Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › from 2015.08
RM2660E _59 Vehicle Exterior _052855 LIGHTING (EXT) _0255811 LIGHTING SYSTEM C

LIGHTING (EXT)  LIGHTING SYSTEM  B2424  Headlight Leveling Motor LH Communication Malfunction  B2425  Headlight Leveling Motor RH Communication Malfunction  


DESCRIPTION

The headlight leveling motor operates by receiving the signal from the headlight swivel ECU. The headlight swivel ECU detects the headlight leveling motor status using the signal from the headlight leveling motor.

DTC Code DTC Detection Condition Trouble Area
B2424
·

Malfunction in the headlight leveling motor LH.

·

Open or short in the headlight leveling motor LH communication circuit.


·

Headlight swivel ECU assembly

·

Headlight unit assembly LH

·

Headlight leveling motor LH

·

Harness or connector


B2425
·

Malfunction in the headlight leveling motor RH.

·

Open or short in the headlight leveling motor RH communication circuit.


·

Headlight swivel ECU assembly

·

Headlight unit assembly RH

·

Headlight leveling motor RH

·

Harness or connector



WIRING DIAGRAM

E330446E08
0.573,6.469 2.313,6.688 1.74,0.219 10 false : LIN Communication Line 1.365,5.833 1.979,6.031 0.615,0.198 10 false E101 1.344,6 3.646,6.198 2.302,0.198 10 false Headlight Swivel ECU Assembly 1.781,5.177 2.094,5.375 0.313,0.198 10 false E1 1.51,5.052 1.823,5.25 0.313,0.198 10 false 22 1.771,0.833 2.083,1.031 0.313,0.198 10 false IG 1.5,0.708 1.813,0.906 0.313,0.198 10 false 15 0.573,1.01 1.458,1.188 0.885,0.177 10 false ECU-IG NO.1 0.656,0.177 2.198,0.365 1.542,0.188 10 false from IG1 NO. 3 Relay 4.729,2.083 6.552,2.281 1.823,0.198 10 false Headlight Leveling Motor LH 4.74,5.052 6.646,5.281 1.906,0.229 10 false Headlight Leveling Motor RH 4.635,2.844 5.094,3.042 0.458,0.198 10 false A66 4.625,3.01 6.563,3.208 1.938,0.198 10 false Headlight Unit Assembly LH 4.688,5.823 5.146,6.021 0.458,0.198 10 false A69 4.698,5.979 6.427,6.156 1.729,0.177 10 false Headlight Unit Assembly RH 4.656,0.719 4.813,0.917 0.156,0.198 10 false 1 4.646,1.063 4.802,1.281 0.156,0.219 10 false 2 4.646,1.5 4.802,1.698 0.156,0.198 10 false 3 4.667,3.74 4.823,3.938 0.156,0.198 10 false 1 4.656,4.073 4.813,4.292 0.156,0.219 10 false 2 4.667,4.5 4.823,4.698 0.156,0.198 10 false 3 3.698,0.74 3.854,0.958 0.156,0.219 10 false 2 3.688,1.063 3.844,1.26 0.156,0.198 10 false 3 3.708,1.521 3.865,1.719 0.156,0.198 10 false 1 3.698,3.708 3.854,3.927 0.156,0.219 10 false 2 3.698,4.083 3.854,4.281 0.156,0.198 10 false 3 3.719,4.531 3.875,4.729 0.156,0.198 10 false 1 3.073,0.75 3.229,0.969 0.156,0.219 10 false 1 2.615,0.844 3.177,1.042 0.563,0.198 10 false SMBL 2.719,1.208 3.083,1.438 0.365,0.229 10 false LH+ 2.76,1.594 3.208,1.802 0.448,0.208 10 false LH- 3.073,1.073 3.292,1.313 0.219,0.24 10 false 30 3.063,1.51 3.281,1.75 0.219,0.24 10 false 27 2.583,3.854 3.198,4.052 0.615,0.198 10 false SMBR 3.083,3.74 3.24,3.938 0.156,0.198 10 false 2 2.667,4.24 3.281,4.438 0.615,0.198 10 false RH+ 3.083,4.073 3.333,4.271 0.25,0.198 10 false 11 2.688,4.615 3.302,4.813 0.615,0.198 10 false RH- 3.083,4.521 3.385,4.813 0.302,0.292 10 false 28 3.917,4.083 4.531,4.281 0.615,0.198 10 false RH T 3.906,0.75 4.521,0.948 0.615,0.198 10 false LHIG 3.906,1.51 4.521,1.708 0.615,0.198 10 false LH E 3.906,3.729 4.521,3.927 0.615,0.198 10 false RHIG 3.906,1.063 4.521,1.26 0.615,0.198 10 false LH T 3.906,4.531 4.521,4.729 0.615,0.198 10 false RH E

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After replacing the headlight swivel ECU, initialization of the ECU is necessary (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>INITIALIZATION).



PROCEDURE

1.CHECK FOR DTC

b.

Check for DTCs (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B2424 or B2425 output does not occur.




OK

NG

2.CHECK HARNESS AND CONNECTOR (HEADLIGHT SWIVEL ECU ASSEMBLY - BATTERY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (HEADLIGHT SWIVEL ECU ASSEMBLY - BATTERY AND BODY GROUND)
a.
U165787E01
0.054,0.036 0.238,0.218 0.184,0.182 10 *a 1.862,1.922 2.091,2.089 0.229,0.166 10 E1 1.603,1.545 1.84,1.955 false 1.613,0.517 1.985,0.686 0.372,0.170 10 E101 0.867,1.922 1.095,2.089 0.229,0.166 10 IG 0.884,1.905 0.56,1.537 false

Disconnect the headlight swivel ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E101-15 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E101-22 (E1) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Headlight Swivel ECU Assembly)


OK

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT SWIVEL ECU ASSEMBLY - HEADLIGHT UNIT ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT SWIVEL ECU ASSEMBLY - HEADLIGHT UNIT ASSEMBLY)
a.

Disconnect the E101 headlight swivel ECU connector.


b.

Disconnect the A66*1 or A69*2 headlight unit connector.

*1: for LH

*2: for RH



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH:
Tester Connection Condition Specified Condition
E101-1 (SMBL) - A66-2 (LHIG) Always Below 1 Ω
E101-30 (LH+) - A66-3 (LH T) Always Below 1 Ω
E101-27 (LH-) - A66-1 (LH E) Always Below 1 Ω
E101-1 (SMBL) - Body ground Always 10 kΩ or higher
E101-30 (LH+) - Body ground Always 10 kΩ or higher
E101-27 (LH-) - Body ground Always 10 kΩ or higher

for RH:
Tester Connection Condition Specified Condition
E101-2 (SMBR) - A69-2 (RHIG) Always Below 1 Ω
E101-11 (RH+) - A69-3 (RH T) Always Below 1 Ω
E101-28 (RH-) - A69-1 (RH E) Always Below 1 Ω
E101-2 (SMBR) - Body ground Always 10 kΩ or higher
E101-11 (RH+) - Body ground Always 10 kΩ or higher
E101-28 (RH-) - Body ground Always 10 kΩ or higher




OK

4.INSPECT HEADLIGHT UNIT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT HEADLIGHT UNIT ASSEMBLY
a.
E330445E02
1.708,3.146 2.146,2.365 2.146,2.365 2.323,2.365 true 1.417,3.25 1,4.042 1,4.042 0.823,4.042 true 1.969,3.292 2.385,4.083 2.385,4.083 2.552,4.083 true 0.958,0.24 1.146,0.448 0.188,0.208 10 false *a 0.958,2.344 1.146,2.552 0.188,0.208 10 false *b 2.354,2.458 2.917,2.625 0.563,0.167 10 false RHIG*B 2.365,2.281 2.927,2.448 0.563,0.167 10 false LHIG*A 0.281,4.146 0.823,4.313 0.542,0.167 10 false RH E*B 0.281,3.958 0.844,4.125 0.563,0.167 10 false LH E*A 2.583,4.167 3.125,4.333 0.542,0.167 10 false RH T*B 2.583,3.99 3.146,4.156 0.563,0.167 10 false LH T*A

Remove the headlight unit (See page Vehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for LED Headlight)>REMOVAL).


b.

Disconnect the headlight leveling motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH:
Tester Connection Condition Specified Condition
2 (LHIG) - 1 Always Below 1 Ω
3 (LH T) - 2
1 (LH E) - 3

for RH:
Tester Connection Condition Specified Condition
2 (RHIG) - 1 Always Below 1 Ω
3 (RH T) - 2
1 (RH E) - 3


Text in Illustration
*A for LH
*B for RH
*a Front view of wire harness connector
(to Headlight Leveling Motor)
*b Front view of wire harness connector



OK

5.CHECK HEADLIGHT LEVELING MOTOR

NG

5.CHECK HEADLIGHT LEVELING MOTOR
a.

Temporarily replace the headlight leveling motor with a new or normally functioning one (See page Vehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for LED Headlight)>REMOVAL).


b.

Check for DTCs (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B2424 or B2425 output does not occur.


Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

END (HEADLIGHT LEVELING MOTOR WAS DEFECTIVE)

B

C

REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY