Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › from 2015.08
RM2660E _59 Vehicle Exterior _052855 LIGHTING (EXT) _0255811 LIGHTING SYSTEM U

LIGHTING (EXT)  LIGHTING SYSTEM  FAIL-SAFE CHART  


Automatic Headlight Beam Level Control System (w/ Static Headlight Auto Leveling)


a.

The headlight leveling ECU operates in fail-safe mode if an abnormal condition such as those listed below has been detected.

Item Abnormality Detection Condition Return Condition Warning Indicator
Height control sensor power source voltage Abnormal height control sensor power source voltage (4.6 V or less, or 6.25 V or more) is detected. Voltage of 4.61 to 6.24 V is detected Illuminated
Height control sensor signal voltage Abnormal height control sensor signal voltage (0.25 V or less, or 4.75 V or more) is detected. Voltage of 0.26 to 4.74 V is detected
High power source voltage Abnormal high power source voltage (18.5 V or more) is detected. Voltage of 17.5 V or less is detected Not illuminated
Low power source voltage Abnormal low power source voltage (9.0 V or less) is detected. Voltage of 9.3 V or more is detected Not illuminated
Abnormal height control sensor signal while initialization Initialization is performed outside the valid range of the voltage for initialization. Initialization is successfully completed within the valid range of the voltage for initialization. Illuminated



Automatic Headlight Beam Level Control System (w/ Dynamic Headlight Auto Leveling)


If the headlight swivel ECU detects a malfunction in the automatic headlight beam level control system, it will take the actions indicated in the table below.

Malfunctioning Part Detection Condition Fail-safe Control Warning Indicator
Speed Sensor Speed sensor signal malfunction Continues control. Illuminated
Rear Height Control Sensor LH (w/o Active Height Control Suspension) Rear height control sensor LH signal malfunction
·

Stops operation after returning the headlight leveling motor to the initial position (system fails when the headlight leveling motor is higher than the initial position).

·

Stops operation with the headlight leveling motor at the current position (system fails when the headlight leveling motor is lower than the initial position).


Illuminated
Source voltage malfunction
Height Control Sensor Signal (w/ Active Height Control Suspension) Height control sensor signal malfunction
·

Stops operation after returning the headlight leveling motor to the initial position (system fails when the headlight leveling motor is higher than the initial position).

·

Stops operation with the headlight leveling motor at the current position (system fails when the headlight leveling motor is lower than the initial position).


Illuminated
Headlight Leveling Motor Headlight leveling motor communication error Abnormal side headlight leveling motor:
·

Stops operation after returning the headlight leveling motor to the initial position (system fails when the headlight leveling motor is higher than the initial position).

·

Stops operation with the headlight leveling motor at the current position (system fails when the headlight leveling motor is lower than the initial position).


Normal side headlight leveling motor:
·

Stops operation after returning the headlight leveling motor to the initial position (system fails when the headlight leveling motor is higher than the initial position).

·

Stops operation with the headlight leveling motor at the current position (system fails when the headlight leveling motor is lower than the initial position).


Illuminated
Headlight leveling motor malfunction
·

Open in circuit

·

Short in circuit

·

Overheated


Abnormal side headlight leveling motor:
·

Stops at the current position.


Normal side headlight leveling motor:
·

Stops operation after returning the headlight leveling motor to the initial position (system fails when the headlight leveling motor is higher than the initial position).

·

Stops operation with the headlight leveling motor at the current position (system fails when the headlight leveling motor is lower than the initial position).


Headlight Leveling Motor Voltage malfunction Abnormal side headlight leveling motor:
·

Stops at the current position.


Normal side headlight leveling motor:
·

Stops operation after returning the headlight leveling motor to the initial position (system fails when the headlight leveling motor is higher than the initial position).

·

Stops operation with the headlight leveling motor at the current position (system fails when the headlight leveling motor is lower than the initial position).


Not illuminated
CAN Communication System Vehicle specifications unconfirmed
(Main body ECU)
Continues control. Illuminated
Communication signal malfunction
(Main body ECU)
Communication signal malfunction
(Skid control ECU)
Judges that the vehicle speed is 0 km/h (0 mph) and continues control.
Headlight Swivel ECU Vehicle specifications unconfirmed Continues control. Illuminated
Rear height control sensor LH initialization unconfirmed Both headlight leveling motors:
·

Stop at the same position as when the vehicle is empty.


Blinks 6 times at 2 Hz after the ignition switch is turned from off to ON


AUTOMATIC HIGH BEAM SYSTEM (w/ Automatic High Beam System)


a.

The main body ECU operates in fail-safe mode if an abnormal condition, such as those listed below, has been detected.

Item Abnormality Detection Condition Return Condition Warning Indicator
Speed Sensor Signal Malfunction Abnormal speed sensor signal is detected. Normal speed sensor signal is detected. Flashes
CAN Communication Signal Malfunction Abnormal CAN communication signal is detected. Normal CAN communication signal is detected. Flashes
Automatic High Beam Sensor Abnormal communication signal is detected. Normal communication signal is detected. Flashes