Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052855 LIGHTING (EXT) _0255811 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Headlight Leveling ECU Power Source Circuit  


DESCRIPTION

This circuit detects the state of the ignition switch, and sends it to the headlight leveling ECU*1 or headlight swivel ECU*2.

*1: w/ Static Headlight Auto Leveling

*2: w/ Dynamic Headlight Auto Leveling


WIRING DIAGRAM

E227418E13
5.104,2.76 6.625,3.104 1.521,0.344 10 false Headlight Leveling ECU Assembly 5.104,2.594 5.51,2.781 0.406,0.188 10 false E109 0.531,1.115 2.031,1.344 1.5,0.229 10 false from IG NO. 4 Relay IG 5.469,1.063 5.667,1.26 0.198,0.198 10 false IG 5.458,2.156 5.656,2.354 0.198,0.198 10 false E1 5.271,2.063 5.375,2.208 0.104,0.146 10 false 9 5.25,0.958 5.375,1.135 0.125,0.177 10 false 1 3.51,1.24 4.396,1.448 0.885,0.208 10 false ECU-IG No. 3 0.188,0.104 2.729,0.385 2.542,0.281 12 false w/ Static Headlight Auto Leveling:

E227418E07
5.099,2.759 6.617,3.100 1.518,0.342 10 Headlight Swivel ECU Assembly 5.099,2.598 5.723,2.784 0.624,0.186 10 E101 0.572,1.069 1.994,1.306 1.422,0.237 10 from IG NO. 4 Relay 5.468,1.063 5.663,1.263 0.195,0.200 10 IG 5.463,2.153 5.658,2.352 0.195,0.200 10 E1 5.211,2.061 5.394,2.211 0.184,0.150 10 22 5.211,0.963 5.409,1.142 0.199,0.179 10 15 3.359,1.264 4.345,1.474 0.986,0.210 10 ECU-IG No. 3 0.165,0.08 3.171,0.360 3.006,0.279 12 w/ Dynamic Headlight Auto Leveling:

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After replacing the headlight leveling ECU*1 or headlight swivel ECU*2, initialization of the ECU is necessary (except w/ Dynamic Headlight Auto Leveling) (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>INITIALIZATION).


*1: w/ Static Headlight Auto Leveling

*2: w/ Dynamic Headlight Auto Leveling



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check the vehicle type.

Result
Result Proceed to
w/ Static Headlight Auto Leveling A
w/ Dynamic Headlight Auto Leveling B



A

2.READ VALUE USING INTELLIGENT TESTER (IGNITION POWER SUPPLY)

B

4.READ VALUE USING INTELLIGENT TESTER (IGNITION POWER SUPPLY)
2.READ VALUE USING INTELLIGENT TESTER (IGNITION POWER SUPPLY)
a.

Using the intelligent tester, read the Data List (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST).

HL Auto Leveling
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
+B Ignition power supply voltage value / 0 to 19.75 V 11 to 14 V -

OK:

The display is as specified in the normal condition column.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - BATTERY AND BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - BATTERY AND BODY GROUND)
a.
U165792E01
0.133,0.046 0.434,0.278 0.301,0.232 10 *a 0.185,0.625 0.559,0.788 0.374,0.163 10 E109 3.043,1.856 3.270,2.019 0.227,0.163 10 E1 0.273,1.856 0.500,2.019 0.227,0.163 10 IG 0.68,1.32 0.41,1.821 false 2.794,1.296 3.043,1.856 false

Disconnect the headlight leveling ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E109-1 (IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E109-9 (E1) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Headlight Leveling ECU Assembly)


OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING INTELLIGENT TESTER (IGNITION POWER SUPPLY)
a.

Using the intelligent tester, read the Data List (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST).

AFS
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
+B Ignition power supply voltage value / 0 to 19.75 V 11 to 14 V -

OK:

The display is as specified in the normal condition column.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

5.CHECK HARNESS AND CONNECTOR (HEADLIGHT SWIVEL ECU ASSEMBLY - BATTERY AND BODY GROUND)
5.CHECK HARNESS AND CONNECTOR (HEADLIGHT SWIVEL ECU ASSEMBLY - BATTERY AND BODY GROUND)
a.
U165787E01
0.054,0.036 0.238,0.218 0.184,0.182 10 *a 1.862,1.922 2.091,2.089 0.229,0.166 10 E1 1.603,1.545 1.84,1.955 false 1.613,0.517 1.985,0.686 0.372,0.170 10 E101 0.867,1.922 1.095,2.089 0.229,0.166 10 IG 0.884,1.905 0.56,1.537 false

Disconnect the headlight leveling ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E101-15 (IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E101-22 (E1) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Headlight Swivel ECU Assembly)

Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C


A

REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY

B

REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR