Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052855 LIGHTING (EXT) _0255811 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Taillight Circuit  


DESCRIPTION

The main body ECU receives a light control switch information signal from the headlight dimmer switch, and illuminates the taillights.

WIRING DIAGRAM

E233674E03
3.81,0.801 4.015,0.964 0.205,0.163 10 2A 3.812,1.884 4.017,2.047 0.205,0.163 10 2C 3.851,0.632 3.951,0.788 0.100,0.156 10 1 3.833,1.703 4.022,1.859 0.189,0.156 10 22 5.135,2.061 5.450,2.203 0.316,0.142 10 TAIL 4.916,1.565 5.627,1.734 0.711,0.170 10 TAIL Relay 5.834,3.174 6.851,3.323 1.017,0.149 10 Main Body ECU 0.5,0.787 1.309,0.956 0.809,0.170 10 from Battery 0.922,3.227 1.048,3.401 0.126,0.174 10 6 1.084,3.227 1.199,3.369 0.114,0.142 10 E 0.908,3.897 2.509,4.233 1.601,0.336 10 Rear Combination Light Assembly RH 0.917,3.739 1.231,3.941 0.313,0.202 10 Y1 1.914,3.22 2.228,3.422 0.313,0.202 10 TL 2.152,3.216 2.340,3.372 0.189,0.156 10 5 0.918,1.809 1.023,1.961 0.105,0.151 10 4 1.112,1.809 1.226,1.951 0.114,0.142 10 E 0.908,2.448 2.444,2.813 1.536,0.365 10 Rear Combination Light Assembly LH 0.917,2.289 1.231,2.491 0.313,0.202 10 n1 1.874,1.802 2.188,2.004 0.313,0.202 10 TL 2.144,1.794 2.332,1.950 0.189,0.156 10 5 0.141,0.147 2.644,0.460 2.503,0.313 12 for Double Swing Out Type: 5.994,0.813 6.376,0.977 0.382,0.164 10 TRLY

E233673E02
3.822,0.788 4.027,0.951 0.205,0.163 10 2A 3.825,1.872 4.029,2.035 0.205,0.163 10 2C 3.863,0.619 3.963,0.775 0.100,0.156 10 1 3.845,1.69 4.034,1.846 0.189,0.156 10 22 5.147,2.049 5.463,2.191 0.316,0.142 10 TAIL 4.928,1.552 5.640,1.722 0.711,0.170 10 TAIL Relay 5.846,3.161 6.863,3.310 1.017,0.149 10 Main Body ECU 0.513,0.774 1.321,0.944 0.809,0.170 10 from Battery 1.054,5.641 1.159,5.793 0.105,0.151 10 1 0.92,6.268 2.535,6.449 1.614,0.181 10 Rear Light Assembly RH 0.93,6.109 1.243,6.311 0.313,0.202 10 S12 2.061,5.626 2.249,5.782 0.189,0.156 10 3 1.054,4.363 1.159,4.514 0.105,0.151 10 1 0.92,4.993 2.465,5.195 1.545,0.202 10 Rear Light Assembly LH 0.93,4.834 1.243,5.036 0.313,0.202 10 S11 2.061,4.347 2.249,4.503 0.189,0.156 10 3 1.054,3.076 1.159,3.227 0.105,0.151 10 3 1.208,3.075 1.322,3.217 0.114,0.142 10 E 0.92,3.611 2.417,3.930 1.496,0.319 10 Rear Combination Light Assembly RH 0.93,3.452 1.243,3.654 0.313,0.202 10 L3 1.831,3.068 2.144,3.271 0.313,0.202 10 TL 2.061,3.06 2.249,3.216 0.189,0.156 10 6 1.054,1.797 1.159,1.948 0.105,0.151 10 3 1.208,1.796 1.322,1.938 0.114,0.142 10 E 0.92,2.312 2.438,2.657 1.517,0.345 10 Rear Combination Light Assembly LH 0.93,2.153 1.243,2.355 0.313,0.202 10 K4 1.831,1.79 2.144,1.992 0.313,0.202 10 TL 2.061,1.782 2.249,1.937 0.189,0.156 10 6 0.153,0.134 2.656,0.447 2.503,0.313 12 except Double Swing Out Type: 6.03,0.791 6.411,0.961 0.382,0.170 10 TRLY

PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TAILLIGHT RELAY)
a.

Operate the intelligent tester according to the steps on the display and select "Active Test".

Main Body
Tester Display Test Part Control Range Diagnostic Note
Taillight Relay Taillight ON or OFF -

OK:

Taillight turns on/turns off.




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT FUSE (TAIL FUSE)
2.INSPECT FUSE (TAIL FUSE)
a.

Remove the TAIL fuse from the main body ECU.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
TAIL fuse Always Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY)

NG

REPLACE FUSE

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY)
a.
U165938E02
0.052,0.063 2.458,0.438 2.406,0.375 10 false Front view of wire harness connector: (to Main Body ECU) 0.51,1.302 0.698,1.448 0.188,0.146 10 false 2A

Disconnect the 2A ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2A-1 - Body ground Always 11 to 14 V




OK

4.CHECK VEHICLE TYPE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK VEHICLE TYPE
a.

Check the vehicle type.

Result
Result Proceed to
for Double Swing Out Type A
except Double Swing Out Type B



A

5.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT - MAIN BODY ECU AND BODY GROUND)

B

6.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT - MAIN BODY ECU AND BODY GROUND)
5.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT - MAIN BODY ECU AND BODY GROUND)
a.

Disconnect the 2C ECU connector.

U166224E02
5.448,1.625 5.75,2.177 false 4.99,1.656 4.719,2.208 false 5.219,1.646 5.26,2.198 false 0.76,0.063 3.094,0.417 2.333,0.354 10 false Front view of wire harness connector: (to Main Body ECU) 4.417,0.063 6.75,0.417 2.333,0.354 10 false Front view of wire harness connector: (to Rear Combination Light) 4.385,1.104 4.625,1.302 0.24,0.198 10 false *1 4.406,1.563 4.625,1.792 0.219,0.229 10 false *2 0.229,1.365 0.49,1.542 0.26,0.177 10 false 2C 4.042,1.125 4.302,1.354 0.26,0.229 10 false n1 4.031,1.563 4.313,1.802 0.281,0.24 10 false Y1 5.656,2.208 5.979,2.375 0.323,0.167 10 false E*2 5.188,2.24 5.385,2.406 0.198,0.167 10 false TL 4.594,2.229 4.906,2.438 0.313,0.208 10 false E*1 0.177,2.385 0.844,2.615 0.667,0.229 10 false *2: for RH 0.177,2.125 0.844,2.354 0.667,0.229 10 false *1: for LH


b.

for LH:

i.

Disconnect the n1 light connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2C-22 - n1-5 (TL) Always Below 1 Ω
n1-4 (E) - Body ground
n1-5 (TL) - Body ground Always 10 kΩ or higher




c.

for RH:

i.

Disconnect the Y1 light connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2C-22 - Y1-5 (TL) Always Below 1 Ω
Y1-6 (E) - Body ground
Y1-5 (TL) - Body ground Always 10 kΩ or higher





OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT - MAIN BODY ECU AND BODY GROUND)
a.

Disconnect the 2C ECU connector.

U165939E02
5.635,1.667 6.073,1.667 false 4.948,1.667 4.948,2.094 false 0.677,0.135 3.01,0.49 2.333,0.354 10 false Front view of wire harness connector: (to Main Body ECU) 4.385,0.115 6.719,0.469 2.333,0.354 10 false Front view of wire harness connector: (to Rear Combination Light) 4.375,1.125 4.615,1.323 0.24,0.198 10 false *1 4.396,1.542 4.615,1.729 0.219,0.188 10 false *2 0.24,1.375 0.51,1.563 0.271,0.188 10 false 2C 4.031,1.125 4.313,1.354 0.281,0.229 10 false K4 4.052,1.563 4.333,1.792 0.281,0.229 10 false L3 0.083,2.177 0.802,2.688 0.719,0.51 10 false *1: for LH *2: for RH 6.104,1.583 6.302,1.75 0.198,0.167 10 false TL 4.917,2.115 5.063,2.323 0.146,0.208 10 false E


b.

for LH:

i.

Disconnect the K4 light connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2C-22 - K4-6 (TL) Always Below 1 Ω
K4-3 (E) - Body ground
K4-6 (TL) - Body ground Always 10 kΩ or higher




c.

for RH:

i.

Disconnect the L3 light connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2C-22 - L3-6 (TL) Always Below 1 Ω
L3-3 (E) - Body ground
L3-6 (TL) - Body ground Always 10 kΩ or higher





OK

7.CHECK HARNESS AND CONNECTOR (REAR LIGHT - MAIN BODY ECU AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (REAR LIGHT - MAIN BODY ECU AND BODY GROUND)
a.

Disconnect the 2C ECU connector.

U166233E02
0.76,0.063 3.094,0.417 2.333,0.354 10 false Front view of wire harness connector: (to Main Body ECU) 4.417,0.063 6.75,0.417 2.333,0.354 10 false Front view of wire harness connector: (to Rear Light) 4.385,1.125 4.583,1.302 0.198,0.177 10 false *1 4.406,1.583 4.604,1.76 0.198,0.177 10 false *2 0.24,1.375 0.542,1.583 0.302,0.208 10 false 2C 4,1.156 4.344,1.385 0.344,0.229 10 false S11 4,1.563 4.354,1.781 0.354,0.219 10 false S12 0.177,2.385 0.844,2.615 0.667,0.229 10 false *2: for RH 0.177,2.125 0.844,2.354 0.667,0.229 10 false *1: for LH


b.

for LH:

i.

Disconnect the S11 light connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2C-22 - S11-3 Always Below 1 Ω
S11-1 - Body ground
S11-3 - Body ground Always 10 kΩ or higher




c.

for RH:

i.

Disconnect the S12 light connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2C-22 - S12-3 Always Below 1 Ω
S12-1 - Body ground
S12-3 - Body ground Always 10 kΩ or higher





OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR