Home › Vehicle Exterior › LIGHTING (EXT) › AUTOMATIC HIGH BEAM MAIN SWITCH › from 2015.08
RM2660E _59 Vehicle Exterior _052855 LIGHTING (EXT) _0255824 AUTOMATIC HIGH BEAM MAIN SWITCH G

LIGHTING (EXT)  AUTOMATIC HIGH BEAM MAIN SWITCH  INSPECTION  


PROCEDURE

Hide 84153 1.INSPECT AUTO HIGH BEAM SWITCH

a.

except China:

Inspect the auto high beam switch.

i.
U165776E02
2.125,1.323 2.521,1.719 false 1.302,1.323 0.896,1.719 false 0.083,0.031 0.292,0.219 0.208,0.188 10 false *a 2.573,1.646 2.708,1.833 0.135,0.188 10 false E 0.646,1.656 0.906,1.844 0.26,0.188 10 false +B 1.594,0.177 1.927,0.354 0.333,0.177 10 false G22

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G22-4 (+B) - G22-1 (E) Auto high beam switch off 10 kΩ or higher
Auto high beam switch on Below 1 Ω


If the result is not as specified, replace the auto high beam switch.

Text in Illustration
*a Component without harness connected
(Auto High Beam Switch)



b.

for China:

Inspect the auto high beam switch.

i.
U165778E02
2.125,1.323 2.521,1.719 false 1.302,1.323 0.896,1.719 false 0.083,0.031 0.292,0.219 0.208,0.188 10 false *a 2.573,1.646 2.708,1.833 0.135,0.188 10 false E 0.646,1.656 0.906,1.844 0.26,0.188 10 false +B 1.583,0.167 1.917,0.344 0.333,0.177 10 false G25

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G25-4 (+B) - G25-1 (E) Auto high beam switch off 10 kΩ or higher
Auto high beam switch on Below 1 Ω


If the result is not as specified, replace the auto high beam switch.

Text in Illustration
*a Component without harness connected
(Auto High Beam Switch)



c.

except China:

Check the illumination.

i.
U165777E02
1.885,1.323 2.281,1.719 false 1.594,1.323 1.188,1.719 false 0.083,0.031 0.292,0.219 0.208,0.188 10 false *a 2.323,1.646 2.646,1.833 0.323,0.188 10 false ILL- 0.802,1.656 1.24,1.844 0.438,0.188 10 false ILL+ 1.625,0.208 1.958,0.385 0.333,0.177 10 false G22

Apply battery voltage to the connector and check the LED illumination conditions.

OK:
Measurement Condition Specified Condition
Battery positive (+) → G22-3 (ILL+)
Battery negative (-) → G22-2 (ILL-)
Illuminates


If the result is not as specified, replace the auto high beam switch.

Text in Illustration
*a Component without harness connected
(Auto High Beam Switch)



d.

for China:

Check the illumination.

i.
U165779E02
1.885,1.323 2.281,1.719 false 1.594,1.323 1.188,1.719 false 0.083,0.031 0.292,0.219 0.208,0.188 10 false *a 2.323,1.646 2.646,1.833 0.323,0.188 10 false ILL- 0.802,1.656 1.24,1.844 0.438,0.188 10 false ILL+ 1.625,0.198 1.958,0.375 0.333,0.177 10 false G25

Apply battery voltage to the connector and check the LED illumination conditions.

OK:
Measurement Condition Specified Condition
Battery positive (+) → G25-3 (ILL+)
Battery negative (-) → G25-2 (ILL-)
Illuminates


If the result is not as specified, replace the auto high beam switch.

Text in Illustration
*a Component without harness connected
(Auto High Beam Switch)