Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › ROOF DRIP SIDE FINISH MOULDING
RM2660E _59 Vehicle Exterior _052857 EXTERIOR PANELS / TRIM _0255837 ROOF DRIP SIDE FINISH MOULDING A

EXTERIOR PANELS / TRIM  ROOF DRIP SIDE FINISH MOULDING  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedures for the RH side and LH side.

·

The procedures listed below are for the LH side.

·

When installing the clip, heat the vehicle body and clip using a heat light.

Standard Heating Temperature:
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Clip 20 to 30°C (68 to 86°F)




NOTICE:

Do not heat the vehicle body and clip excessively.


PROCEDURE

Hide 75564B 1.INSTALL NO. 2 ROOF DRIP SIDE FINISH MOULDING RETAINER (w/ Roof Carrier)

B181085

a.

Install the retainer with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 63185H 2.INSTALL ROOF RACK BRACKET

B181078

a.

w/o Roof Carrier:

Install the 4 brackets with the 8 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

w/ Roof Carrier:

Install the bracket with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 75561 3.INSTALL NO. 1 ROOF DRIP SIDE FINISH MOULDING CLIP

HINT:

Perform the following procedures when replacing the No. 1 roof drip side finish moulding clip.


NOTICE:

Remove the double-sided tape where the clips will be installed on the body and clean the body with a non-residue type solvent.


a.
B187426E01
1.338,0.72 1.987,1.057 0.649,0.336 10 Adhesive 0.608,0.084 2.416,0.410 1.809,0.326 10 2 to 3 mm Bead of Adhesive 0.57,0.168 0.398,0.168 false 0.398,0.168 0.398,1.279 false 0.398,1.279 0.881,1.687 false 2.064,0.824 2.371,0.824 false

Apply a 2 to 3 mm (0.0788 to 0.118 in.) bead of adhesive (3M DP-105 or equivalent) to a new No. 1 roof drip side finish moulding clip.

HINT:

Adhesive strength (tensile strength): 13.7 MPa (140 kgf/cm2, 1991 psi) or more when the temperature is 23°C (73°F).



b.

Apply primer to the body where the No. 1 roof drip side finish moulding clip will be installed.

NOTICE:

Do not let the primer dry.



c.
B181079E03
2.188,0.729 2.76,1.271 2.76,1.271 2.76,1.469 false 0.469,1.344 0.469,0.573 0.469,0.573 0.656,0.573 false 2.51,1.479 3.135,1.792 0.625,0.313 10 false Location 0.708,0.49 1.333,0.802 0.625,0.313 10 false Location

While using the position shown in the illustration as a reference, place the No. 1 roof drip side finish moulding clip onto the roof panel. Then position and install the clip after lightly pressing against it so that the adhesive adheres to the primer.


d.

Install the rear roof drip side finish moulding when 40 minutes or more have elapsed after pressing and installing the No. 1 roof drip side finish moulding clip.

HINT:
·

Initial hardening time: 40 minutes

·

Complete hardening time: 48 hours




Hide 75554A 4.INSTALL REAR ROOF DRIP SIDE FINISH MOULDING LH

B181083

a.

Attach the clip to install the moulding.


Hide 75556C 5.INSTALL CENTER ROOF DRIP SIDE FINISH MOULDING LH

B181082

HINT:

Use the same procedure to install the moulding on the other side.


a.

Install the moulding as shown in the illustration.


Hide 75552 6.INSTALL ROOF DRIP SIDE FINISH MOULDING LH

B181081

HINT:

Use the same procedure to install the moulding on the other side.


a.

Install the moulding as shown in the illustration.


Hide 75597 7.INSTALL ROOF DRIP SIDE FINISH MOULDING JOINT COVER LH

B181080

a.

w/o Roof Carrier:

Attach the claws and clips to install the 4 covers.


b.

w/ Roof Carrier:

Attach the claw and clip to install the cover.


Hide 8.INSTALL ROOF RACK ASSEMBLY (w/ Roof Rack)

a.

Install the roof rack assembly (See page Vehicle Exterior>EXTERIOR PANELS / TRIM>ROOF RACK>INSTALLATION).


Hide 9.INSTALL ROOF CARRIER ASSEMBLY LH (w/ Roof Carrier)

a.

Install the roof carrier assembly LH (See page Vehicle Exterior>EXTERIOR PANELS / TRIM>ROOF CARRIER>INSTALLATION).