Home › Vehicle Exterior › WINCH › WINCH UNIT
RM2660E _59 Vehicle Exterior _052858 WINCH _0255863 WINCH UNIT A

WINCH  WINCH UNIT  DISASSEMBLY  


PROCEDURE

Hide 38600A 1.REMOVE WINCH MOTOR ASSEMBLY

a.
B180487

Remove the 4 bolts and member.


b.
B180488

Remove the 8 bolts and winch base.


c.
B167951

Remove the 3 bolts and winch motor.


Hide 82296 2.REMOVE NO. 2 WINCH EARTH WIRE

a.
B188298

Remove the bolt and winch earth wire.


Hide 38360 3.REMOVE WINCH ROLLER BRACKET ASSEMBLY

a.
B188407

Remove the 2 nuts, 4 bolts and winch roller bracket.


Hide 38621B 4.REMOVE MAGNET SWITCH WINCH COVER

a.
B180508

Remove the 4 screws and cover.


Hide 38600A 5.REMOVE WINCH MOTOR MAGNET SWITCH ASSEMBLY

a.
B180509

Disconnect the connector.


b.

Remove the 2 nuts, 2 spring washers, 2 washers and wire harness.


c.
B180510

Remove the 4 bolts and magnet switch from the motor.


Hide 38618 6.REMOVE WINCH MOTOR COMMUTATOR END FRAME

a.
B180512

Remove the 2 bolts and commutator end frame.


Hide 38614A 7.REMOVE WINCH MOTOR O-RING

a.

Remove the O-ring.


Hide 38613A 8.REMOVE WINCH MOTOR BRUSH

a.
B180513

Using a screwdriver, pry the bush spring forward and pull the brush out of the holder.


b.
B180514

Remove the bolt and brush from the brush holder.

HINT:

Use the same procedures to remove the 3 remaining brushes.



Hide 38604A 9.REMOVE WINCH MOTOR BRUSH HOLDER ASSEMBLY

a.
B184478

Remove the brush holder in the direction of the arrow shown in the illustration.


Hide 38601A 10.REMOVE WINCH MOTOR YOKE SUB-ASSEMBLY

a.
B184477

Remove the yoke in the direction of the arrow shown in the illustration.


Hide 38603A 11.REMOVE WINCH MOTOR ARMATURE SUB-ASSEMBLY

a.
B180528

Remove the armature in the direction of the arrow shown in the illustration.


Hide 38603B 12.REMOVE NO. 1 WINCH MOTOR ARMATURE BEARING

a.
B180525E01
2.97,0.749 3.268,0.898 0.298,0.149 10 SST 2.715,0.832 2.959,0.832 false

Using SST, remove the bearing.

SST
09286-46011  


Hide 38603C 13.REMOVE NO. 2 WINCH MOTOR ARMATURE BEARING

a.
B180526E01
2.995,0.704 3.305,0.849 0.310,0.145 10 SST 2.781,0.785 2.991,0.785 false

Using SST, remove the bearing.

SST
09628-62011  


Hide 38613B 14.REMOVE WINCH MOTOR BRUSH SPRING

a.
U164033E01
2.76,0 3.302,0.361 0.542,0.361 10 Screwdriver A 1.74,2.596 2.660,2.759 0.920,0.163 10 Screwdriver B 1.262,2.416 1.575,2.687 1.575,2.687 1.726,2.687 false

Insert a screwdriver, labeled A, as shown in the illustration and pry the spring forward, then move the spring in the direction of the arrow shown in the illustration with a screwdriver, labeled B, to remove it from the holder.