Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052855 LIGHTING (EXT) _0255811 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Engine Switch Illumination Circuit  


DESCRIPTION

The engine switch illumination is controlled by the main body ECU. The operation and condition of this control are described below (Light control switch is OFF).

Operation Condition
Fade in When any of the following conditions is met, the engine switch illumination fades in.
·

The key enters any actuation area around the doors when the engine switch is off and all the doors are closed.

·

Any door is opened.

·

Any door is unlocked when the engine switch is off and all the doors are closed.

·

The engine switch is turned from on (ACC) to off when all the doors are closed.


Fade out immediately When either of the following conditions is met, the engine switch illumination fades out.
·

The engine switch is turned from off to on (ACC) or on (IG) when all the doors are closed.

·

All the doors are locked when the engine switch is off.


Illuminate for approximately 15 seconds, and then fade out All the doors are closed when the engine switch is off.

WIRING DIAGRAM

E159828E02
5.542,3.219 6.552,3.573 1.01,0.354 10 false Main Body ECU 2.885,2.854 3.844,3.094 0.958,0.24 10 false Engine Switch 1.865,1.885 2.25,2.094 0.385,0.208 10 false GND 4.292,1.885 4.719,2.094 0.427,0.208 10 false SWIL 5.625,1.792 6.042,1.958 0.417,0.167 10 false SWIL 1.708,1.906 1.896,2.094 0.188,0.188 10 false 5 5.365,1.896 5.573,2.073 0.208,0.177 10 false 25 2.896,2.667 3.229,2.875 0.333,0.208 10 false E18 5.542,3 5.74,3.208 0.198,0.208 10 false E1

PROCEDURE

1.INSPECT ENGINE SWITCH
A109252E98
1.656,0.948 1.656,1.396 false 4.698,1.458 5.875,1.458 false 4.427,1.135 5.802,1.135 false 5.896,1.375 6.375,1.573 0.479,0.198 10 false SWIL 1.281,1.406 2.094,1.646 0.813,0.24 10 false Illumination 5.833,1.042 6.188,1.24 0.354,0.198 10 false GND 3.5,0 6.042,0.344 2.542,0.344 10 false Component without harness connected: (Engine switch)

a.

b.

Apply battery voltage to the engine switch.


c.

Check that the illumination comes on.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 11 (SWIL)
Battery negative (-) → Terminal 5 (GND)
Engine switch illumination comes on




OK

2.CHECK HARNESS AND CONNECTOR (ENGINE SWITCH - MAIN BODY ECU AND BODY GROUND)

NG

2.CHECK HARNESS AND CONNECTOR (ENGINE SWITCH - MAIN BODY ECU AND BODY GROUND)
a.
U165962E02
2.292,4.063 2.688,4.063 false 1.719,1.708 2.667,1.708 false 1.865,1.385 2.646,1.385 false 0.042,0.073 2.375,0.427 2.333,0.354 10 false Front view of wire harness connector: (to Engine Switch) 0.042,2.073 2.417,2.479 2.375,0.406 10 false Front view of wire harness connector: (to Main Body ECU) 0.26,1.385 0.573,1.615 0.313,0.229 10 false E18 0.313,3.708 0.594,3.948 0.281,0.24 10 false E1 2.74,3.99 3.104,4.135 0.365,0.146 10 false SWIL 2.708,1.625 3.073,1.771 0.365,0.146 10 false SWIL 2.719,1.323 3.083,1.469 0.365,0.146 10 false GND

Disconnect the E1 ECU connector.


b.

Disconnect the E18 engine switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E1-11 (SWIL) - E1-25 (SWIL) Always Below 1 Ω
E18-5 (GND) - Body ground
E1-11 (SWIL) - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR