Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT ASSEMBLY (for Halogen Headlight) › from 2015.08
RM2660E _59 Vehicle Exterior _052855 LIGHTING (EXT) _0255799 HEADLIGHT ASSEMBLY(for Halogen Headlight) A

LIGHTING (EXT)  HEADLIGHT ASSEMBLY(for Halogen Headlight)  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

Handle components indoors as much as possible to prevent foreign matter from entering and adhering to headlight assembly components.

·

Do not reuse parts which have reduced fastening ability due to thread damage.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

When installing components, make sure that the wire harness is not pinched or pulled.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 81132B 1.INSTALL HEADLIGHT LENS GASKET

a.
E334293

Clean the headlight lens gasket installation groove.

Text in Illustration
V100155

Area to Clean


b.

Prepare 2 screwdrivers, fold a piece of peeling paper over the tip of each screwdriver and fix the pieces of peeling paper in place with tape.

HINT:

Use the peeling paper that is supplied with the headlight lens gasket.



c.
E336879

Using scissors, cut the headlight lens gasket at a 90°.


d.
E334294

Starting from the position shown in the illustration, set the headlight lens gasket into the straight groove counterclockwise until it meets the corner groove.

Text in Illustration
V100143

Starting Point

NOTICE:

Lightly set the gasket in place without pulling.



e.
E334295

Set the headlight lens gasket into the corner groove and using 2 screwdrivers with their tips wrapped with peeling paper, push the gasket into the bottom of the groove.

Text in Illustration
V100136

Corner Groove
V100144

Headlight Lens Gasket
V100155

Peeling Paper

NOTICE:
·

Lightly set the gasket in place without pulling.

·

If the headlight lens gasket is set while pulled, the gasket will be pushed up at the corner groove.




f.

Repeat the following order while working in a circle back to the starting point.

i.

Set headlight lens gasket into straight groove.


ii.

Push into bottom of groove.


iii.

Set into corner groove.


iv.

Push into bottom of groove.



g.
E334296E01
2.277,2.288 2.475,2.449 0.198,0.161 10 *a

Using scissors, cut the headlight lens gasket at a 45°angle at the starting point so that the gasket overlaps itself 20 mm (0.7874 in.) and set the gasket in place.

Text in Illustration
*a 20 mm (0.7874 in.)
V100136

Corner Groove


h.

Check the installation condition of the headlight lens gasket.

OK:

Gasket not pushed up or protruding.

No gap where gasket overlaps.


NOTICE:

Check the corners carefully since the gasket can easily become pushed up in those areas.



Hide 81171B 2.INSTALL HEADLIGHT LENS LH

NOTICE:
·

Perform work using clean rubber gloves.

·

Do not touch the inner surface of the lens with bare hands.

·

If dirty, lightly wipe with a soft cloth.



a.

Clean the headlight lens gasket contact surface.


b.
E317610

Set the headlight lens LH in place.

NOTICE:

Set the headlight lens LH in the middle of the headlight lens gasket as shown in the illustration.


Text in Illustration
V100144

Headlight Lens Gasket
V100146

Head Light Housing
V100155

Headlight Lens LH


c.

Check that the entire circumference of the headlight lens LH is positioned above the middle of the headlight lens gasket.


d.

Attach the claws in the following order to install the headlight lens LH: The 2 claws D, 2 claws C, claw B, and then 2 claws A.

B560787E01
1.063,1.417 1.25,1.583 0.188,0.167 10 true *a 2.385,2.99 2.573,3.156 0.188,0.167 10 true *a 4.354,3.469 4.542,3.635 0.188,0.167 10 true *c 2.552,0.271 2.74,0.438 0.188,0.167 10 true *b 4.25,0.188 4.438,0.354 0.188,0.167 10 true *c 5.885,2.104 6.073,2.271 0.188,0.167 10 true *d 6.26,1.427 6.448,1.594 0.188,0.167 10 true *d

Text in Illustration
*a Claw A *b Claw B
*c Claw C *d Claw D


e.

Install the 7 screws.

B560785E01
1.609,0.061 1.882,0.268 0.273,0.207 12 *A 5.565,0.061 5.838,0.268 0.273,0.207 12 *B

Text in Illustration
*A Headlight Assembly LH Backside *B Headlight Assembly LH Surface


f.

Install the outer bracket with the 2 screws.


g.

Install the inner bracket with the 2 screws.


Hide 52134J 3.INSTALL FRONT BUMPER BAR REINFORCEMENT LH

a.

Attach the 2 guides to install the front bumper bar reinforcement LH.


b.

Install the 2 screws.


Hide 81125 4.INSTALL HEADLIGHT CORD

a.

Attach the wire harness clamp to install the headlight cord.


b.

Attach the 2 claws to connect the 2 connectors.


Hide 81110D 5.INSTALL NO. 2 HEADLIGHT BULB

a.
E334279

Insert and turn the No. 2 headlight bulb clockwise until the bulb stops to install it.

NOTICE:

Do not touch the glass part of the No. 2 headlight bulb.



Hide 81110B 6.INSTALL NO. 1 HEADLIGHT BULB

a.
E334282

Insert and turn the No. 1 headlight bulb clockwise until the bulb stops to install it.

NOTICE:

Do not touch the glass part of the No. 1 headlight bulb.



Hide 81610F 7.INSTALL CLEARANCE LIGHT BULB

a.

Install the clearance light bulb to the bulb socket.


b.
E334285E01
2.686,0.699 2.896,0.887 0.210,0.187 10 *a 2.013,1.317 2.664,0.826 false 2.173,1.424 2.678,1.424 false 2.715,1.318 2.924,1.505 0.210,0.187 10 *b 2.348,4.008 2.558,4.195 0.210,0.187 10 *c 1.867,3.854 2.314,4.089 false

Align the matchmark of the bulb socket with the unlock position mark, and then rotate the bulb socket clockwise until the lock position mark to connect the bulb socket.

Text in Illustration
*a Matchmark
*b Unlock Position Mark
*c Lock Position Mark


Hide 81515B 8.INSTALL FRONT TURN SIGNAL LIGHT SOCKET

a.

Connect the connector to install the front turn signal light socket.


Hide 81510C 9.INSTALL FRONT TURN SIGNAL LIGHT BULB

a.

Install the front turn signal light bulb to the front turn signal light socket.


b.
E333249E01
2.019,0.904 1.596,0.25 false 1.397,0.132 1.584,0.302 0.187,0.170 10 *a 2.144,0.855 2.768,1.322 false 2.792,1.246 2.979,1.416 0.187,0.170 10 *b 2.239,3.606 2.974,3.35 false 3.01,3.237 3.197,3.407 0.187,0.170 10 *c

Align the matchmark of the front turn signal light socket with the unlock position mark, and then rotate the front turn signal light socket clockwise until the lock position mark to connect the front turn signal light socket.

Text in Illustration
*a Matchmark
*b Unlock Position Mark
*c Lock Position Mark


Hide 81194A 10.INSTALL HEADLIGHT PROTECTOR LH

a.
B560772E01
2.323,0.865 2.906,0.865 true 2.938,0.771 3.25,0.927 0.313,0.156 10 true *a

Clean the installation area of the headlight protector LH shown in the illustration.

NOTICE:

Remove any remaining double-sided tape, and then clean the area with non-residue solvent.


Text in Illustration
*a Cleaning Area


b.

Remove approximately 30 mm (1.18 in.) of the release paper from a new headlight protector LH.


c.
B560775E01
0.469,1.385 1.24,1.385 true 0.271,1.292 0.583,1.448 0.313,0.156 10 false *a

Align the exposed end of the headlight protector LH with the line.

Text in Illustration
*a Line


d.
B560778

Gradually remove the release paper and temporarily install the headlight protector LH while keeping it aligned with the curve of the headlight unit assembly.


e.
B560781E01
0.594,1.208 1.594,1.208 true 0.385,1.115 0.698,1.271 0.313,0.156 10 false *a

Press the entire length of the headlight protector LH to install it.

NOTICE:

When pressing, do not slide your finger, as doing so may stretch the part.


Text in Illustration
*a Press Area