Home › Vehicle Exterior › WINCH › WINCH UNIT
RM2660E _59 Vehicle Exterior _052858 WINCH _0255863 WINCH UNIT A

WINCH  WINCH UNIT  REASSEMBLY  


PROCEDURE

Hide 38613B 1.INSTALL WINCH MOTOR BRUSH SPRING

a.
B187368

Install the brush spring as shown in the illustration.


Hide 38603B 2.INSTALL NO. 1 WINCH MOTOR ARMATURE BEARING

a.
B180527E01
2.172,0.56 3.146,0.873 0.974,0.313 10 12 mm Socket Wrench 1.836,0.649 2.154,0.649 false

Using a 12 mm socket wrench and press, press in a new bearing.


Hide 38603C 3.INSTALL NO. 2 WINCH MOTOR ARMATURE BEARING

a.
B184649E01
2.216,0.537 3.150,0.865 0.934,0.328 10 19 mm Socket Wrench 1.861,0.634 2.221,0.634 false

Using a 19 mm socket wrench and press, press in a new bearing.


Hide 38603A 4.INSTALL WINCH MOTOR ARMATURE SUB-ASSEMBLY

a.
B184479

Apply high temperature grease to the inside of the end frame bushing.


b.

Install the armature to the end frame.


Hide 38601A 5.INSTALL WINCH MOTOR YOKE SUB-ASSEMBLY

a.
B180529

Align the alignment marks and install the yoke to the end frame.


Hide 38604A 6.INSTALL WINCH MOTOR BRUSH HOLDER ASSEMBLY

a.
B180530

Align the alignment marks and install the brush holder to the yoke.


Hide 38613A 7.INSTALL WINCH MOTOR BRUSH

a.
B180514

Install the brush with the bolt.

Torque:
3.4 N*m (35 kgf*cm, 30 in.*lbf)


b.
B180513

Using a screwdriver, pry the brush spring forward and insert the brush into the holder as shown in the illustration, then remove the screwdriver from the spring.

HINT:

Use the same procedures to install the 3 remaining brushes.



Hide 38614A 8.INSTALL WINCH MOTOR O-RING

a.

Install a new O-ring to the yoke.


Hide 38618 9.INSTALL WINCH MOTOR COMMUTATOR END FRAME

a.
B180512

Install the end frame with the 2 bolts.

Torque:
7.7 N*m (79 kgf*cm, 69 in.*lbf)


Hide 38600A 10.INSTALL WINCH MOTOR MAGNET SWITCH ASSEMBLY

a.
B180510

Install the switch to the motor with the 4 bolts.

Torque:
4.9 N*m (50 kgf*cm, 43 in.*lbf)


b.
B180509

Install the wire harness with the 2 washers, 2 spring washers and 2 nuts.

Torque:
9.3 N*m (95 kgf*cm, 82 in.*lbf)


c.

Connect the connector.


Hide 38621B 11.INSTALL MAGNET SWITCH WINCH COVER

a.
B180508

Install the cover with the 4 screws.

Torque:
1.5 N*m (15 kgf*cm, 13 in.*lbf)


Hide 38360 12.INSTALL WINCH ROLLER BRACKET ASSEMBLY

a.
U164099E01
0.302,0.641 0.436,0.807 0.134,0.165 10 A 1.22,1.468 1.350,1.631 0.130,0.163 10 B 1.218,1.243 1.352,1.408 0.134,0.165 10 A 0.304,0.886 0.435,1.049 0.130,0.163 10 B

Install the roller bracket with the 4 bolts and 2 nuts.

Torque:
for bolt A : 21.6 N*m (220 kgf*cm, 15 ft.*lbf)
for bolt B : 28.4 N*m (289 kgf*cm, 20 ft.*lbf)


Hide 82296 13.INSTALL NO. 2 WINCH EARTH WIRE

a.
B188298

Install the winch earth wire with the bolt.

Torque:
17.5 N*m (178 kgf*cm, 12 ft.*lbf)


Hide 38600A 14.INSTALL WINCH MOTOR ASSEMBLY

B167951

a.

Install the winch motor with the 3 bolts.

Torque:
15.7 N*m (160 kgf*cm, 11 ft.*lbf)


b.
B180488E01
1.361,0.34 1.490,0.506 0.130,0.165 10 A 2.067,0.343 2.195,0.504 0.128,0.161 10 B 0.807,0.34 0.937,0.505 0.130,0.165 10 A 2.666,0.343 2.794,0.504 0.128,0.161 10 B 1.363,1.608 1.491,1.768 0.128,0.161 10 B 2.659,1.608 2.787,1.768 0.128,0.161 10 B 2.037,1.608 2.165,1.768 0.128,0.161 10 B 0.806,1.608 0.934,1.768 0.128,0.161 10 B

Install the winch base with the 8 bolts.

Torque:
for bolt A : 32.3 N*m (329 kgf*cm, 23 ft.*lbf)
for bolt B : 58.8 N*m (599 kgf*cm, 43 ft.*lbf)


c.
B180487

Install the member with the 4 bolts.

Torque:
21.6 N*m (220 kgf*cm, 15 ft.*lbf)