Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052855 LIGHTING (EXT) _0255811 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Rear Fog Light Circuit  


DESCRIPTION

The main body ECU receives a rear fog light switch information signal from the light control switch (rear fog switch), and illuminates the rear fog lights.

WIRING DIAGRAM

E159799E01
0.959,3.519 2.791,3.941 1.832,0.422 10 O6 Rear Fog Light Assembly LH 3.404,3.519 5.340,3.860 1.936,0.341 10 O5 Rear Fog Light Assembly RH 4.406,2.739 5.022,2.899 0.617,0.161 10 RR FOG 3.94,0.376 4.082,0.536 0.142,0.161 10 1 3.94,2.759 4.082,2.919 0.142,0.161 10 8 0.872,0.542 1.690,0.721 0.818,0.179 10 from Battery 4.871,1.591 5.204,1.770 0.333,0.179 10 TAIL 3.888,0.563 4.141,0.719 0.253,0.156 10 2A 3.899,2.954 4.153,3.110 0.253,0.156 10 2C 6.105,2.121 6.577,2.271 0.472,0.150 10 RFGO 6.105,0.556 6.577,0.706 0.472,0.150 10 TRLY 5.822,3.449 6.849,3.591 1.026,0.142 10 Main Body ECU 3.261,3.836 3.399,4.009 0.139,0.173 10 1 3.265,3.422 3.412,3.625 0.147,0.203 10 2 0.818,3.832 0.957,4.006 0.139,0.173 10 1 0.819,3.417 0.966,3.620 0.147,0.203 10 2

PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Operate the intelligent tester according to the steps on the display and select "Active Test".

Main Body
Tester Display Test Part Control Range Diagnostic Note
Rear Fog Light Relay Rear fog light ON or OFF -

OK:

Fog light turns on/turns off.




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT FUSE (RR FOG, TAIL)
2.INSPECT FUSE (RR FOG, TAIL)
a.

Remove the RR FOG fuse and TAIL fuse from the main body ECU.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
RR FOG fuse Always Below 1 Ω
TAIL fuse




OK

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BODY GROUND)

NG

REPLACE FUSE

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BODY GROUND)
a.
U165938E02
0.052,0.063 2.458,0.438 2.406,0.375 10 false Front view of wire harness connector: (to Main Body ECU) 0.51,1.302 0.698,1.448 0.188,0.146 10 false 2A

Disconnect the 2A ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2A-1 - Body ground Always 11 to 14 V




OK

4.CHECK HARNESS AND CONNECTOR (REAR FOG LIGHT ASSEMBLY - MAIN BODY ECU AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (REAR FOG LIGHT ASSEMBLY - MAIN BODY ECU AND BODY GROUND)
a.

Disconnect the 2C ECU connector.

U166031E02
2.521,1.219 2.719,0.927 false 0.719,0.198 3.531,0.646 2.813,0.448 10 false Front view of wire harness connector: (to Main Body ECU) 4.021,0.135 6.802,0.573 2.781,0.438 10 false Front view of wire harness connector: (to Rear Fog Light Assembly) 4.125,1.156 4.396,1.333 0.271,0.177 10 false O6 4.115,1.469 4.406,1.677 0.292,0.208 10 false O5 0.323,1.302 0.625,1.521 0.302,0.219 10 false 2C 4.396,1.042 4.625,1.25 0.229,0.208 10 false *1 4.458,1.438 4.688,1.635 0.229,0.198 10 false *2 6.083,1.854 6.875,2.094 0.792,0.24 10 false *1: for LH 2.771,0.844 3.229,1.031 0.458,0.188 10 false RFGO 6.104,2.25 6.896,2.49 0.792,0.24 10 false *2: for RH


b.

for LH:

i.

Disconnect the O6 rear fog light connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2C-8 (RFGO) - O6-2 Always Below 1 Ω
O6-1 - Body ground
O6-2 - Body ground Always 10 kΩ or higher




c.

for RH:

i.

Disconnect the O5 rear fog light connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2C-8 (RFGO) - O5-2 Always Below 1 Ω
O5-1 - Body ground
O5-2 - Body ground Always 10 kΩ or higher





OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR