Home › Vehicle Exterior › WINCH › WINCH UNIT
RM2660E _59 Vehicle Exterior _052858 WINCH _0255863 WINCH UNIT G

WINCH  WINCH UNIT  INSPECTION  


PROCEDURE

Hide 1.INSPECT WINCH WIRE

B192184

a.

Inspect the wire for the following damage: 1) areas where several strands are severed; 2) areas where the diameter is less than 7.5 mm (0.295 in.); 3) kinks; 4) corrosion; and 5) fraying.

If the wire is damaged, replace it with a new one.


Hide 38603A 2.INSPECT WINCH MOTOR ARMATURE SUB-ASSEMBLY

a.

Inspect the commutator for a shot circuit.

i.
B180515

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Commutator - Armature core Always 10 kΩ or higher


If the result is not as specified, replace the armature sub-assembly.



b.
B180516

Using a dial indicator, measure the circle runout of the commutator.

Standard runout:

0.05 mm (0.0020 in.) or less


Maximum runout:

0.2 mm (0.008 in.)


If the circle runout is more than the maximum, correct it with a lathe.


c.
B180517

Using a vernier caliper, measure the diameter of the commutator.

Standard diameter:

43 mm (1.69 in.)


Minimum diameter:

41 mm (1.61 in.)


If the diameter of the commutator is less than the minimum, replace the armature.


d.
B180518E01
1.793,0.956 3.297,0.956 false 1.707,0.882 3.297,0.882 false

Check that the undercut depth is clean and free of foreign particles. Then smooth off the edge and measure the undercut depth.

Standard undercut depth:

0.5 to 0.8 mm (0.020 to 0.031 in.)


Minimum undercut depth:

0.2 mm (0.008 in.)


If the undercut depth is less that the minimum, correct it with a hacksaw blade.


Hide 38601A 3.INSPECT WINCH MOTOR YOKE SUB-ASSEMBLY

a.

Inspect for an open circuit.

i.
B180519

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Lead wire - Field coil brush lead Always 10 kΩ or higher


If the result is not as specified, replace the winch motor yoke sub-assembly.



b.

Inspect the shunt coil for an open circuit.

i.
B180520

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Field coil brush lead - Field frame Always Below 1 Ω


If the result is not as specified, replace the winch motor yoke sub-assembly.



Hide 38613A 4.INSPECT WINCH MOTOR BRUSH

a.
B180521

Using a vernier caliper, measure the length of the brush.

Standard length:

22 mm (0.87 in.)


Minimum length:

15 mm (0.59 in.)


If the brush length is less than the minimum, replace the brush.


Hide 38613B 5.INSPECT WINCH MOTOR BRUSH SPRING

a.
A115032

Using a pull scale, measure the installed load of the brush spring.

Standard installed load:

16 to 20 N (1.6 to 2.0 kgf 3.6 to 4.4 lbf)


HINT:

Take the pull scale reading at the very instant the brush spring separates from the brush.



Hide 38604A 6.INSPECT WINCH MOTOR BRUSH HOLDER ASSEMBLY

a.

Inspect for an open circuit.

i.
B180523

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Positive (+) brush holder - Negative (-) brush holder Always Below 1 Ω


If the result is not specified, replace the brush holder assembly.



Hide 38603B 7.INSPECT NO. 1 WINCH MOTOR ARMATURE BEARING

a.
B180524

Turn each bearing by hand while applying inward force.

If the bearing sticks or resists, replace it.