Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT BUMPER(for Standard) › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052857 EXTERIOR PANELS / TRIM _0255835 FRONT BUMPER(for Standard) A

EXTERIOR PANELS / TRIM  FRONT BUMPER(for Standard)  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (for HID Headlight)

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 53806 3.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

a.
B310791

Remove the 3 bolts and screw.


b.

Turn the clip indicated by the arrow in the illustration to remove the front fender splash shield sub-assembly LH.


Hide 53805 4.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

a.
B310792

Remove the 3 bolts and 2 screws.


b.

Turn the clip indicated by the arrow in the illustration to remove the front fender splash shield sub-assembly RH.


Hide 53292A 5.REMOVE UPPER RADIATOR SUPPORT SEAL

Hide 53111 6.REMOVE RADIATOR GRILLE ASSEMBLY

Hide 52119A 7.REMOVE FRONT BUMPER COVER

HINT:

For the front bumper cover with garnish, use the procedure described below.


a.

Put protective tape around the front bumper cover.

B302149E01
0.482,1.879 0.831,2.109 0.349,0.230 10 *1 0.657,1.94 1.379,1.493 false

Text in Illustration
*1 Protective Tape - -


b.

Using a T30 "TORX" socket, remove the 6 screws.

B313279E02
0.375,0.125 0.667,0.427 0.292,0.302 10 false *A 3.938,0.125 4.229,0.427 0.292,0.302 10 false *B

Text in Illustration
*A LH Side *B RH Side


c.

Remove the 3 clips, 4 screws and 4 bolts.


d.

Detach the 10 claws and remove the front bumper cover.

B302150


e.

w/ TOYOTA Parking Assist-sensor System or w/ Fog Light:

Disconnect the No. 4 engine room wire connector and remove the front bumper cover.


f.
B181927

w/ Headlight Cleaner System:

Disconnect the headlight cleaner hose and remove the front bumper cover.


Hide 52611 8.REMOVE FRONT BUMPER ENERGY ABSORBER

a.
B302151

Remove the front bumper energy absorber.


Hide 52021 9.REMOVE FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY

a.
B302152

Remove the 6 nuts and front bumper reinforcement sub-assembly.


Hide 52026B 10.REMOVE FRONT NO. 2 BUMPER EXTENSION SUB-ASSEMBLY LH

a.
B302153

Remove the 4 nuts and front No. 2 bumper extension sub-assembly LH.


Hide 52025B 11.REMOVE FRONT NO. 2 BUMPER EXTENSION SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 52116A 12.REMOVE FRONT BUMPER SIDE SUPPORT LH

a.
B313278

Remove the 2 screws.


b.

Detach the 3 clips and remove the front bumper side support LH.


Hide 52115A 13.REMOVE FRONT BUMPER SIDE SUPPORT RH

HINT:

Use the same procedure described for the LH side.


Hide 81150 14.REMOVE HEADLIGHT ASSEMBLY LH

Hide 81110 15.REMOVE HEADLIGHT ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 52521 16.REMOVE FRONT UPPER CENTER BUMPER RETAINER

a.
B302155

Remove the 3 bolts and front upper center bumper retainer.