Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (w/ Telematics Transceiver except G-BOOK) › from 2016.08
RM2660E _56 Audio / Visual / Telematics _052866 TELEMATICS _0283437 TELEMATICS SYSTEM(w/ Telematics Transceiver except G-BOOK) C

TELEMATICS  TELEMATICS SYSTEM(w/ Telematics Transceiver except G-BOOK)  B1570  Red LED Error  


DESCRIPTION

This DTC is stored when the telematics transceiver detects an open or short in the manual (SOS) switch indicator (red) circuit of the manual (SOS) switch.

The manual (SOS) switch indicator (red) illuminates for 10 seconds and turns off when the engine switch is turned on (IG).

If a malfunction in the telematics system is detected, the manual (SOS) switch indicator (red) will illuminate. However, the manual (SOS) switch indicator (red) may not illuminate when this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1570 Red LED Error Current for the manual (SOS) switch indicator (red) exceeds malfunction threshold for 20 seconds when the engine switch is on (IG).
·

Telematics transceiver

·

Map light assembly (manual (SOS) switch)

·

Harness or connector



WIRING DIAGRAM

E355988E07
1,2.302 3.75,2.5 2.75,0.198 10 false Map Light Assembly 0.979,2.135 1.292,2.333 0.313,0.198 10 false R7 1.427,1.74 4.177,1.938 2.75,0.198 10 false Manual (SOS) Switch 1.896,1 2.281,1.208 0.385,0.208 10 false RED 3.469,0.667 3.854,0.875 0.385,0.208 10 false IND1 3.396,1.083 3.844,1.302 0.448,0.219 10 false GND9 5.167,0.771 5.552,0.979 0.385,0.208 10 false IND1 4.906,1.938 6.49,2.208 1.583,0.271 10 false Telematics Transceiver 4.906,1.771 5.323,2 0.417,0.229 10 false P3 4.917,0.677 5.229,0.875 0.313,0.198 10 false 11 3.854,0.677 4.167,0.875 0.313,0.198 10 false 24 3.854,1.083 4.167,1.281 0.313,0.198 10 false 17

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (w/ Telematics Transceiver except G-BOOK)>REGISTRATION


HINT:

If DTC B1570 is stored, the manual (SOS) switch indicator (red) may not illuminate when another DTC is stored.


PROCEDURE

1.CHECK FOR DTC
a.

Turn the engine switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG) and wait for 20 seconds.


d.

Turn the GTS on.


e.

Check for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (w/ Telematics Transceiver except G-BOOK)>DTC CHECK / CLEAR

OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH) (RED INDICATOR)
2.INSPECT MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH) (RED INDICATOR)
a.
E262715C14
1.719,1.25 1.802,1.833 1.802,1.833 2.052,1.833 true 2.438,1.229 2.583,1.625 2.583,1.625 2.833,1.625 true 0.031,0.042 0.344,0.24 0.313,0.198 10 false *a 2.094,1.76 2.573,1.948 0.479,0.188 10 false IND1 2.885,1.542 3.365,1.729 0.479,0.188 10 false GND9
*a Component without harness connected
(Map Light Assembly (Manual (SOS) Switch))


Remove the map light assembly (manual (SOS) switch).

Click hereVehicle Interior>LIGHTING (INT)>ROOM LIGHT(for Front)>REMOVAL


b.

Connect 2 dry-cell batteries (1.5 V each) in series.


c.

Connect a positive (+) lead from the batteries to terminal 24 (IND1) and a negative (-) lead to terminal 17 (GND9) of the map light assembly (manual (SOS) switch) connector.


d.

Check if the manual (SOS) switch indicator (red) illuminates.

OK:

Manual (SOS) switch indicator (red) illuminates.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY (MANUAL(SOS) SWITCH) - TELEMATICS TRANSCEIVER AND BODY GROUND)

NG

REPLACE MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH)

3.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY (MANUAL(SOS) SWITCH) - TELEMATICS TRANSCEIVER AND BODY GROUND)
a.

Disconnect the R7 map light assembly (manual (SOS) switch) connector.


b.

Disconnect the P3 telematics transceiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P3-11 (IND1) - R7-24 (IND1) Always Below 1 Ω
P3-11 (IND1) or R7-24 (IND1) - Body ground Always 10 kΩ or higher
R7-17 (GND9) -Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.REPLACE TELEMATICS TRANSCEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT