM HEAD CAP

a.
B407913

Disengage the 3 claws to remove the front wiper arm head cap.

HINT:

Use the same procedure for the RH side and LH side.



Hide 85221B 7.REMOVE FRONT WIPER ARM LH

a.

Remove the nut, wiper arm and blade.


Hide 85211B 8.REMOVE FRONT WIPER ARM RH

a.

Remove the nut, wiper arm and blade.


Hide 53383 9.REMOVE HOOD TO COWL TOP SEAL

a.
E156189

Using a clip remover, detach the 12 clips, 4 clamps and remove the hood to cowl top seal.


Hide 55781E 10.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

a.

w/ PTC Heater:

i.

Disconnect the connector.



b.
E156188

Remove the washer hose.


c.
E156191

Remove the 2 clips.


d.

Detach the 17 claws and remove the cowl top ventilator louver sub-assembly.


Hide 85160 11.REMOVE WINDSHIELD WIPER LINK ASSEMBLY

a.
E156190E05
1.25,0.021 1.698,0.229 0.448,0.208 10 true Slide

Disconnect the connector. Then detach the clamp and remove the wire harness from the cowl top panel.


b.

Remove the 3 bolts and slide the link to disconnect the connection as shown in the illustration to remove the wiper link.


Hide 85110 12.REMOVE WINDSHIELD WIPER MOTOR ASSEMBLY

a.
E161961E01
0.056,1.631 1.332,1.836 1.277,0.205 10 Wiper Motor Cover 0.732,1.553 0.732,1.393 0.732,1.393 1.029,1.079 false

Detach the clamp and remove the wiper motor cover.


b.
E156193

Using a screwdriver with the tip wrapped with protective tape, disconnect the rod of the windshield wiper link assembly from the crank arm pivot of the windshield wiper motor assembly as shown in the illustration.

HINT:

Tape the screwdriver tip before use.



c.
E156192

Using a pair of water pump pliers, pull back the boot, taking care not to damage it, and remove the wiper arm from the crank arm pivot as shown in the illustration.

NOTICE:

Do not damage the pivot.



d.
E156196

Using a T30 "TORX" socket, remove the 2 screws and wiper motor.