When a door is opened while the DOOR switch of the map light assembly is on, the map light assembly receives a door open signal from the main body ECU and turns on the corresponding lights.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Operate the GTS according to the steps on the display and select "Active Test".
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Illuminated Entry System | Illumination light | OFF or ON | - |
Light comes on.
OK
NG
Check the vehicle type.
| Result | Proceed to |
|---|---|
| w/o Map Light | A |
| w/ Map Light | B |
A
B
Disconnect the 2J main body ECU connector.
Disconnect the R22 No. 1 room light connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2J-30 (ILE) - R22-2 (CTY) | Always | Below 1 Ω |
| R22-1 (B) - Body ground | ||
| R22-3 (E) - Body ground | ||
| 2J-30 (ILE) - Body ground | Always | 10 kΩ or higher |
Disconnect the R24 No. 1 room light connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2J-30 (ILE) - R24-2 (DL) | Always | Below 1 Ω |
| R24-1 (DB) - Body ground | ||
| R24-3 (L) - Body ground | ||
| 2J-30 (ILE) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the 2J ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R7-16 (+B3) - Body ground | Always | 11 to 14 V |
OK
NG
Remove the map light (See page Vehicle Interior>LIGHTING (INT)>ROOM LIGHT(for Front)>REMOVAL).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| R7-31 (+B1) - R7-5 (RRVT) | Dome light switch off | Below 1 V |
| Dome light switch on | 11 to 14 V | |
| R7-6 (RILL) - R7-32 (ILLB) | Dome light switch off | Below 1 V |
| Dome light switch on | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| R7-9 (CTY) - Body ground | "Door" switch on and door open | Below 1 Ω |
| "Door" switch off and door open | 10 kΩ or higher | |
| "Door" switch on and door closed | 10 kΩ or higher | |
| "Door" switch off and door closed | 10 kΩ or higher | |
| R7-17 (GND9) - Body ground | Always | Below 1 Ω |
OK
NG
Disconnect the R7 map light connector.
Disconnect the R23 light connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R7-31 (+B1) - R23-1 (DB) | Always | Below 1 Ω |
| R7-5 (RRVT) - R23-3 (DL) | ||
| R23-2 (L) - Body ground | ||
| R7-31 (+B1) - Body ground | Always | 10 kΩ or higher |
| R7-16 (RRVT) - Body ground |
OK
NG
Check the vehicle type.
| Result | Proceed to |
|---|---|
| w/ Spot light | A |
| w/o Spot light | B |
A
B
Disconnect the R7 map light connector.
Disconnect the R4 light connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R7-32 (ILLB) - R4-1 (B) | Always | Below 1 Ω |
| R7-6 (RILL) - R4-2 (CTY) | ||
| R7-32 (ILLB) - Body ground | Always | 10 kΩ or higher |
| R7-6 (RILL) - Body ground |
for LH:
Disconnect the R8 light connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R7-32 (ILLB) - R8-2 (BL) | Always | Below 1 Ω |
| R7-1 (RGND) - R8-4 (EL) | ||
| R7-32 (ILLB) - Body ground | Always | 10 kΩ or higher |
| R7-1 (RGND) - Body ground |
for RH:
Disconnect the R9 light connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R7-32 (ILLB) - R9-2 (BR) | Always | Below 1 Ω |
| R7-1 (RGND) - R9-4 (ER) | ||
| R7-32 (ILLB) - Body ground | Always | 10 kΩ or higher |
| R7-1 (RGND) - Body ground |
OK
NG
Disconnect the R7 map light connector.
Disconnect the R21 light connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R7-32 (ILLB) - R21-1 (B) | Always | Below 1 Ω |
| R7-6 (RILL) - R21-3 (CTY) | ||
| R21-2 (E) - R7-1 (RGND) | ||
| R7-32 (ILLB) - Body ground | Always | 10 kΩ or higher |
| R7-6 (RILL) - Body ground |
OK
NG