Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052855 LIGHTING (EXT) _0255811 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  License Plate Light Circuit  


DESCRIPTION

When the light switch TAIL signal is received from the cowl side junction block ECU, the license plate light illuminates.

WIRING DIAGRAM

E234119E03
0.521,0.792 1.406,1.042 0.885,0.25 10 false from Battery 3.802,0.823 4.083,1.01 0.281,0.188 10 false 2A 3.844,0.615 4.021,0.813 0.177,0.198 10 false 1 3.813,1.969 4.083,2.156 0.271,0.188 10 false 22 3.792,2.135 4.052,2.323 0.26,0.188 10 false 2C 5.094,1.563 5.458,1.802 0.365,0.24 10 false TAIL 5.115,2.271 5.49,2.5 0.375,0.229 10 false TAIL 6,0.802 6.448,1.031 0.448,0.229 10 false TRLY 5.854,3.135 6.927,3.365 1.073,0.229 10 false Main Body ECU 3.438,7.531 3.604,7.708 0.167,0.177 10 false 2 2.469,7.531 2.635,7.719 0.167,0.188 10 false 1 2.313,7.958 4.479,8.188 2.167,0.229 10 false License Plate Light Assembly RH 2.313,7.813 2.615,7.99 0.302,0.177 10 false S2 3.438,6.656 3.625,6.844 0.188,0.188 10 false 2 2.469,6.667 2.635,6.865 0.167,0.198 10 false 1 2.313,7.094 4.667,7.323 2.354,0.229 10 false License Plate Light Assembly LH 2.313,6.938 2.615,7.115 0.302,0.177 10 false S3 3.438,5.104 3.604,5.323 0.167,0.219 10 false 2 2.469,5.104 2.656,5.323 0.188,0.219 10 false 1 0.646,6.156 4.333,6.458 3.688,0.302 12 false except Double Swing Out Type, w/o Tire Carrier: 0.635,4.625 4.198,4.948 3.563,0.323 12 false except Double Swing Out Type, w/ Tire Carrier: 2.313,5.594 4.24,5.823 1.927,0.229 10 false License Plate Light Assembly 2.313,5.406 2.563,5.625 0.25,0.219 10 false h2 3.438,3.583 3.594,3.76 0.156,0.177 10 false 2 2.469,3.583 2.646,3.823 0.177,0.24 10 false 1 0.646,3.063 2.76,3.302 2.115,0.24 12 false for Double Swing Out Type: 2.313,4.052 4.219,4.281 1.906,0.229 10 false License Plate Light Assembly 2.313,3.885 2.604,4.104 0.292,0.219 10 false W2 3.281,3.594 3.521,3.813 0.24,0.219 10 false E 2.615,3.573 2.792,3.76 0.177,0.188 10 false B

PROCEDURE

1.INSPECT FUSE (TAIL FUSE)
a.

Remove the TAIL fuse from the main body ECU.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
TAIL fuse Always Below 1 Ω




OK

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY)

NG

REPLACE FUSE

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY)
a.

Disconnect the 2A ECU connector.


U165938E02
0.052,0.063 2.458,0.438 2.406,0.375 10 false Front view of wire harness connector: (to Main Body ECU) 0.51,1.302 0.698,1.448 0.188,0.146 10 false 2A

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2A-1 - Body ground Always 11 to 14 V




OK

3.CHECK VEHICLE TYPE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK VEHICLE TYPE
a.

Check the vehicle type.

Result
Result Proceed to
for Double Swing Out Type A
except Double Swing Out Type, w/ Tire Carrier B
except Double Swing Out Type, w/o Tire Carrier C



A

4.CHECK HARNESS AND CONNECTOR (LICENSE PLATE LIGHT - MAIN BODY ECU AND BODY GROUND)

B

5.CHECK HARNESS AND CONNECTOR (LICENSE PLATE LIGHT - MAIN BODY ECU AND BODY GROUND)

C

6.CHECK HARNESS AND CONNECTOR (LICENSE PLATE LIGHT - MAIN BODY ECU AND BODY GROUND)
4.CHECK HARNESS AND CONNECTOR (LICENSE PLATE LIGHT - MAIN BODY ECU AND BODY GROUND)
U166234E01
0.434,0.108 2.799,0.487 2.364,0.378 10 Front view of wire harness connector: (to License Plate Light) 3.996,0.108 6.360,0.487 2.364,0.378 10 Front view of wire harness connector: (to Main Body ECU) 3.372,1.503 3.583,1.678 0.211,0.174 10 2C 0.559,1.459 0.845,1.634 0.286,0.174 10 W2 1.894,2.002 2.111,2.195 0.217,0.193 10 B 0.743,2.002 0.960,2.195 0.217,0.193 10 E 1.236,1.561 0.867,2.002 false 1.526,1.588 1.877,1.985 false

a.

Disconnect the 2C ECU connector.


b.

Disconnect the W2 light connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2C-22 - W2-1 (B) Always Below 1 Ω
W2-2 (E) - Body ground
W2-1 (B) - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (LICENSE PLATE LIGHT - MAIN BODY ECU AND BODY GROUND)
U166235E02
0.438,0.094 2.802,0.469 2.365,0.375 10 false Front view of wire harness connector: (to License Plate Light) 4,0.094 6.365,0.469 2.365,0.375 10 false Front view of wire harness connector: (to Main Body ECU) 3.354,1.531 3.604,1.75 0.25,0.219 10 false 2C 0.583,1.5 0.844,1.677 0.26,0.177 10 false h2

a.

Disconnect the 2C ECU connector.


b.

Disconnect the h2 light connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2C-22 - h2-1 Always Below 1 Ω
h2-2 - Body ground
h2-1 - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (LICENSE PLATE LIGHT - MAIN BODY ECU AND BODY GROUND)
U165963E01
0.424,0.157 2.788,0.535 2.364,0.378 10 Front view of wire harness connector: (to License Plate Light) 3.985,0.157 6.349,0.535 2.364,0.378 10 Front view of wire harness connector: (to Main Body ECU) 3.48,1.274 3.692,1.448 0.211,0.174 10 2C 0.572,1.481 0.784,1.656 0.211,0.174 10 S2 0.572,1.155 0.784,1.329 0.211,0.174 10 S3 0.886,1.151 1.035,1.320 0.149,0.170 10 *1 0.886,1.508 1.035,1.678 0.149,0.170 10 *2 0.16,1.94 0.788,2.471 0.628,0.531 10 *1: for LH *2: for RH

a.

Disconnect the 2C ECU connector.


b.

for LH:

i.

Disconnect the S3 light connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2C-22 - S3-1 Always Below 1 Ω
S3-2 - Body ground
S3-1 - Body ground Always 10 kΩ or higher




c.

for RH:

i.

Disconnect the S2 light connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2C-22 - S2-1 Always Below 1 Ω
S2-2 - Body ground
S2-1 - Body ground Always 10 kΩ or higher





OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR