Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › SIDE STEP
RM2660E _59 Vehicle Exterior _052857 EXTERIOR PANELS / TRIM _0255849 SIDE STEP A

EXTERIOR PANELS / TRIM  SIDE STEP  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedures for the RH side and LH side.

·

The procedures listed below are for the LH side.

·

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).



PROCEDURE

Hide 51759A 1.INSTALL REAR SIDE DOOR STEP PLATE COVER LH

B180955

a.

Temporarily install the step plate cover with the 2 screws.

HINT:

Make sure the screws are loose so that the step plate moulding can be installed.



Hide 51775C 2.INSTALL NO. 1 SIDE DOOR STEP PLATE MOULDING

a.

Install the step plate moulding.

B183712

HINT:
B180950

Push in the step plate moulding until it in the position shown in the illustration.



b.

Tighten the installation screws of the step plate cover.


Hide 51774A 3.INSTALL FRONT SIDE DOOR STEP PLATE COVER LH

B180956

a.

Install the step plate cover with the 2 screws.


Hide 51792C 4.INSTALL REAR STEP PANEL LH

a.

Install a nose piece to an air riveter or hand riveter.


b.

Insert the mandrel part of a new rivet into the nose piece.


c.
B189901

Using the riveter, install the rear step panel shown in the illustration.

HINT:

If the rivet cannot be cut, pull it once and cut it.


NOTICE:
·
B171664E02
2.276,0.546 3.221,0.746 0.945,0.200 10 INCORRECT 2.276,2.385 2.992,2.585 0.717,0.200 10 CORRECT 0.246,1.484 0.770,1.687 0.524,0.203 10 Riveter 2.356,1.498 2.957,1.674 0.600,0.177 10 Mandrel 1.227,1.039 1.083,1.575 1.083,1.575 1.238,2.137 false 1.083,1.575 0.808,1.575 false 1.79,0.83 2.031,1.572 2.031,1.572 1.811,2.436 false 2.031,1.572 2.308,1.572 false

Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

·
B172390E02
2.325,0.536 3.200,0.713 0.876,0.177 10 INCORRECT 2.325,1.527 3.201,1.704 0.876,0.177 10 INCORRECT 2.434,2.73 3.175,2.907 0.741,0.177 10 CORRECT 1.043,0 1.542,0.152 0.500,0.152 10 Riveter 1.043,1.033 1.542,1.185 0.500,0.152 10 Riveter 0.72,0.066 1.023,0.066 false 0.818,1.11 1.018,1.11 false 1.043,2.324 1.542,2.477 0.500,0.152 10 Riveter 0.818,2.402 1.018,2.402 false

Confirm that the rivets are seated properly against the rear step panel.

·

Do not tilt the riveter when installing the rivet to the rear step panel.

·

Do not leave any space between the rivet head and rear step panel.

·
B172391E02
2.304,0.996 3.184,1.173 0.880,0.177 10 INCORRECT 2.408,2.434 3.140,2.611 0.732,0.177 10 CORRECT 0.978,0.515 1.499,0.685 0.521,0.171 10 Riveter 0.735,0.603 0.941,0.603 false 0.973,2.023 1.494,2.194 0.521,0.171 10 Riveter 0.731,2.111 0.937,2.111 false

Do not leave any space between the rear step panel and rear side door step plate cover. Firmly hold together the 2 items while installing the rivet.




Hide 51797A 5.INSTALL NO. 3 SIDE STEP BRACKET LH

B180952

a.

Install the side step bracket with the 2 bolts.


Hide 51796 6.INSTALL NO. 2 SIDE STEP BRACKET LH

B180953

a.

Install the side step bracket with the 2 bolts.


Hide 51793B 7.INSTALL NO. 1 SIDE STEP BRACKET LH

B180954

a.

Install the side step bracket with the 2 bolts.