These DTCs are stored when a malfunction occurs in the telephone antenna.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1573 | Short in Telephone Antenna Circuit | Telephone antenna assembly impedance (Ω) is lower than the malfunction threshold for 20 seconds when the engine switch is on (IG).
(Short circuit) |
·
Telematics transceiver ·
Telephone antenna assembly ·
No. 4 antenna cord sub-assembly ·
Harness or connector |
| B15CB | Telephone Antenna Disconnected | Telephone antenna assembly impedance (Ω) is higher than the malfunction threshold for 20 seconds when the engine switch is on (IG).
(Open circuit) |
·
Telematics transceiver ·
Telephone antenna assembly ·
No. 4 antenna cord sub-assembly ·
Harness or connector |
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and wait for 20 seconds.
Turn the GTS on.
Check for DTCs and check that no DTCs are output.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Remove the telephone antenna assembly.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA>REMOVAL
| *a | Component without harness connected
(Telephone Antenna Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4 - 4a | Always | 4 to 11 kΩ |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the antenna connector from the telephone antenna assembly.
Disconnect the antenna connector from the wire harness.
| *a | Front view of wire harness connector
(to Telephone Antenna Assembly) |
| *b | Front view of wire harness connector
(to Wire Harness) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-4 - B-1 | Always | Below 1 Ω |
| A-4 or B-1 - Body ground | Always | 10 kΩ or higher |
| A-4a - B-1a | Always | Below 1 Ω |
| A-4a or B-1a - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to No. 4 Antenna Cord Sub-assembly) |
| *b | Front view of wire harness connector
(to Telematics Transceiver) |
Disconnect the antenna connector from the No. 4 antenna cord sub-assembly.
Disconnect the antenna connector from the telematics transceiver.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C-1 - D-1 (ANT1) | Always | Below 1 Ω |
| C-1 or D-1 (ANT1) - Body ground | Always | 10 kΩ or higher |
| C-1a - D-1a | Always | Below 1 Ω |
| C-1a or D-1a - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telematics transceiver with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT