Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052855 LIGHTING (EXT) _0255811 LIGHTING SYSTEM U

LIGHTING (EXT)  LIGHTING SYSTEM  TERMINALS OF ECU  


CHECK MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)


U164692E05
2.875,1.094 2.781,1.094 2.781,1.094 2.365,1.354 true 5.51,0.698 5.427,0.698 5.427,0.698 5.01,0.958 true 2.865,1.635 2.792,1.635 2.792,1.635 2.385,1.792 true 2.906,2.635 2.813,2.635 2.813,2.635 2.396,2.385 true 2.885,2.229 2.813,2.229 2.813,2.229 2.406,2.135 true 2.24,2.792 2.469,2.958 0.229,0.167 10 false 2A 1.083,3.635 1.313,3.802 0.229,0.167 10 false 2A 1.958,2.042 2.208,2.24 0.25,0.198 10 false 2B 3.083,3.635 3.292,3.802 0.208,0.167 10 false 2B 1.958,1.177 2.167,1.344 0.208,0.167 10 false 2C 5.635,3.635 5.844,3.802 0.208,0.167 10 false 2C 4.938,1.656 5.146,1.823 0.208,0.167 10 false 2D 1.552,5.177 1.76,5.344 0.208,0.167 10 false 2D 4.406,5.177 4.615,5.344 0.208,0.167 10 false 2E 5.552,0.615 5.76,0.781 0.208,0.167 10 false 2E 2.917,1.021 3.135,1.188 0.219,0.167 10 false E1 6.042,7.01 6.26,7.177 0.219,0.167 10 false E1 2.917,1.542 3.135,1.708 0.219,0.167 10 false E2 3.531,7.01 3.75,7.177 0.219,0.167 10 false E2 2.917,2.146 3.135,2.313 0.219,0.167 10 false E3 1.063,7 1.281,7.167 0.219,0.167 10 false E3 2.948,2.552 3.167,2.719 0.219,0.167 10 false E4 6.094,5.083 6.313,5.25 0.219,0.167 10 false E4

a.

Disconnect the E1, E2, E3, 2A, 2B, 2C, and 2D ECU connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
2A-1 - Body ground B - Body ground Battery power supply Always 11 to 14 V
2D-62 (GND2) - Body ground W-B - Body ground Body ground Always Below 1 Ω
2D-62 (GND1) - Body ground*1 W-B - Body ground Body ground Always Below 1 Ω
E1-24 (DCTY) - Body ground*2 L - Body ground Front door courtesy light switch LH signal Front door LH open Below 1 Ω
E1-24 (DCTY) - Body ground*2 L - Body ground Front door courtesy light switch LH signal Front door LH closed 10 kΩ or higher
E1-24 (DCTY) - Body ground*3 P - Body ground Front door courtesy light switch LH signal Front door LH open Below 1 Ω
E1-24 (DCTY) - Body ground*3 P - Body ground Front door courtesy light switch LH signal Front door LH closed 10 kΩ or higher
E2-21 (PCTY) - Body ground*2 P - Body ground Front door courtesy light switch RH signal Front door RH open Below 1 Ω
E2-21 (PCTY) - Body ground*2 P - Body ground Front door courtesy light switch RH signal Front door RH closed 10 kΩ or higher
E2-21 (PCTY) - Body ground*3 L - Body ground Front door courtesy light switch RH signal Front door RH open Below 1 Ω
E2-21 (PCTY) - Body ground*3 L - Body ground Front door courtesy light switch RH signal Front door RH closed 10 kΩ or higher
2C-2 (LCTY) - Body ground W - Body ground Rear door courtesy light switch LH signal Rear door LH open Below 1 Ω
2C-2 (LCTY) - Body ground W - Body ground Rear door courtesy light switch LH signal Rear door LH closed 10 kΩ or higher
E2-7 (RCTY) - Body ground*1 G - Body ground Rear door courtesy light switch RH signal Rear door RH open Below 1 Ω
E2-7 (RCTY) - Body ground*1 G - Body ground Rear door courtesy light switch RH signal Rear door RH closed 10 kΩ or higher
E1-17 (RCTY) - Body ground*4 G - Body ground Rear door courtesy light switch RH signal Rear door RH open Below 1 Ω
E1-17 (RCTY) - Body ground*4 G - Body ground Rear door courtesy light switch RH signal Rear door RH closed 10 kΩ or higher
E2-25 (BCTY) - Body ground W - Body ground Back door courtesy light switch signal Back door open Below 1 Ω
E2-25 (BCTY) - Body ground W - Body ground Back door courtesy light switch signal Back door closed 10 kΩ or higher
E1-23 (TAIL) - Body ground V - Body ground Light control switch TAIL signal Light control switch tail Below 1 Ω
E1-23 (TAIL) - Body ground V - Body ground Light control switch TAIL signal Light control switch except tail 10 kΩ or higher
E2-17 (HEAD) - Body ground R- Body ground Light control switch HEAD signal Light control switch head Below 1 Ω
E2-17 (HEAD) - Body ground R - Body ground Light control switch HEAD signal Light control switch except head 10 kΩ or higher
E1-21 (A) - Body ground G - Body ground Light control switch AUTO signal Light control switch auto Below 1 Ω
E1-21 (A) - Body ground G - Body ground Light control switch AUTO signal Light control switch except auto 10 kΩ or higher
E2-28 (FFOG) - Body ground*5 R - Body ground Front fog light switch signal Front fog light switch on Below 1 Ω
E2-28 (FFOG) - Body ground*5 R - Body ground Front fog light switch signal Front fog light switch off 10 kΩ or higher
E2-9 (RFOG) - Body ground*6 R - Body ground Rear fog light switch signal Rear fog light switch on Below 1 Ω
E2-9 (RFOG) - Body ground*6 R - Body ground Rear fog light switch signal Rear fog light switch off 10 kΩ or higher
2D-13 (HU) - Body ground R - Body ground Dimmer switch high signal Dimmer switch high Below 1 Ω
2D-13 (HU) - Body ground R - Body ground Dimmer switch high signal Dimmer switch except high or flash 10 kΩ or higher
E1-13 (HF) - Body ground GR - Body ground Dimmer switch flash signal Dimmer switch flash Below 1 Ω
E1-13 (HF) - Body ground GR - Body ground Dimmer switch flash signal Dimmer switch except flash 10 kΩ or higher
2D-51 (ILE) - Body ground G - Body ground Interior light signal Map light on Below 1 Ω
2D-51 (ILE) - Body ground G - Body ground Interior light signal Map light off 10 kΩ or higher

*1: w/o Entry and Start System

*2: for LHD

*3: for RHD

*4: w/ Entry and Start System

*5: w/ Front Fog Light

*6: w/ Rear Fog Light



c.

Reconnect the E1, E2, E3, 2A, 2B, 2C, and 2D ECU connectors.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
E1-4 (FFGO) - Body ground*1 R - Body ground Front fog light signal Light control switch tail,
front fog light switch on
Below 1 V
E1-4 (FFGO) - Body ground*1 R - Body ground Front fog light signal Light control switch tail,
front fog light switch off
11 to 14 V
E2-8 (DRLE) - Body ground*2, *3 R - Body ground Daytime running light signal Daytime running light on Below 1 V
E2-8 (DRLE) - Body ground*2, *3 R - Body ground Daytime running light signal Daytime running light off 11 to 14 V
E3-14 (DRLE) - Body ground*2, *4 R - Body ground Daytime running light signal Daytime running light on Below 1 V
E3-14 (DRLE) - Body ground*2, *4 R - Body ground Daytime running light signal Daytime running light on 11 to 14 V
E2-15 (DIM) - Body ground*5 L - Body ground Headlight high beam signal Light control switch head,
dimmer switch high
Below 1 V
E2-15 (DIM) - Body ground*5 L - Body ground Headlight high beam signal Light control switch head,
dimmer switch except high
11 to 14 V
E3-14 (RFGO) - Body ground*6 R - Body ground Rear fog light signal Light control switch tail,
rear fog light switch off
Below 1 V
E3-14 (RFGO) - Body ground*6 R - Body ground Rear fog light signal Light control switch tail,
rear fog light switch off
11 to 14 V
2B-18 (HRLY) - Body ground L - Body ground Headlight low beam signal Light control switch head,
dimmer switch low
Below 1 V
2B-18 (HRLY) - Body ground L - Body ground Headlight low beam signal Light control switch head,
dimmer switch except low
11 to 14 V
2B-16 (DIM) - Body ground*7 LG - Body ground Headlight high beam signal Light control switch head,
dimmer switch high
Below 1 V
2B-16 (DIM) - Body ground*7 LG - Body ground Headlight high beam signal Light control switch head,
dimmer switch except high
11 to 14 V
2B-22 (STP) - Body ground R - Body ground Stop light switch signal Brake pedal depressed 11 to 14 V
2B-22 (STP) - Body ground R - Body ground Stop light switch signal Brake pedal released Below 1 V
2D-29 (DOMR) - Body ground*8 R - Body ground Battery save system (interior light auto cut function) signal Battery save system (interior light auto cut function) operating 11 to 14 V
2D-29 (DOMR) - Body ground*8 R - Body ground Battery save system (interior light auto cut function) signal Battery save system (interior light auto cut function) not operating Below 1 V

*1: w/ Front Fog Light

*2: w/ Daytime Running Light

*3: except G. C. C.

*4: for G. C. C.

*5: except Double Swing Out Type

*6: w/ Rear Fog Light

*7: for Double Swing Out Type

*8: w/ Dome Cut Relay




CHECK HEADLIGHT LEVELING ECU ASSEMBLY (w/ Static Headlight Auto Leveling)


U165769E02
3.344,0.198 3.76,0.375 0.417,0.177 10 false E109

a.

Disconnect the E109 headlight leveling ECU connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
E109-1 (IG) - Body ground R - Body ground Ignition power supply Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
E109-9 (E1) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the E109 headlight leveling ECU connector.


d.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
E109-3 (HDLP) - E109-9 (E1) L - W-B Low beam headlight signal input Low beam headlights on Below 1 V
Low beam headlights off 11 to 14 V
E109-5 (INIT) - E109-9 (E1) LG - W-B Initialization signal input Terminal LVL and terminal CG of DLC3 connected Below 1 V
Terminal LVL and terminal CG of DLC3 not connected 4.5 to 5.5 V
E109-6 (WNG) - E109-9 (E1) L - W-B Warning indicator drive output Warning indicator on Below 1 V
Warning indicator off 11 to 14 V
E109-10 (RH+) - E109-9 (E1) G - W-B Headlight leveling motor RH power supply Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
E109-11 (LH+) - E109-9 (E1) R - W-B Headlight leveling motor LH power supply Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
E109-12 (SBR) - E109-21 (SGR) L - P Rear height control sensor power supply Ignition switch off Below 1 V
Ignition switch ON 4.75 to 5.25 V
E109-16 (SPDR) - E109-9 (E1) V - W-B Vehicle speed signal input Vehicle is driven at approximately 20 km/h (12 mph) Pulse generation
(See waveform 1)
E109-17 (RHT) - E109-9 (E1) P - W-B Headlight leveling motor RH operation signal input With low beam headlights on, vehicle height not changed Below 1 V
With low beam headlights on, vehicle height changed and maintained for more than 3 seconds 1.0 to 14.4 V
E109-18 (LHT) - E109-9 (E1) G - W-B Headlight leveling motor LH operation signal input With low beam headlights on, vehicle height not changed Below 1 V
With low beam headlights on, vehicle height changed and maintained for more than 3 seconds 1.0 to 14.4 V
E109-19 (SHRL) - E109-21 (SGR) SB - P Rear height control sensor signal input Ignition switch off Below 1 V
Ignition switch ON 0.5 to 4.5 V
E109-21 (SGR) - E109-9 (E1) P - W-B Rear height control sensor ground Always Below 1 Ω
E109-23 (RH-) - E109-9 (E1) BR - W-B Headlight leveling motor RH ground Always Below 1 Ω
E109-24 (LH-) - E109-9 (E1) V - W-B Headlight leveling motor LH ground Always Below 1 Ω

i.
U111616E02
0.76,1.573 1.292,1.573 false 0.677,0.698 0.677,1.76 false 1.385,0.708 1.385,1.76 false 0.938,1.573 1.156,1.74 0.219,0.167 10 false (A)

Waveform 1

Item Content
Terminal No. (Symbol) E109-16 (SPDR) - E109-9 (E1)
Tool setting 5 V/DIV., 20 ms./DIV.
Condition Vehicle is driven at approximately 20 km/h (12 mph)

HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.





CHECK HEADLIGHT SWIVEL ECU ASSEMBLY (w/ Dynamic Headlight Auto Leveling)


U166466E02
3.406,0.385 3.76,0.552 0.354,0.167 10 false E101

a.

Disconnect the E101 headlight swivel ECU connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
E101-15 (IG) - Body ground R - Body ground Ignition power supply Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
E101-22 (E1) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the E101 headlight swivel ECU connector.


d.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
E101-3 (LHT) - E101-22 (E1) R - W-B Headlight leveling motor LH power supply Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
E101-4 (RHT) - E101-22 (E1) G - W-B Headlight leveling motor RH power supply Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
E101-7 (INIT) - E101-22 (E1) LG - W-B Initialization signal Ignition switch ON, terminals LVL and GND of DLC3 connected Below 1 V
Ignition switch ON, terminals LVL and GND of DLC3 not connected 4.5 to 5.5 V
E101-11 (RH+) - E101-22 (E1) P - W-B Headlight leveling motor RH LIN communication Ignition switch off Below 1 V
Ignition switch ON Pulse generation
E101-17 (SHFL) - E101-22 (E1)*1 GR - W-B Vehicle height signal Ignition switch off Below 1 V
Ignition switch ON Approximately 2.5 V (When vehicle level)
(The value changes according to the vehicle height)
E101-18 (SBR) - E101-22 (E1)*1 L - W-B Vehicle height signal Ignition switch off Below 1 V
Ignition switch ON 4.5 to 5.5 V
E101-18 (SBR) - E101-21 (SGR)*2 L - P Rear height control sensor LH power supply Ignition switch off Below 1 V
Ignition switch ON 4.5 to 5.5 V
E101-19 (SHRL) - E101-22 (E1)*1 SB - W-B Vehicle height signal Ignition switch off Below 1 V
Ignition switch ON Approximately 2.5 V (When vehicle level)
(The value changes according to the vehicle height)
E101-19 (SHRL) - E101-21 (SGR)*2 SB - P Rear height control sensor LH signal Ignition switch off Below 1 V
Ignition switch ON Approximately 2.5 V (When vehicle level)
(The value changes according to the vehicle height)
E101-21 (SGR) - E101-22 (E1)*1 P - W-B Vehicle height signal Always Below 1 Ω
E101-21 (SGR) - E101-22 (E1)*2 P - W-B Rear height control sensor LH ground Always Below 1 Ω
E101-27 (LH-) - E101-22 (E1) V - W-B Headlight leveling motor LH ground Always Below 1 Ω
E101-28 (RH-) - E101-22 (E1) BR - W-B Headlight leveling motor RH ground Always Below 1 Ω
E101-30 (LH+) - E101-22 (E1) G - W-B Headlight leveling motor LH LIN communication Ignition switch off Below 1 V
Ignition switch ON Pulse generation

*1: w/ Active Height Control Suspension

*2: w/o Active Height Control Suspension




CHECK NO. 2 MAIN BODY ECU (w/ Side Step Light)


U164935E02
4.135,0.781 4.417,0.958 0.281,0.177 10 false L51 2.917,0.781 3.198,0.958 0.281,0.177 10 false L50

a.

Disconnect the L50 and L51 ECU connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L50-14 (BECU) - Body ground R - Body ground Battery power supply Always 11 to 14 V
L50-13 (SIG) - Body ground G - Body ground Ignition power supply Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
L50-7 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
L51-7 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.



c.

Reconnect the L50 and L51 ECU connectors.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L50-9 (RBD1) - Body ground L - Body ground Step light LH signal Step light LH on Below 1 V
Step light LH off 11 to 14 V
L50-21 (RBD2) - Body ground L - Body ground Step light RH signal Step light RH on Below 1 V
Step light RH off 11 to 14 V



CHECK INNER REAR VIEW MIRROR ASSEMBLY (w/ Automatic High Beam System)


U166380E02
3.479,0.313 3.823,0.479 0.344,0.167 10 false R16

a.

Disconnect the R16 mirror connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
R16-1 (IG) - Body ground G - Body ground IG power supply Ignition switch ON 11 to 14 V
R16-2 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the R16 mirror connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
R16-10 (LIN) - R16-2 (E) B - W-B LIN communication Automatic high beam system operates Pulse generation (See waveform 1)

i.
E177995E01
2.857,1.753 3.208,1.908 0.350,0.156 10 GND

Waveform 1

Item Content
Terminal No. (Symbol) R16-10 (LIN) - R16-2 (E)
Tool setting 2 V/DIV., 20 ms./DIV.
Condition Automatic high beam system operates