Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT ASSEMBLY (for Halogen Headlight) › from 2015.08
RM2660E _59 Vehicle Exterior _052855 LIGHTING (EXT) _0255799 HEADLIGHT ASSEMBLY(for Halogen Headlight) A

LIGHTING (EXT)  HEADLIGHT ASSEMBLY(for Halogen Headlight)  DISASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

Handle components indoors as much as possible to prevent foreign matter from entering and adhering to headlight assembly components.

·

Do not reuse parts which have reduced fastening ability due to thread damage.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

When installing components, make sure that the wire harness is not pinched or pulled.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 81194A 1.REMOVE HEADLIGHT PROTECTOR LH

a.
B560769

Remove the headlight protector LH.

NOTICE:

Do not reuse the headlight protector LH.



Hide 81510C 2.REMOVE FRONT TURN SIGNAL LIGHT BULB

a.
E333248E01
2.332,1.994 2.564,2.164 0.232,0.170 10 *a 2.085,1.144 2.395,1.972 false 2.147,3.3 2.956,2.943 false 2.985,2.834 3.217,3.004 0.232,0.170 10 *b

Turn the front turn signal light socket counterclockwise until the matchmark is aligned with the unlock position mark to disconnect the front turn signal light socket.

Text in Illustration
*a Matchmark
*b Unlock Position Mark


b.
E333250

Remove the front turn signal light bulb from the front turn signal light socket.


Hide 81515B 3.REMOVE FRONT TURN SIGNAL LIGHT SOCKET

a.
E333251

Disconnect the connector and remove the front turn signal light socket.


Hide 81610F 4.REMOVE CLEARANCE LIGHT BULB

a.
E334284E01
2.602,1.069 2.810,1.253 0.208,0.184 10 *a 1.85,1.34 2.56,1.179 false 2.917,3.601 3.125,3.785 0.208,0.184 10 *b 2.182,3.875 2.892,3.715 false

Turn the bulb socket counterclockwise until the matchmark is aligned with the unlock position mark to disconnect the bulb socket.

Text in Illustration
*a Matchmark
*b Unlock Position Mark


b.
E334283

Remove the clearance light bulb from the bulb socket.


Hide 81110B 5.REMOVE NO. 1 HEADLIGHT BULB

a.
E334280

Disconnect the connector.


b.
E334281

Turn the No. 1 headlight bulb counterclockwise until the bulb stops.


c.

Pull out the No. 1 headlight bulb and remove it.

NOTICE:

Do not touch the glass part of the No. 1 headlight bulb.



Hide 81110D 6.REMOVE NO. 2 HEADLIGHT BULB

a.
E334277

Disconnect the connector.


b.
E334278

Turn the No. 2 headlight bulb counterclockwise until the bulb stops.


c.

Pull out the No. 2 headlight bulb and remove it.

NOTICE:

Do not touch the glass part of the No. 2 headlight bulb.



Hide 81125 7.REMOVE HEADLIGHT CORD

a.
E334286

Detach the 2 claws and disconnect the 2 connectors.


b.

Detach the wire harness clamp and remove the headlight cord.


Hide 52134J 8.REMOVE FRONT BUMPER BAR REINFORCEMENT LH

a.
E333245

Remove the 2 screws.


b.
E333246

Detach the 2 guides and remove the front bumper reinforcement LH.


Hide 81171B 9.REMOVE HEADLIGHT LENS LH

NOTICE:
·

Perform work using clean rubber gloves.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.



a.
E334288

Remove the 2 screws and inner bracket.


b.
E334287

Remove the 2 screws and outer bracket.


c.

Remove the 7 screws.

B560785E01
1.609,0.061 1.882,0.268 0.273,0.207 12 *A 5.565,0.061 5.838,0.268 0.273,0.207 12 *B

Text in Illustration
*A Headlight Assembly LH Backside *B Headlight Assembly LH Surface


d.

Remove the headlight lens LH:

NOTICE:
·

Perform work using clean rubber gloves.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.



HINT:
·

The connection between the headlight lens LH and headlight housing is extremely tight. Therefore, make sure to use the following method of using a dryer to warm and soften the headlight lens gasket to separate the headlight lens LH and headlight housing.

·

With the headlight lens LH slightly lifted, cut the headlight lens gasket and separate the headlight lens LH.



i.

Using a dryer, warm the headlight lens gasket from the backside of the headlight assembly LH at the separation starting point of the headlight lens LH and headlight housing.

NOTICE:

If the headlight assembly LH is heated unevenly, it will deform or melt.


HINT:
·

If the headlight lens LH cannot be lifted, even after heating, using a screwdriver, lift the headlight lens LH.

·

Tape the screwdriver tip before use.



B560786E01
0.963,1.598 1.602,2.167 0.639,0.569 0.963,1.598 1.602,2.167 0.639,0.569 0.975,1.606 1.195,1.786 0.220,0.180 10 *a 1.413,0.237 1.673,0.427 0.260,0.191 12 *A 3.888,0.237 4.148,0.427 0.260,0.191 12 *B

Text in Illustration
*A Headlight Assembly LH Surface *B Headlight Assembly LH Backside
*a Separation Starting Point - -


ii.

Detach the 2 claws A and slightly lift the headlight lens LH.


iii.

Heat the headlight lens gasket starting from the backside of the headlight assembly LH and finishing at the area around claw B.


iv.

Detach the claw B and slightly lift the headlight lens LH.


v.

Heat the headlight lens gasket starting from the backside of the headlight assembly LH and finishing at the area around claw C.


vi.

Detach the 2 claws C and slightly lift the headlight lens LH.


vii.

Heat the headlight lens gasket starting from the backside of the headlight assembly LH and finishing at the area around claw D.


viii.

Detach the 2 claws D and remove the headlight lens LH.

B560787E01
1.063,1.417 1.25,1.583 0.188,0.167 10 true *a 2.385,2.99 2.573,3.156 0.188,0.167 10 true *a 4.354,3.469 4.542,3.635 0.188,0.167 10 true *c 2.552,0.271 2.74,0.438 0.188,0.167 10 true *b 4.25,0.188 4.438,0.354 0.188,0.167 10 true *c 5.885,2.104 6.073,2.271 0.188,0.167 10 true *d 6.26,1.427 6.448,1.594 0.188,0.167 10 true *d

Text in Illustration
*a Claw A *b Claw B
*c Claw C *d Claw D



Hide 81132B 10.REMOVE HEADLIGHT LENS GASKET

NOTICE:
·

Perform work using clean rubber gloves.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

The gasket must not be reused.



a.

Remove the headlight lens gasket from the headlight lens and headlight housing.

HINT:

Using a dryer, heat the headlight lens gasket. While softening the headlight lens gasket, remove it from the headlight lens LH and headlight housing.