Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › SIDE STEP(w/ Foot light)
RM2660E _59 Vehicle Exterior _052857 EXTERIOR PANELS / TRIM _0255860 SIDE STEP(w/ Foot light) A

EXTERIOR PANELS / TRIM  SIDE STEP(w/ Foot light)  DISASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 51793B 1.REMOVE NO. 1 SIDE STEP BRACKET LH

B192579

a.

Remove the 2 bolts and No. 1 side step bracket LH.


Hide 51796 2.REMOVE NO. 2 SIDE STEP BRACKET LH

B192580

a.

Detach the clamp.


b.

Remove the 2 bolts and No. 2 side step bracket LH.


Hide 51797A 3.REMOVE NO. 3 SIDE STEP BRACKET LH

B192581

a.

Remove the 2 bolts and No. 3 side step bracket LH.


Hide 82158B 4.REMOVE REAR STEP FLOOR WIRE LH

B192583

a.

Disconnect the connector.


b.

Detach the 4 clamps and remove the rear step floor wire LH.


Hide 81380D 5.REMOVE STEP LIGHT ASSEMBLY

B192587

a.

Remove the screw and step light assembly.


Hide 51772D 6.REMOVE STEP PLATE LH

a.

Detach the 16 clips and remove the step plate LH.

HINT:

Detach the clips from the backside of the step plate LH.


B192582


Hide 51782 7.REMOVE STEP PANEL LH

a.

Remove the 3 bolts and step panel.

B192584


Hide 51792 8.REMOVE NO. 2 STEP PLATE STAY

B192588E02
0.396,0.177 0.771,0.427 0.375,0.25 10 false 5 mm

a.

Put a 4 mm (0.157 in.) drill bit into a drill.


b.

Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill, as shown in the illustration.

HINT:

Tape the 4 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.



c.

Lightly press the drill against the rivet, drill off the flanges of the rivet, and remove the No. 2 step plate stay.

NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Do not pry the rivet with the drill, because this may cause damage to the installation holes of the rivet or the drill bit.



CAUTION:

Be careful of the drilled rivet as it may become hot.



d.

Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled area.


Hide 51788A 9.REMOVE STEP COVER REINFORCEMENT LH

B192590E02
0.448,1.052 0.885,1.313 0.438,0.26 10 false 5 mm

a.

Put a 4 mm (0.157 in.) drill bit into a drill.


b.

Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill, as shown in the illustration.

HINT:

Tape the 4 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.



c.

Lightly press the drill against the 2 rivets, drill off the flanges of the 2 rivets, and remove the step cover reinforcement LH.

NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Do not pry the rivet with the drill, because this may cause damage to the installation holes of the rivet or the drill bit.



CAUTION:

Be careful of the drilled rivet as it may become hot.



d.

Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled area.


Hide 51759A 10.REMOVE REAR SIDE DOOR STEP PLATE COVER LH

a.

Detach the 19 claws and remove the rear side door step plate cover LH.

B192586