Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT ASSEMBLY(for HID Headlight) › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052855 LIGHTING (EXT) _0255792 HEADLIGHT ASSEMBLY(for HID Headlight) N

LIGHTING (EXT)  HEADLIGHT ASSEMBLY(for HID Headlight)  ADJUSTMENT  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

It is possible that a bulb is incorrectly installed, affecting headlight aim. Bulb installation should be considered prior to performing the adjustment procedure.



PROCEDURE

Hide 1. VEHICLE PREPARATION FOR HEADLIGHT AIMING ADJUSTMENT

a.

Prepare the vehicle:

HINT:
·

Make sure that there is no damage to the body around the headlights.

·

Fill the fuel tank.

·

Make sure that the oil is filled to the specified level.

·

Make sure that the coolant is filled to the specified level.

·

Inflate the tires to the appropriate pressure.

·

Unload the trunk and vehicle, ensuring that the spare tire, tools and jack are in their original positions.

·

Have a person of average weight (75 kg, 165 lb) sit in the driver seat.

·

Vehicles with height adjustable suspension should have the vehicle height set to the lowest setting prior to adjusting the headlight aim (w/ Active Height Control).




Hide 2. PREPARATION FOR HEADLIGHT AIMING (Using a screen)

U166352E01
1.046,1.693 1.202,1.875 0.156,0.181 10 *b 0.985,1.102 1.141,1.283 0.156,0.181 10 *a

a.

except China:

Prepare the vehicle.

Text in Illustration
*a 90°
*b 25 m or 3 m

·

Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the headlights can be observed and above which it cannot.

·

Place the vehicle at a 90° angle to the wall.

·

Create a 25 m (82 ft.) distance between the vehicle (headlight bulb center) and the wall.

·

Make sure that the vehicle is on a level surface.

·

Bounce the vehicle up and down to settle the suspension.

NOTICE:

A distance of 25 m (82 ft.) between the vehicle (headlight bulb center) and the wall is necessary for proper aim adjustment. If unavailable, secure a distance of exactly 3 m (9.84 ft.) for the check and adjustment. (The target zone will change with the distance, so follow the instructions in the illustration).




b.
U166352E01
1.046,1.693 1.202,1.875 0.156,0.181 10 *b 0.985,1.102 1.141,1.283 0.156,0.181 10 *a

for China:

Prepare the vehicle.

Text in Illustration
*a 90°
*b 10 m or 3 m

·

Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the headlights can be observed and above which it cannot.

·

Place the vehicle at a 90° angle to the wall.

·

Create a 10 m (32.8 ft) distance between the vehicle (fog light bulb center) and the wall.

·

Make sure that the vehicle is on a level surface.

·

Bounce the vehicle up and down to settle the suspension.

NOTICE:

A distance of 10 m (32.8 ft.) between the vehicle (headlight bulb center) and the wall is necessary for proper aim adjustment. If unavailable, secure a distance of exactly 3 m (9.84 ft.) for the check and adjustment. (The target zone will change with the distance, so follow the instructions in the illustration).




c.

Prepare a piece of thick white paper approximately 2 m (6.56 ft.) (height) x 4 m (13.1 ft.) (width) to use as a screen.


d.

Draw a vertical line down the center of the screen (V line).


e.

except China:

Set the screen as shown in the illustration.

HINT:
·

Stand the screen perpendicular to the ground.

·

Align the V line on the screen with the center of the vehicle.

E248184E08
1.333,1.781 3.469,2.188 2.135,0.406 12 false Aligning distance is 25 m: 1.563,0.51 2.292,0.802 0.729,0.292 10 false V RH Line 1.573,1.552 2.344,1.781 0.771,0.229 10 false V LH Line 1.448,0.917 1.719,1.125 0.271,0.208 10 false 90° 6.177,1.073 6.646,1.313 0.469,0.24 10 true V Line 3.083,1.063 3.552,1.302 0.469,0.24 10 true V Line 0.531,2.781 0.99,3.042 0.458,0.26 10 false H Line 1.427,2.948 1.74,3.177 0.313,0.229 10 false 90° 1.688,3.396 2.125,3.646 0.438,0.25 10 false 25 m 4.844,1.792 6.875,2.188 2.031,0.396 12 false Aligning distance is 3 m: 4.844,0.521 5.583,0.813 0.74,0.292 10 false V RH Line 4.854,1.531 5.583,1.792 0.729,0.26 10 false V LH Line 4.958,0.927 5.271,1.156 0.313,0.229 10 false 90° 4.052,2.781 4.521,3.042 0.469,0.26 10 false H Line 4.938,2.948 5.25,3.167 0.313,0.219 10 false 90° 5.073,3.396 5.344,3.667 0.271,0.271 10 false 3 m




f.

for China:

Set the screen as shown in the illustration.

HINT:
·

Stand the screen perpendicular to the ground.

·

Align the V line on the screen with the center of the vehicle.

E248184E10
1.333,1.781 3.469,2.188 2.135,0.406 12 false Aligning distance is 10 m: 1.563,0.563 2.292,0.854 0.729,0.292 10 false V RH Line 1.573,1.49 2.281,1.813 0.708,0.323 10 false V LH Line 1.448,0.917 1.76,1.094 0.313,0.177 10 false 90° 6.177,1.063 6.646,1.302 0.469,0.24 10 true V Line 3.083,1.063 3.552,1.302 0.469,0.24 10 true V Line 0.531,2.781 0.99,3.042 0.458,0.26 10 false H Line 1.427,2.969 1.74,3.198 0.313,0.229 10 false 90° 1.688,3.396 2.125,3.646 0.438,0.25 10 false 10 m 4.844,1.792 6.875,2.188 2.031,0.396 12 false Aligning distance is 3 m: 4.844,0.552 5.583,0.844 0.74,0.292 10 false V RH Line 4.854,1.49 5.542,1.813 0.688,0.323 10 false V LH Line 4.958,0.917 5.271,1.146 0.313,0.229 10 false 90° 4.052,2.771 4.521,3.031 0.469,0.26 10 false H Line 4.958,2.969 5.271,3.188 0.313,0.219 10 false 90° 5.073,3.396 5.344,3.667 0.271,0.271 10 false 3 m




g.
E257183E01
1.17,0.275 1.331,0.419 0.161,0.143 10 *a 1.823,0.275 1.984,0.419 0.161,0.143 10 *b 2.446,0.275 2.607,0.419 0.161,0.143 10 *c 2.936,0.851 3.097,0.994 0.161,0.143 10 *d 0.547,1.698 0.708,1.841 0.161,0.143 10 *e

Draw base lines (H, V LH, and V RH lines) on the screen as shown in the illustration.

Text in Illustration
*a V LH Line
*b V Line
*c V RH Line
*d H Line
*e Ground

HINT:
·

The base lines differ for "low beam inspection" and "high beam inspection".

·

Mark the headlight bulb center marks on the screen. If the center mark cannot be observed on the headlight, use the center of the headlight bulb or the name of the manufacturer marked on the headlight as the center mark.



i.

H Line (Headlight height):

Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the headlight bulb center marks of the low beam headlights.


ii.

V LH Line, V RH Line (Center mark position of the left-hand (LH) and right-hand (RH) headlights):

Draw 2 vertical lines so that they intersect the H line at each center mark (aligned with the center of the low beam headlight bulbs).



Hide 3.INSPECT HEADLIGHT AIMING

a.

Cover the headlight on the opposite side to prevent light from the headlight that is not being inspected from affecting the headlight aiming inspection.

CAUTION:

Do not disconnect the HID high voltage connector for the bulb when performing this aiming inspection.


NOTICE:

Do not keep the headlight covered for more than 3 minutes. The headlight lens is made of synthetic resin, which may melt or be damaged due to excessive heat.


HINT:

When checking the aim of the high beam headlight, cover the low beam headlight.



b.

Start the engine.


c.

except China:

Turn on the headlight and check if the cutoff line matches the preferred cutoff line in the following illustration.

HINT:
·

Since the low beam light and the high beam light on each side have separate reflectors, it is necessary to check and adjust the aim separately for both.

·

The illustration is for LHD vehicles. RHD vehicles are the opposite of the illustration.

·

If the alignment distance is 25 m (82 ft.):

The low beam cutoff line should be within 83 mm (3.27 in.) and 375 mm (1.47 in.) below the H line as well as 249 mm (9.80 in.) left or right of the V LH or V RH line.

·

If the alignment distance is 3 m (9.84 ft.):

The low beam cutoff line should be within 10 mm (0.394 in.) and 45 mm (1.77 in.) below the H line as well as 30 mm (1.18 in.) left or right of the V LH or V RH line.

·

If the alignment distance is 25 m (82 ft.):

The horizontal line of the preferred low beam cutoff line is 249 mm (9.80 in.) below the H line and point A of the preferred low beam cutoff line is on the V LH or V RH line.

·

If the alignment distance is 3 m (9.84 ft.):

The horizontal line of the preferred low beam cutoff line is 30 mm (1.18 in.) below the H line and point A of the preferred low beam cutoff line is on the V LH or V RH line.

E231280E16
1.771,1.438 2.146,0.604 2.146,0.604 2.281,0.604 true 0.646,1.865 1.063,1.448 false 5.219,1.427 5.594,0.594 5.594,0.594 5.729,0.594 true 4.01,1.854 4.427,1.438 false 1.135,0.875 1.76,1.104 0.625,0.229 10 false 83 mm 0.833,0.083 3.031,0.344 2.198,0.26 12 false Aligning distance is 25 m: 4.344,0.094 6.302,0.313 1.958,0.219 12 false Aligning distance is 3 m: 2.333,0.51 2.896,0.698 0.563,0.188 10 false Point A 0.167,1.063 0.677,1.281 0.51,0.219 10 false H Line 0.135,1.521 0.76,1.781 0.625,0.26 10 false 249 mm 0.26,1.833 1.021,2.219 0.76,0.385 10 false Preferred Cutoff Line 1.219,1.802 1.813,2.052 0.594,0.25 10 false 249 mm 1.823,1.802 2.5,2.042 0.677,0.24 10 false 249 mm 1.094,2.271 2.75,2.542 1.656,0.271 10 false V LH Line or V RH Line 2.927,1.302 3.594,1.521 0.667,0.219 10 false 375 mm 5.76,0.521 6.49,0.75 0.729,0.229 10 false Point A 3.604,1.042 4.198,1.271 0.594,0.229 10 false H Line 3.604,1.427 4.146,1.646 0.542,0.219 10 false 30 mm 3.677,1.854 4.458,2.26 0.781,0.406 10 false Preferred Cutoff Line 4.729,1.771 5.26,2.021 0.531,0.25 10 false 30 mm 5.26,1.781 5.781,2.021 0.521,0.24 10 false 30 mm 6.365,1.26 6.927,1.479 0.563,0.219 10 false 45 mm 4.573,0.833 5.188,1.073 0.615,0.24 10 false 10 mm 4.552,2.323 6.208,2.594 1.656,0.271 10 false V LH Line or V RH Line




d.

for China:

Turn on the headlight and check if the cutoff line matches the preferred cutoff line in the following illustration.

HINT:
·

Since the low beam light and the high beam light on each side have separate reflectors, it is necessary to check and adjust the aim separately for both.

·

If the alignment distance is 10 m (32.8 ft.):

The low beam cutoff line should be within 147 mm (5.79 in.) and 241 mm (9.49 in.) below the H line as well as 99 mm (3.89 in.) left or right of the V LH or V RH line.

·

If the alignment distance is 3 m (9.84 ft.):

The low beam cutoff line should be within 44 mm (1.73 in.) and 72 mm (2.83 in.) below the H line as well as 30 mm (1.18 in.) left or right of the V LH or V RH line.

·

If the alignment distance is 10 m (32.8 ft.):

The horizontal line of the preferred low beam cutoff line is 189 mm (7.44 in.) below the H line and point A of the preferred low beam cutoff line is on the V LH or V RH line.

·

If the alignment distance is 3 m (9.84 ft.):

The horizontal line of the preferred low beam cutoff line is 57 mm (2.24 in.) below the H line and point A of the preferred low beam cutoff line is on the V LH or V RH line.

E231280E05
4.104,1.896 4.531,1.448 false 0.781,1.927 1.083,1.458 false 5.24,1.427 5.76,0.594 5.76,0.594 6.01,0.594 true 1.771,1.438 2.292,0.604 2.292,0.604 2.542,0.604 true 0.865,0.094 2.917,0.396 2.052,0.302 12 false Aligning distance is 10 m: 4.323,0.094 6.375,0.396 2.052,0.302 12 false Aligning distance is 3 m: 4.542,2.271 6.083,2.594 1.542,0.323 10 false V LH Line or V RH Line 1.125,2.271 2.667,2.594 1.542,0.323 10 false V LH Line or V RH Line 3.438,1.927 4.792,2.104 1.354,0.177 10 false Preferred Cutoff Line 0.135,1.958 1.448,2.177 1.313,0.219 10 false Preferred Cutoff Line 3.625,1.063 4.135,1.333 0.51,0.271 10 false H Line 0.177,1.073 0.688,1.344 0.51,0.271 10 false H Line 6.052,0.521 6.667,0.833 0.615,0.313 10 false Point A 2.583,0.521 3.198,0.833 0.615,0.313 10 false Point A 0.125,1.51 0.729,1.792 0.604,0.281 10 false 201 mm 1.281,1.792 1.771,2.094 0.49,0.302 10 false 99 mm 1.833,1.792 2.323,2.094 0.49,0.302 10 false 99 mm 1.177,0.938 1.813,1.24 0.635,0.302 10 false 100 mm 2.938,1.313 3.615,1.563 0.677,0.25 10 false 301 mm 5.281,1.792 5.771,2.094 0.49,0.302 10 false 30 mm 4.719,1.792 5.208,2.094 0.49,0.302 10 false 30 mm 6.396,1.281 6.885,1.583 0.49,0.302 10 false 90 mm 3.604,1.51 4.094,1.813 0.49,0.302 10 false 60 mm 4.635,0.917 5.156,1.219 0.521,0.302 10 false 30 mm




e.

except China:

Turn on the high beams and check if the center of intensity for each high beam matches the center of intensity in the illustration.

HINT:
·

Since the low beam light and the high beam light on each side have separate reflectors, it is necessary to check and adjust the aim separately for both.

·

If the alignment distance is 25 m (82.0 ft.):

The high beam center of intensity should be within 175 mm (6.88 in.) above and 249 mm (9.80 in.) below the H line as well as 497 mm (1.63 ft.) left or right of the V LH or V RH line.

·

If the alignment distance is 3 m (9.84 ft.):

The high beam center of intensity should be within 21 mm (0.827 in.) above and 30 mm (1.18 in.) below the H line as well as 60 mm (2.36 in.) left or right of the V LH or V RH line.

E261529E01
5.052,1.354 5.51,0.615 5.51,0.615 5.729,0.615 true 1.656,1.354 2.115,0.615 2.115,0.615 2.333,0.615 true 0.75,0.115 2.906,0.448 2.156,0.333 12 Alignment distance is 25 m: 4.135,0.104 6.292,0.438 2.156,0.333 12 Alignment distance is 3 m: 4.365,2.375 5.854,2.688 1.49,0.313 10 V LH Line or V RH Line 0.969,2.385 2.458,2.698 1.49,0.313 10 V LH Line or V RH Line 5.76,0.531 7.052,0.927 1.292,0.396 10 Center of Intensity 2.375,0.531 3.667,0.927 1.292,0.396 10 Center of Intensity 3.573,1.271 4.052,1.615 0.479,0.344 10 H Line 0.188,1.281 0.667,1.625 0.479,0.344 10 H Line 1.75,2.01 2.344,2.271 0.594,0.26 10 497 mm 1.031,2.01 1.625,2.271 0.594,0.26 10 497 mm 2.802,1.813 3.396,2.073 0.594,0.26 10 249 mm 2.792,0.917 3.385,1.177 0.594,0.26 10 175 mm 4.448,2 5.042,2.26 0.594,0.26 10 60 mm 5.177,1.99 5.771,2.25 0.594,0.26 10 60 mm 6.177,1.823 6.771,2.083 0.594,0.26 10 30 mm 6.177,0.917 6.771,1.177 0.594,0.26 10 21 mm




f.

for China:

Turn on the high beams and check if the center of intensity for each high beam matches the center of intensity in the illustration.

HINT:
·

Since the low beam light and the high beam light on each side have separate reflectors, it is necessary to check and adjust the aim separately for both.

·

If the alignment distance is 10 m (32.8 ft.):

The high beam center of intensity should be within 47 mm (1.85 in.) below the H line.

·

If the alignment distance is 3 m (9.84 ft.):

The high beam center of intensity should be within 14 mm (0.55 in.) below the H line.

·

If the alignment distance is 10 m (32.8 ft.):

The high beam center of intensity for the headlight assembly LH should be within 169 mm (6.65 in.) left and 349 mm (1.14 ft.) right of the V LH line.

·

If the alignment distance is 3 m (9.84 ft.):

The high beam center of intensity for the headlight assembly LH should be within 51 mm (2.0 in.) left and 105 mm (4.13 in.) right of the V LH line.

·

If the alignment distance is 10 m (32.8 ft.):

The high beam center of intensity for the headlight assembly RH should be within 349 mm (1.14 ft.) left or right of the V RH line.

·

If the alignment distance is 3 m (9.84 ft.):

The high beam center of intensity for the headlight assembly RH should be within 105 mm (4.13 in.) left or right of the V RH line.

E261530E05
4.896,1.438 3.677,0.615 true 3.667,0.604 4.458,0.604 false 1.563,1.448 0.365,0.625 true 0.365,0.625 1.125,0.625 false 5,3.615 3.74,2.781 true 3.729,2.781 4.563,2.781 false 1.667,3.615 0.438,2.781 true 0.448,2.781 1.25,2.781 false 4.156,0.063 6.156,0.438 2,0.375 12 false Aligning distance is 3 m: 0.938,0.063 2.938,0.438 2,0.375 12 false Aligning distance is 10 m: 4.49,0.51 5.74,0.823 1.25,0.313 10 false Center of Intensity 1.156,0.531 2.406,0.844 1.25,0.313 10 false Center of Intensity 4.594,2.688 5.844,3 1.25,0.313 10 false Center of Intensity 1.281,2.698 2.531,3.01 1.25,0.313 10 false Center of Intensity 1.313,2.26 2.052,2.583 0.74,0.323 10 false V LH Line 4.656,2.24 5.396,2.563 0.74,0.323 10 false V LH Line 1.417,4.365 2.146,4.74 0.729,0.375 10 false V RH Line 4.76,4.375 5.49,4.75 0.729,0.375 10 false V RH Line 0.26,1.208 0.74,1.573 0.479,0.365 10 false H Line 0.26,3.396 0.74,3.76 0.479,0.365 10 false H Line 3.594,3.385 4.073,3.75 0.479,0.365 10 false H Line 3.594,0.979 4.073,1.344 0.479,0.365 10 false H Line 0.906,1.802 1.51,2.063 0.604,0.26 10 false 169 mm 1.906,1.792 2.521,2.042 0.615,0.25 10 false 349 mm 2.865,1.688 3.385,1.958 0.521,0.271 10 false 94 mm 2.292,0.906 2.802,1.24 0.51,0.333 10 false 47 mm 5.604,0.917 6.188,1.26 0.583,0.344 10 false 14 mm 4.281,1.802 4.813,2.083 0.531,0.281 10 false 51 mm 5.229,1.802 5.844,2.156 0.615,0.354 10 false 105 mm 6.208,1.656 6.781,1.99 0.573,0.333 10 false 28 mm 6.167,3.896 6.75,4.125 0.583,0.229 10 false 28 mm 5.573,3.104 6.156,3.365 0.583,0.26 10 false 14 mm 4.333,3.969 4.948,4.333 0.615,0.365 10 false 105 mm 5.24,3.958 5.854,4.188 0.615,0.229 10 false 105 mm 0.917,3.969 1.531,4.219 0.615,0.25 10 false 349 mm 1.906,3.979 2.521,4.229 0.615,0.25 10 false 349 mm 2.844,3.844 3.396,4.156 0.552,0.313 10 false 94 mm 2.281,3.094 2.792,3.427 0.51,0.333 10 false 47 mm 1.604,0.958 2.115,1.292 0.51,0.333 10 false 99 mm 1.135,0.948 1.646,1.281 0.51,0.333 10 false 99 mm 1.74,3.125 2.25,3.458 0.51,0.333 10 false 99 mm 1.25,3.135 1.76,3.469 0.51,0.333 10 false 99 mm 5.01,0.958 5.594,1.302 0.583,0.344 10 false 30 mm 4.479,0.969 5.063,1.313 0.583,0.344 10 false 30 mm 5.073,3.125 5.635,3.396 0.563,0.271 10 false 30 mm 4.563,3.125 5.063,3.365 0.5,0.24 10 false 30 mm




Hide 4.ADJUSTMENT HEADLIGHT AIMING

a.

Headlight low beam.

i.

Using a screwdriver, adjust the aim.

E251168E03
0.824,0.28 1.017,0.494 0.193,0.214 12 *A 4.02,0.21 4.213,0.424 0.193,0.214 12 *B 1.984,3.072 2.199,3.253 0.215,0.181 10 *1 0.445,3.055 0.678,3.236 0.232,0.181 10 *2 0.681,0.989 0.906,1.171 0.225,0.181 10 *3 2.989,2.003 3.200,2.184 0.211,0.181 10 *3 5.103,3.052 5.311,3.234 0.208,0.181 10 *1 3.851,3.045 4.141,3.226 0.290,0.181 10 *2 3.766,0.812 3.995,0.993 0.229,0.181 10 *3 6.239,1.996 6.461,2.178 0.222,0.181 10 *3 1.81,1.872 2.971,2.063 false 1.238,1.927 0.796,1.141 false 1.127,2.054 0.569,3.05 false 1.766,2.056 2.042,3.075 false 3.974,3.045 4.32,2.041 false 4.959,2.042 5.163,3.051 false 5.014,1.84 6.221,2.063 false 4.433,1.927 3.892,0.953 false

Text in Illustration
*A Type 1 *B Type 2
*1 Vertical Aiming Screw *2 Horizontal Aiming Screw
*3 Screwdriver - -

Adjust the aim of each headlight so that it is within the specified range by turning each aiming screw with a screwdriver.

NOTICE:

The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it and then retighten it, so that the final turn of the screw is in the clockwise direction.


HINT:
·

Since the low beam light and the high beam light on each side have separate reflectors, it is necessary to check and adjust the aim separately for both.

·

When adjusting the horizontal axis of the headlight, the vertical axis will also change. It is necessary to adjust the horizontal position first, and then correct the vertical position.

·

If it is not possible to correctly adjust headlight aim, check the bulb, headlight unit and headlight unit reflector installation.

·

The headlight aim moves up when turning the vertical aiming screw clockwise, and moves down when turning the vertical aiming screw counterclockwise. The headlight aim moves right when turning the horizontal aiming screw clockwise, and moves left when turning the horizontal aiming screw counterclockwise.

·

Confirm the direction of rotation of the aiming screw by observing it while it is being adjusted. Due to the position of the screwdriver, the direction of rotation of the adjusting screw can be different than the direction of rotation of the screwdriver being used to adjust it.





b.

Headlight high beam.

i.

Using a screwdriver, adjust the aim.

E251167E03
0.824,0.28 1.107,0.494 0.284,0.214 12 *A 4.03,0.252 4.300,0.466 0.270,0.214 12 *B 1.439,3.166 1.671,3.348 0.232,0.181 10 *1 2.453,3.136 2.658,3.317 0.205,0.181 10 *2 0.787,1.042 0.999,1.223 0.211,0.181 10 *3 3.123,2.027 3.346,2.208 0.223,0.181 10 *3 4.721,3.108 4.932,3.290 0.211,0.181 10 *1 5.679,3.113 5.904,3.294 0.225,0.181 10 *2 3.831,0.921 4.032,1.102 0.201,0.181 10 *3 6.344,1.956 6.588,2.137 0.244,0.181 10 *3 1.922,2.002 1.545,3.149 false 2.487,2.347 2.529,3.131 false 2.5,2.188 3.114,2.104 false 1.911,1.834 0.946,1.156 false 5.1,1.765 3.976,1.037 false 5.115,1.989 4.833,3.101 false 5.679,2.334 5.739,3.106 false 5.693,2.168 6.343,2.047 false

Text in Illustration
*A Type 1 *B Type 2
*1 Vertical Aiming Screw *2 Horizontal Aiming Screw
*3 Screwdriver - -

Adjust the aim of each headlight so that it is within the specified range by turning each aiming screw with a screwdriver.

NOTICE:

The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it and then retighten it, so that the final turn of the screw is in the clockwise direction.


HINT:
·

Since the low beam light and the high beam light on each side have separate reflectors, it is necessary to check and adjust the aim separately for both.

·

When adjusting the horizontal axis of the headlight, the vertical axis will also change. It is necessary to adjust the horizontal position first, and then correct the vertical position.

·

If it is not possible to correctly adjust headlight aim, check the bulb, headlight unit and headlight unit reflector installation.

·

The headlight aim moves up when turning the vertical aiming screw clockwise, and moves down when turning the vertical aiming screw counterclockwise. The headlight aim moves right when turning the horizontal aiming screw clockwise, and moves left when turning the horizontal aiming screw counterclockwise.

·

Confirm the direction of rotation of the aiming screw by observing it while it is being adjusted. Due to the position of the screwdriver, the direction of rotation of the adjusting screw can be different than the direction of rotation of the screwdriver being used to adjust it.