Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT ASSEMBLY(for Halogen Headlight and LED Headlight) › 2015.08–2017.08
RM2660E _59 Vehicle Exterior _052855 LIGHTING (EXT) _0255822 HEADLIGHT ASSEMBLY(for Halogen Headlight and LED Headlight) A

LIGHTING (EXT)  HEADLIGHT ASSEMBLY(for Halogen Headlight and LED Headlight)  DISASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

Handle components indoors as much as possible to prevent foreign matter from entering and adhering to headlight assembly components.

·

Do not reuse parts which have reduced fastening ability due to thread damage.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

When installing components, make sure that the wire harness is not pinched or pulled.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 81194A 1.REMOVE HEADLIGHT PROTECTOR LH

a.
B560770

Remove the headlight protector LH.

NOTICE:

Do not reuse the headlight protector LH.



Hide 81139 2.REMOVE HEADLIGHT SOCKET COVER

a.
E333253E01
1.143,1.818 1.338,1.986 0.195,0.167 10 *a 1.232,0.678 1.232,1.807 false 1.16,4.259 1.355,4.426 0.195,0.167 10 *b 1.019,3.565 1.238,4.235 false

Turn the headlight socket cover counterclockwise until the matchmark is aligned with the unlock position mark to remove the headlight socket cover.

Text in Illustration
*a Matchmark
*b Unlock Position Mark


Hide 81110D 3.REMOVE NO. 2 HEADLIGHT BULB

a.
E333258

Disconnect the connector.


b.
E333259

Turn the No. 2 headlight bulb counterclockwise until the bulb stops.


c.

Remove the the No. 2 headlight bulb.

NOTICE:

Do not touch the glass part of the No. 2 headlight bulb.



Hide 81510C 4.REMOVE FRONT TURN SIGNAL LIGHT BULB

a.
E333248E01
2.332,1.994 2.564,2.164 0.232,0.170 10 *a 2.085,1.144 2.395,1.972 false 2.147,3.3 2.956,2.943 false 2.985,2.834 3.217,3.004 0.232,0.170 10 *b

Turn the front turn signal light socket counterclockwise until the matchmark is aligned with the unlock position mark to disconnect the front turn signal light socket.

Text in Illustration
*a Matchmark
*b Unlock Position Mark


b.
E333250

Remove the front turn signal light bulb from the front turn signal light socket.


Hide 81515B 5.REMOVE FRONT TURN SIGNAL LIGHT SOCKET

a.
E333251

Disconnect the connector and remove the front turn signal light socket.


Hide 81156A 6.REMOVE HEADLIGHT BRACKET LH (for Outside)

a.
E333243

Remove the 3 screws and headlight bracket LH.


Hide 81158 7.REMOVE HEADLIGHT BRACKET LH (for Inside)

a.
E333244

Remove the 3 screws and headlight bracket LH.


Hide 52134J 8.REMOVE FRONT BUMPER BAR REINFORCEMENT LH

a.
E333245

Remove the 2 screws.


b.
E333246

Detach the 2 guides and remove the front bumper reinforcement LH.


Hide 81171B 9.REMOVE HEADLIGHT LENS LH

NOTICE:
·

Perform work using clean rubber gloves.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.



a.
E333257

Remove the 2 screws and inner bracket.


b.
E333256

Remove the 2 screws and outer bracket.


c.
E333261E01
2.853,0.105 3.086,0.275 0.232,0.170 10 *a 1.781,0.541 2.803,0.213 false 1.411,2.97 0.545,3.147 false 0.35,3.063 0.582,3.233 0.232,0.170 10 *b

Turn the locking cap counterclockwise until the matchmark is aligned with the unlock position mark to remove the locking cap.

Text in Illustration
*a Matchmark
*b Unlock Position Mark


d.
E349687

Disconnect the connector.


e.

Remove the 7 screws.

B560793E01
1.598,0 1.879,0.211 0.281,0.211 12 *A 5.22,0 5.501,0.211 0.281,0.211 12 *B

Text in Illustration
*A Headlight Assembly LH Backside *B Headlight Assembly LH Surface


f.

Remove the headlight lens LH:

NOTICE:
·

Perform work using clean rubber gloves.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.



HINT:
·

The connection between the headlight lens LH and headlight housing is extremely tight. Therefore, make sure to use the following method of using a dryer to warm and soften the headlight lens gasket to separate the headlight lens LH and headlight housing.

·

With the headlight lens LH slightly lifted, cut the headlight lens gasket and separate the headlight lens LH.



i.

Using a dryer, warm the headlight lens gasket from the backside of the headlight assembly LH at the separation starting point of the headlight lens LH and headlight housing.

NOTICE:

If the headlight assembly LH is heated unevenly, it will deform or melt.


B560794E01
0.949,1.591 1.436,2.081 0.487,0.49 0.949,1.591 1.436,2.081 0.487,0.49 0.97,1.607 1.163,1.777 0.193,0.170 10 *a 1.538,0.185 1.830,0.510 0.292,0.325 12 *A 3.975,0.185 4.268,0.510 0.292,0.325 12 *B

Text in Illustration
*A Headlight Assembly LH Surface *B Headlight Assembly LH Backside
*a Separation Starting Point - -

HINT:
·

If the headlight lens LH cannot be lifted, even after heating, using a screwdriver, lift the headlight lens LH.

·

Tape the screwdriver tip before use.




ii.

Detach the 2 claws A and slightly lift the headlight lens LH.


iii.

Heat the headlight lens gasket starting from the backside of the headlight assembly LH and finishing at the area around claw B.


iv.

Detach the claw B and slightly lift the headlight lens LH.


v.

Heat the headlight lens gasket starting from the backside of the headlight assembly LH and finishing at the area around claw C.


vi.

Detach the 2 claws C and slightly lift the headlight lens LH.


vii.

Heat the headlight lens gasket starting from the backside of the headlight assembly LH and finishing at the area around claw D.


viii.

Detach the 2 claws D and remove the headlight lens LH.

B560791E01
0.771,1.635 1.083,1.833 0.313,0.198 10 false *a 2.75,0.417 3.063,0.615 0.313,0.198 10 false *b 4.49,0.438 4.802,0.635 0.313,0.198 10 false *c 6.167,1.635 6.479,1.833 0.313,0.198 10 false *d 5.875,2.115 6.188,2.313 0.313,0.198 10 false *d 4.625,3.333 4.938,3.531 0.313,0.198 10 false *c 2.667,3.26 2.979,3.458 0.313,0.198 10 false *a

Text in Illustration
*a Claw A *b Claw B
*c Claw C *d Claw D



Hide 81132B 10.REMOVE HEADLIGHT LENS GASKET

NOTICE:
·

Perform work using clean rubber gloves.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

The gasket must not be reused.



a.

Remove the headlight lens gasket from the headlight lens and headlight housing.

HINT:

Using a dryer, heat the headlight lens gasket. While softening the headlight lens gasket, remove it from the headlight lens LH and headlight housing.



Hide 81171A 11.REMOVE HEADLIGHT UNIT LH

NOTICE:
·

Perform work using clean rubber gloves.

·

Do not touch the headlight unit LH with bare hands.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.



a.

Using a vernier caliper, measure and record the protrusion amount of the horizontal and vertical aiming screw.

E349694E01
0.302,0.896 0.458,1.073 0.156,0.177 10 true *a 6.646,1.115 6.802,1.292 0.156,0.177 10 true *a

Text in Illustration
*a Protrusion Amount Measurement Area - -


b.
E349695

Disconnect the connector.


c.

Using a screwdriver, detach the 6 claws and remove the headlight unit LH.

E349696

Text in Illustration
V100155

Protective Tape - -


d.
E333271

Remove the leveling motor joint.

HINT:

Install the removed leveling motor joint to the headlight unit LH.



e.
E333272

Turn the aiming screw joint counterclockwise and remove it.

HINT:
·

Use the same procedure to remove the aiming screw joint on the other side.

·

Install the removed aiming screw joint to the headlight unit LH.




Hide 85662 12.REMOVE HEADLIGHT LEVELING MOTOR LH

a.
E333481

Disconnect the connector.


b.

Turn the headlight leveling motor LH counter clockwise and remove it.

E333277


Hide 85669 13.REMOVE HEADLIGHT LEVELING MOTOR BASE PACKING

a.

Remove the headlight leveling motor base packing from the headlight leveling motor LH.

NOTICE:

The packing must not be reused.