Home › Vehicle Exterior › LIGHTING (EXT) › HAZARD WARNING SWITCH › from 2015.08
RM2660E _59 Vehicle Exterior _052855 LIGHTING (EXT) _0255805 HAZARD WARNING SWITCH G

LIGHTING (EXT)  HAZARD WARNING SWITCH  INSPECTION  


PROCEDURE

Hide 84330 1.INSPECT HAZARD WARNING SIGNAL SWITCH ASSEMBLY (w/o Audio)

a.

Inspect the hazard warning signal switch assembly.

i.
U165918E02
0.167,0 0.427,0.24 0.26,0.24 10 false *a 1.573,0.74 1.979,0.938 0.406,0.198 10 false F130

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
4 - 1 Hazard warning switch off 10 kΩ or higher
Hazard warning switch on Below 1 Ω


If the result is not as specified, replace the hazard warning signal switch assembly.

Text in Illustration
*a Component without harness connected
(Hazard Warning Signal Switch Assembly)



b.

Check the illumination.

i.
U165919E01
0.165,0.042 0.422,0.278 0.257,0.236 10 *a 0.99,1.791 1.344,1.972 0.354,0.180 10 ILL+ 2.202,1.791 2.556,1.972 0.354,0.180 10 ILL- 1.703,1.538 1.368,1.873 false 1.832,1.534 2.167,1.869 false 1.564,0.696 1.971,0.895 0.407,0.199 10 F130

Apply battery voltage to the connector, and check the LED illumination condition.

OK:
Measurement Condition Specified Condition
Battery positive (+) → F130-3 (ILL+)
Battery negative (-) → F130-2 (ILL-)
Illuminates


If the result is not as specified, replace the hazard warning signal switch assembly.

Text in Illustration
*a Component without harness connected
(Hazard Warning Signal Switch Assembly)



Hide 83910 2.INSPECT CLOCK ASSEMBLY (for Radio and Display Type)

a.

Inspect the clock assembly.

i.
U166550E02
1.313,0.573 1.646,0.99 false 1.229,0.99 0.667,0.99 false 0.135,0.063 0.323,0.24 0.188,0.177 10 false *a 1.198,0.427 1.344,0.625 0.146,0.198 10 false F 1.635,0.198 1.865,0.406 0.229,0.208 10 false g2 0.542,0.917 0.688,1.115 0.146,0.198 10 false E

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
g2-5 (F) - g2-8 (E) Hazard warning switch off 10 kΩ or higher
Hazard warning switch on Below 1 Ω


If the result is not as specified, replace the clock assembly.

Text in Illustration
*a Component without harness connected
(Clock Assembly)



b.

Check the illumination.

i.
U166551E02
2.052,1.229 2.052,1.75 false 1.365,0.99 0.854,0.396 false 0.146,0 0.333,0.177 0.188,0.177 10 false *a 1.938,1.781 2.302,1.979 0.365,0.198 10 false ILL+ 1.635,0.188 1.865,0.396 0.229,0.208 10 false g2 0.573,0.281 0.865,0.479 0.292,0.198 10 false ILL-

Apply battery voltage to the connector, and check the LED illumination condition.

OK:
Measurement Condition Specified Condition
Battery positive (+) → g2-10 (ILL+)
Battery negative (-) → g2-7 (ILL-)
Illuminates


If the result is not as specified, replace the clock assembly.

Text in Illustration
*a Component without harness connected
(Clock Assembly)



Hide 86110B 3.INSPECT MULTI-DISPLAY ASSEMBLY (w/ Navigation System)

a.

Inspect the multi-display assembly (hazard warning switch).

i.

Measure the resistance according to the value(s) in the table below.

U166605E02
2.615,1.583 2.615,2.115 false 5.042,1.573 5.042,2.115 false 0.094,0.031 0.302,0.24 0.208,0.208 10 false *a 2.417,2.135 2.885,2.323 0.469,0.188 10 false GND1 4.896,2.135 5.25,2.333 0.354,0.198 10 false HAZ 1.698,0.438 2.031,0.615 0.333,0.177 10 false F79 5.313,0.448 5.646,0.625 0.333,0.177 10 false F97

Text in Illustration
*a Component without harness connected
(Multi-display Assembly)
- -

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F97-12 (HAZ) - F79-13 (GND1) Hazard warning switch off 10 kΩ or higher
Hazard warning switch on Below 1 Ω


If the result is not as specified, replace the multi-display assembly.



b.

Check the illumination.

i.

Apply battery voltage to the connector and check the LED illumination conditions.

U166606E02
3.021,0.635 2.469,1.292 false 5.844,1.552 5.844,2.083 false 0.094,0.031 0.302,0.24 0.208,0.208 10 false *a 3.083,0.531 3.531,0.708 0.448,0.177 9 false ILL 5.75,2.188 6.26,2.385 0.51,0.198 10 false ILL- 1.667,0.354 2,0.531 0.333,0.177 10 false F79 5.281,0.365 5.615,0.542 0.333,0.177 10 false F97

Text in Illustration
*a Component without harness connected
(Multi-display Assembly)
- -

OK:
Measurement Condition Specified Condition
Battery positive (+) → F79-2 (ILL)
Battery negative (-) → F97-7 (ILL-)
Illuminates


If the result is not as specified, replace the multi-display assembly.