Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052855 LIGHTING (EXT) _0255811 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Headlight (HI-BEAM) Circuit  


DESCRIPTION

The main body ECU receives a headlight hi switch information signal from the light control switch, and illuminates the headlight high beam.

WIRING DIAGRAM

E286790E02
0.75,0.865 1.635,1.083 0.885,0.219 10 false from Battery 2.771,0.781 2.979,1.01 0.208,0.229 10 false 2 3.458,0.771 3.667,1 0.208,0.229 10 false 1 2.75,1.219 2.958,1.448 0.208,0.229 10 false 3 3.49,1.219 3.635,1.406 0.146,0.188 10 false 5 4.896,0.719 5.104,0.948 0.208,0.229 10 false 16 5.177,0.781 5.688,1.01 0.51,0.229 10 false DIM*1 5.177,0.948 5.677,1.198 0.5,0.25 10 false DRL*2 2.865,1.604 3.677,1.854 0.813,0.25 10 false HEAD HI 4.958,1.802 5.167,2.031 0.208,0.229 10 false 2B 4.99,1.979 6.51,2.406 1.521,0.427 10 false Main Body ECU (Cowl Side Junction Block LH) 1.521,2.146 2.021,2.333 0.5,0.188 10 false 1*3, *4 1.542,2.323 1.865,2.531 0.323,0.208 10 false 4*5 2.146,2.302 2.313,2.5 0.167,0.198 10 false 2 1.177,2.677 1.604,2.896 0.427,0.219 10 false A2*3 2.938,2.646 3.719,2.865 0.781,0.219 10 false HEAD LH 1.198,2.854 1.667,3.063 0.469,0.208 10 false A40*4 1.198,3.052 1.656,3.271 0.458,0.219 10 false A53*5 1.198,3.25 3.01,3.479 1.813,0.229 10 false Headlight Unit Assembly LH 2.99,4.167 3.75,4.396 0.76,0.229 10 false HEAD RH 1.51,3.708 2.073,3.906 0.563,0.198 10 false 1*3, *4 1.531,3.885 1.896,4.083 0.365,0.198 10 false 4*5 2.115,3.844 2.323,4.073 0.208,0.229 10 false 2 1.281,4.198 1.75,4.406 0.469,0.208 10 false A11*3 1.292,4.385 1.729,4.604 0.438,0.219 10 false A41*4 1.292,4.594 1.76,4.833 0.469,0.24 10 false A57*5 1.271,4.792 3.26,5.031 1.99,0.24 10 false Headlight Unit Assembly RH 0.125,5.135 2.167,5.333 2.042,0.198 10 false *1: w/o Daytime Running Light 0.135,5.438 2.177,5.635 2.042,0.198 10 false *2: w/ Daytime Running Light 0.146,5.74 2.188,5.938 2.042,0.198 10 false *3: for Halogen Type Clearance Light 0.135,6.031 2.177,6.229 2.042,0.198 10 false *4: for HID Type 0.146,6.333 2.188,6.531 2.042,0.198 10 false *5: for LED Type Clearance Light

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (HEAD HI RELAY)
a.

Using the intelligent tester, perform the Active Test (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST).

Main Body
Tester Display Test Part Control Range Diagnostic Note
Head Light Hi Headlight (Hi) ON or OFF -

OK:

Headlight high beam turns on/turns off.




OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

NG

2.INSPECT HEADLIGHT RELAY (HEAD HI)
2.INSPECT HEADLIGHT RELAY (HEAD HI)
a.
E247660E01
2.851,0.206 3.006,0.376 0.156,0.170 10 1 0.409,1.173 0.565,1.343 0.156,0.170 10 2 1.699,0.974 1.855,1.144 0.156,0.170 10 3 0.397,0.781 0.493,0.928 0.096,0.147 10 3 2.428,1.766 2.584,1.936 0.156,0.170 10 2 1.326,1.173 1.481,1.343 0.156,0.170 10 1 3.206,0.968 3.362,1.138 0.156,0.170 10 5 1.303,0.78 1.408,0.929 0.105,0.149 10 5 2.444,0.695 2.787,0.321 false 2.856,1.054 3.177,1.054 false 2.085,1.054 1.836,1.054 false 2.49,1.413 2.49,1.766 false

Remove the headlight relay from the engine room relay block, junction block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage applied to terminals 1 and 2 Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (BATTERY - HEADLIGHT RELAY [HEAD HI])

NG

REPLACE HEADLIGHT RELAY (HEAD HI)

3.CHECK HARNESS AND CONNECTOR (BATTERY - HEADLIGHT RELAY [HEAD HI])
a.
E160869E05
0.156,0.135 0.427,0.385 0.271,0.25 10 false *a

Remove the headlight relay from the engine room relay block, junction block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Headlight relay terminal 2 - Body ground Always 11 to 14 V
Headlight relay terminal 3 - Body ground


Text in Illustration
*a Front view of wire harness connector
(to Headlight Relay [HEAD HI])



OK

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [HEAD HI] - MAIN BODY ECU [COWL SIDE JUNCTION BLOCK LH])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [HEAD HI] - MAIN BODY ECU [COWL SIDE JUNCTION BLOCK LH])
a.

Remove the headlight relay from the engine room relay block, junction block.


b.

Disconnect the 2B main body ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Headlight relay terminal 1 - 2B-16 (DIM) Always Below 1 Ω
Headlight relay terminal 1 - Body ground Always 10 kΩ or higher




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR