84140
1.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY (for LH Side)
w/ Entry and Start System:
Inspect the light control switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E14-18 (T) - E14-15 (EL) | Light control switch OFF | 10 kΩ or higher |
| E14-19 (H) - E14-15 (EL) | ||
| E14-20 (A) - E14-15 (EL) | ||
| E14-20 (A) - E14-15 (EL) | Light control switch AUTO | Below 1 Ω |
| E14-18 (T) - E14-15 (EL) | Light control switch tail | Below 1 Ω |
| E14-18 (T) - E14-15 (EL) | Light control switch head | Below 1 Ω |
| E14-19 (H) - E14-15 (EL) |
If the result is not as specified, replace the headlight dimmer switch assembly.
| *a | Component without harness connected
(Headlight Dimmer Switch Assembly) |
w/o Entry and Start System:
Inspect the light control switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E14-18 (T) - E14-12 (EL) | Light control switch OFF | 10 kΩ or higher |
| E14-19 (A) - E14-12 (EL) | ||
| E14-20 (H) - E14-12 (EL) | ||
| E14-19 (A) - E14-12 (EL) | Light control switch AUTO | Below 1 Ω |
| E14-18 (T) - E14-12 (EL) | Light control switch tail | Below 1 Ω |
| E14-18 (T) - E14-12 (EL) | Light control switch head | Below 1 Ω |
| E14-20 (H) - E14-12 (EL) |
If the result is not as specified, replace the headlight dimmer switch assembly.
| *a | Component without harness connected
(Headlight Dimmer Switch Assembly) |
w/ Entry and Start System:
Inspect the headlight dimmer switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E14-14 (HU) - E14-15 (EL) | Headlight dimmer switch flash | Below 1 Ω |
| E14-17 (HF) - E14-15 (EL) | ||
| E14-14 (HU) - E14-15 (EL) | Headlight dimmer switch high beam | Below 1 Ω |
If the result is not as specified, replace the headlight dimmer switch assembly.
| *a | Component without harness connected
(Headlight Dimmer Switch Assembly) |
w/o Entry and Start System:
Inspect the headlight dimmer switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E14-11 (HU) - E14-12 (EL) | Headlight dimmer switch flash | Below 1 Ω |
| E14-17 (HF) - E14-12 (EL) | ||
| E14-11 (HU) - E14-12 (EL) | Headlight dimmer switch high beam | Below 1 Ω |
If the result is not as specified, replace the headlight dimmer switch assembly.
| *a | Component without harness connected
(Headlight Dimmer Switch Assembly) |
w/ Entry and Start System:
Inspect the turn signal light switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E14-11 (TL) - E14-15 (EL) | Turn signal switch neutral | 10 kΩ or higher |
| E14-12 (TR) - E14-15 (EL) | ||
| E14-13 (CR) - E14-15 (EL) | ||
| E14-11 (TL) - E14-15 (EL) | Turn signal switch left turn
(self cancel condition) |
Below 1 Ω |
| E14-11 (TL) - E14-15 (EL) | Turn signal switch left turn
(cancel ratchet operation condition) |
Below 1 Ω |
| E14-11 (TL) - E14-13 (CR) | ||
| E14-13 (CR) - E14-15 (EL) | ||
| E14-12 (TR) - E14-15 (EL) | Turn signal switch right turn
(self cancel condition) |
Below 1 Ω |
| E14-12 (TR) - E14-15 (EL) | Turn signal switch right turn
(cancel ratchet operation condition) |
Below 1 Ω |
| E14-12 (TR) - E14-13 (CR) | ||
| E14-13 (CR) - E14-15 (EL) |
The self cancel condition indicates when the turn signal switch returns to the neutral position after releasing your hand from the switch (switch is operated within 7°).
The cancel ratchet operation condition indicates the condition when the turn signal switch does not return to the neutral position even after releasing your hand (switch is operated within 12°).
If the result is not as specified, replace the headlight dimmer switch assembly.
| *a | Component without harness connected
(Headlight Dimmer Switch Assembly) |
w/o Entry and Start System:
Inspect the turn signal light switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E14-15 (TL) - E14-12 (EL) | Turn signal switch neutral | 10 kΩ or higher |
| E14-13 (TR) - E14-12 (EL) | ||
| E14-14 (CR) - E14-12 (EL) | ||
| E14-15 (TL) - E14-12 (EL) | Turn signal switch left turn
(self cancel condition) |
Below 1 Ω |
| E14-15 (TL) - E14-12 (EL) | Turn signal switch left turn
(cancel ratchet operation condition) |
Below 1 Ω |
| E14-15 (TL) - E14-14 (CR) | ||
| E14-14 (CR) - E14-12 (EL) | ||
| E14-13 (TR) - E14-12 (EL) | Turn signal switch right turn
(self cancel condition) |
Below 1 Ω |
| E14-13 (TR) - E14-12 (EL) | Turn signal switch right turn
(cancel ratchet operation condition) |
Below 1 Ω |
| E14-13 (TR) - E14-14 (CR) | ||
| E14-14 (CR) - E14-12 (EL) |
The self cancel condition indicates when the turn signal switch returns to the neutral position after releasing your hand from the switch (switch is operated within 7°).
The cancel ratchet operation condition indicates the condition when the turn signal switch does not return to the neutral position even after releasing your hand (switch is operated within 12°).
If the result is not as specified, replace the headlight dimmer switch assembly.
| *a | Component without harness connected
(Headlight Dimmer Switch Assembly) |
w/ Entry and Start System:
Inspect the front fog light switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E14-4 (BFG) - E14-8 (LFG) | Front fog light switch off | 10 kΩ or higher |
| E14-4 (BFG) - E14-8 (LFG) | Front fog light switch on | Below 1 Ω |
If the result is not as specified, replace the headlight dimmer switch assembly.
| *a | Component without harness connected
(Headlight Dimmer Switch Assembly) |
w/o Entry and Start System:
Inspect the front fog light switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E14-4 (BFG) - E14-3 (LFG) | Front fog light switch off | 10 kΩ or higher |
| E14-4 (BFG) - E14-3 (LFG) | Front fog light switch on | Below 1 Ω |
If the result is not as specified, replace the headlight dimmer switch assembly.
| *a | Component without harness connected
(Headlight Dimmer Switch Assembly) |
w/ Entry and Start System:
Inspect the rear fog light switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E14-7 (B) - E14-8 (LFG) | Rear fog light switch off | 10 kΩ or higher |
| E14-7 (B) - E14-8 (LFG) | Rear fog light switch on | Below 1 Ω |
If the result is not as specified, replace the headlight dimmer switch assembly.
| *a | Component without harness connected
(Headlight Dimmer Switch Assembly) |
w/o Entry and Start System:
Inspect the rear fog light switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E14-7 (B) - E14-3 (LFG) | Rear fog light switch off | 10 kΩ or higher |
| E14-7 (B) - E14-3 (LFG) | Rear fog light switch on | Below 1 Ω |
If the result is not as specified, replace the headlight dimmer switch assembly.
| *a | Component without harness connected
(Headlight Dimmer Switch Assembly) |
84140
2.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY (for RH Side)
w/ Entry and Start System:
Inspect the light control switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E14-11 (A) - E14-16 (EL) | Light control switch OFF | 10 kΩ or higher |
| E14-12 (H) - E14-16 (EL) | ||
| E14-13 (T) - E14-16 (EL) | ||
| E14-11 (A) - E14-16 (EL) | Light control switch AUTO | Below 1 Ω |
| E14-13 (T) - E14-16 (EL) | Light control switch tail | Below 1 Ω |
| E14-12 (H) - E14-16 (EL) | Light control switch head | Below 1 Ω |
| E14-13 (T) - E14-16 (EL) |
If the result is not as specified, replace the headlight dimmer switch assembly.
| *a | Component without harness connected
(Headlight Dimmer Switch Assembly) |
w/o Entry and Start System:
Inspect the light control switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E14-11 (H) - E14-19 (EL) | Light control switch OFF | 10 kΩ or higher |
| E14-12 (A) - E14-19 (EL) | ||
| E14-13 (T) - E14-19 (EL) | ||
| E14-12 (A) - E14-19 (EL) | Light control switch AUTO | Below 1 Ω |
| E14-13 (T) - E14-19 (EL) | Light control switch tail | Below 1 Ω |
| E14-11 (H) - E14-19 (EL) | Light control switch head | Below 1 Ω |
| E14-13 (T) - E14-19 (EL) |
If the result is not as specified, replace the headlight dimmer switch assembly.
| *a | Component without harness connected
(Headlight Dimmer Switch Assembly) |
w/ Entry and Start System:
Inspect the headlight dimmer switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E14-17 (HU) - E14-16 (EL) | Headlight dimmer switch flash | Below 1 Ω |
| E14-14 (HF) - E14-16 (EL) | ||
| E14-17 (HU) - E14-16 (EL) | Headlight dimmer switch high beam | Below 1 Ω |
If the result is not as specified, replace the headlight dimmer switch assembly.
| *a | Component without harness connected
(Headlight Dimmer Switch Assembly) |
w/o Entry and Start System:
Inspect the headlight dimmer switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E14-14 (HF) - E14-19 (EL) | Headlight dimmer switch flash | Below 1 Ω |
| E14-20 (HU) - E14-19 (EL) | ||
| E14-20 (HU) - E14-19 (EL) | Headlight dimmer switch high beam | Below 1 Ω |
If the result is not as specified, replace the headlight dimmer switch assembly.
| *a | Component without harness connected
(Headlight Dimmer Switch Assembly) |
w/ Entry and Start System:
Inspect the turn signal light switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E14-19 (TL) - E14-16 (EL) | Turn signal switch neutral | 10 kΩ or higher |
| E14-20 (TR) - E14-16 (EL) | ||
| E14-18 (CR) - E14-16 (EL) | ||
| E14-19 (TL) - E14-16 (EL) | Turn signal switch left turn
(self cancel condition) |
Below 1 Ω |
| E14-19 (TL) - E14-16 (EL) | Turn signal switch left turn
(cancel ratchet operation condition) |
Below 1 Ω |
| E14-19 (TL) - E14-18 (CR) | ||
| E14-18 (CR) - E14-16 (EL) | ||
| E14-20 (TR) - E14-16 (EL) | Turn signal switch right turn
(self cancel condition) |
Below 1 Ω |
| E14-20 (TR) - E14-16 (EL) | Turn signal switch right turn
(cancel ratchet operation condition) |
Below 1 Ω |
| E14-20 (TR) - E14-18 (CR) | ||
| E14-18 (CR) - E14-16 (EL) |
The self cancel condition indicates when the turn signal switch returns to the neutral position after releasing your hand from the switch (switch is operated within 7°).
The cancel ratchet operation condition indicates the condition when the turn signal switch does not return to the neutral position even after releasing your hand (switch is operated within 12°).
If the result is not as specified, replace the headlight dimmer switch assembly.
| *a | Component without harness connected
(Headlight Dimmer Switch Assembly) |
w/o Entry and Start System:
Inspect the turn signal light switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E14-18 (TL) - E14-19 (EL) | Turn signal switch neutral | 10 kΩ or higher |
| E14-16 (TR) - E14-19 (EL) | ||
| E14-17 (CR) - E14-19 (EL) | ||
| E14-18 (TL) - E14-19 (EL) | Turn signal switch left turn
(self cancel condition) |
Below 1 Ω |
| E14-18 (TL) - E14-19 (EL) | Turn signal switch left turn
(cancel ratchet operation condition) |
Below 1 Ω |
| E14-18 (TL) - E14-17 (CR) | ||
| E14-17 (CR) - E14-19 (EL) | ||
| E14-16 (TR) - E14-19 (EL) | Turn signal switch right turn
(self cancel condition) |
Below 1 Ω |
| E14-16 (TR) - E14-19 (EL) | Turn signal switch right turn
(cancel ratchet operation condition) |
Below 1 Ω |
| E14-16 (TR) - E14-17 (CR) | ||
| E14-17 (CR) - E14-19 (EL) |
The self cancel condition indicates when the turn signal switch returns to the neutral position after releasing your hand from the switch (switch is operated within 7°).
The cancel ratchet operation condition indicates the condition when the turn signal switch does not return to the neutral position even after releasing your hand (switch is operated within 12°).
If the result is not as specified, replace the headlight dimmer switch assembly.
| *a | Component without harness connected
(Headlight Dimmer Switch Assembly) |
w/ Entry and Start System:
Inspect the front fog light switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E14-2 (BFG) - E14-3 (LFG) | Front fog light switch off | 10 kΩ or higher |
| E14-2 (BFG) - E14-3 (LFG) | Front fog light switch on | Below 1 Ω |
If the result is not as specified, replace the headlight dimmer switch assembly.
| *a | Component without harness connected
(Headlight Dimmer Switch Assembly) |
w/o Entry and Start System:
Inspect the front fog light switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E14-7 (BFG) - E14-8 (LFG) | Front fog light switch off | 10 kΩ or higher |
| E14-7 (BFG) - E14-8 (LFG) | Front fog light switch on | Below 1 Ω |
If the result is not as specified, replace the headlight dimmer switch assembly.
| *a | Component without harness connected
(Headlight Dimmer Switch Assembly) |
w/ Entry and Start System:
Inspect the rear fog light switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E14-4 (B) - E14-3 (LFG) | Rear fog light switch off | 10 kΩ or higher |
| E14-4 (B) - E14-3 (LFG) | Rear fog light switch on | Below 1 Ω |
If the result is not as specified, replace the headlight dimmer switch assembly.
| *a | Component without harness connected
(Headlight Dimmer Switch Assembly) |
w/o Entry and Start System:
Inspect the rear fog light switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E14-9 (B) - E14-8 (LFG) | Rear fog light switch off | 10 kΩ or higher |
| E14-9 (B) - E14-8 (LFG) | Rear fog light switch on | Below 1 Ω |
If the result is not as specified, replace the headlight dimmer switch assembly.
| *a | Component without harness connected
(Headlight Dimmer Switch Assembly) |