Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › ROOF DRIP SIDE FINISH MOULDING
RM2660E _59 Vehicle Exterior _052857 EXTERIOR PANELS / TRIM _0255837 ROOF DRIP SIDE FINISH MOULDING A

EXTERIOR PANELS / TRIM  ROOF DRIP SIDE FINISH MOULDING  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedures for the RH side and LH side.

·

The procedures listed below are for the LH side.

·

When replacing a clip, heat the vehicle body and clip using a heat light.



Standard Heating Temperature:
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Clip 20 to 30°C (68 to 86°F)


NOTICE:

Do not heat the vehicle body and clip excessively.


PROCEDURE

Hide 1.REMOVE ROOF CARRIER ASSEMBLY LH (w/ Roof Carrier)

a.

Remove the roof carrier assembly LH (See page Vehicle Exterior>EXTERIOR PANELS / TRIM>ROOF CARRIER>REMOVAL).


Hide 2.REMOVE ROOF RACK ASSEMBLY (w/ Roof Rack)

a.

Remove the roof rack assembly (See page Vehicle Exterior>EXTERIOR PANELS / TRIM>ROOF RACK>REMOVAL).


Hide 75597 3.REMOVE ROOF DRIP SIDE FINISH MOULDING JOINT COVER LH

B181080E03
1.656,1.792 1.656,1.5 false 1.198,1.813 2.229,2.073 1.031,0.26 10 false Protective Tape

a.

Put protective tape around the cover.


b.

w/o Roof Carrier:

Detach the claw and clip and remove the 4 covers.


c.

w/ Roof Carrier:

Detach the claw and clip and remove the cover.


Hide 75552 4.REMOVE ROOF DRIP SIDE FINISH MOULDING LH

B181081E03
2.698,1.604 2.698,1.125 false 2.219,1.615 3.219,1.875 1,0.26 10 false Protective Tape

HINT:

Use the same procedure to remove the moulding on the other side.


a.

Put protective tape around the moulding.


b.

Remove the moulding.


Hide 75556C 5.REMOVE CENTER ROOF DRIP SIDE FINISH MOULDING LH

B181082E03
2.406,1.354 2.406,0.938 false 1.927,1.365 2.979,1.635 1.052,0.271 10 true Protective Tape

HINT:

Use the same procedure to remove the moulding on the other side.


a.

Put protective tape around the moulding.


b.

Remove the moulding.


Hide 75554A 6.REMOVE REAR ROOF DRIP SIDE FINISH MOULDING LH

B181083E03
2.229,1.729 2.229,1.49 false 1.76,1.771 2.833,2.104 1.073,0.333 10 true Protective Tape

a.

Put protective tape around the moulding.


b.

Using a moulding remover, detach the clip and remove the moulding.

NOTICE:
·

When removing the rear roof drip side finish moulding, be careful not to damage the No. 1 roof drip side finish moulding clip.

·

If the No. 1 roof drip side finish moulding clip is damaged or becomes detached from the vehicle, replace it with a new one.




Hide 75561 7.REMOVE NO. 1 ROOF DRIP SIDE FINISH MOULDING CLIP

B181079

HINT:

Perform the following procedures if replacing a No. 1 roof drip side finish moulding clip.


a.

Using a heat light, heat the clip and vehicle body.

NOTICE:

Do not heat the clip and vehicle body excessively.



b.

Remove the clip.


Hide 63185H 8.REMOVE ROOF RACK BRACKET

B181078

a.

w/o Roof Carrier:

Remove the 8 bolts and 4 brackets.


b.

w/ Roof Carrier:

Remove the 2 bolts and bracket.


Hide 75564B 9.REMOVE NO. 2 ROOF DRIP SIDE FINISH MOULDING RETAINER (w/ Roof Carrier)

B181085

a.

Remove the 2 bolts and retainer.