Home › Engine / Hybrid System › 1UR-FE (ENGINE MECHANICAL) › CYLINDER HEAD › from 2016.08
RM2660E _51 Engine / Hybrid System _052776 1UR-FE ENGINE MECHANICAL _0255041 CYLINDER HEAD A

1UR-FE ENGINE MECHANICAL  CYLINDER HEAD  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


a.

Using E7 and E8 "TORX" socket wrenches, install the stud bolts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

U163320E01
3.113,3.921 3.235,4.067 0.121,0.145 10 D 1.756,3.103 1.877,3.249 0.121,0.145 10 C 4.429,4.172 4.550,4.317 0.121,0.145 10 D 4.408,3.832 4.529,3.978 0.121,0.145 10 A 5.502,3.097 5.623,3.243 0.121,0.145 10 C 6.587,1.417 6.708,1.562 0.121,0.145 10 B 0.756,1.339 0.877,1.485 0.121,0.145 10 B 1.322,5.016 2.471,5.185 1.149,0.169 10 12 mm (0.472 in.) 1.38,5.669 2.004,6.009 0.624,0.339 10 52 mm (2.05 in.) 2.368,6.471 3.517,6.645 1.150,0.174 10 13 mm (0.512 in.) 3.003,5.022 4.152,5.192 1.149,0.170 10 24 mm (0.945 in.) 2.907,5.715 3.526,6.055 0.619,0.339 10 45 mm (1.77 in.) 4.597,5.021 5.744,5.189 1.147,0.169 10 20 mm (0.787 in.) 6.312,5.011 6.993,5.345 0.681,0.334 10 14 mm (0.551 in.) 4.585,5.74 5.189,6.072 0.604,0.332 10 35 mm (1.38 in.) 6.118,5.728 6.733,6.063 0.615,0.335 10 29 mm (1.14 in.) 0.778,6.49 1.919,6.661 1.141,0.170 10 12 mm (0.472 in.) 0.804,0.887 0.804,1.318 false 6.633,0.967 6.633,1.398 false 1.112,2.733 1.112,3.001 false 1.373,2.751 1.373,3.004 false 1.802,3.007 1.802,3.086 false 1.697,2.439 1.697,3.001 false 2.235,2.751 2.235,3.003 false 2.498,2.44 2.498,3 false 4.77,2.723 4.77,2.996 false 5.036,2.432 5.036,2.989 false 5.596,2.436 5.596,2.992 false 5.89,2.744 5.89,2.992 false 6.151,2.746 6.151,2.994 false 5.546,2.998 5.546,3.078 false 2.671,3.995 3.067,3.995 false 2.571,4.27 2.811,4.27 2.811,4.27 2.811,3.995 false 4.922,4.248 4.565,4.248 false 4.831,3.978 4.698,3.978 4.698,3.978 4.698,4.248 false 4.903,3.907 4.545,3.907 false 0.564,6.442 0.685,6.587 0.121,0.145 10 A 2.168,6.442 2.289,6.587 0.121,0.145 10 B 3.815,6.442 3.937,6.587 0.121,0.145 10 C 5.306,6.442 5.427,6.587 0.121,0.145 10 D 0.937,3.432 1.150,3.587 0.213,0.155 10 *e 4.645,3.432 4.852,3.587 0.207,0.155 10 *f 0.4,0.201 0.585,0.355 0.185,0.155 10 *a 4.064,0.201 4.249,0.355 0.185,0.155 10 *b 0.319,1.832 0.504,1.987 0.185,0.155 10 *c 4.011,1.832 4.196,1.987 0.185,0.155 10 *d 1.105,6.489 1.105,6.424 1.105,6.424 0.885,6.273 false 2.698,6.489 2.698,6.424 2.698,6.424 2.477,6.273 false 4.028,6.471 5.177,6.645 1.150,0.174 10 13 mm (0.512 in.) 4.358,6.489 4.358,6.424 4.358,6.424 4.137,6.273 false 5.482,6.471 6.631,6.645 1.150,0.174 10 13 mm (0.512 in.) 5.851,6.489 5.851,6.424 5.851,6.424 5.631,6.273 false 1.299,5.089 1.235,5.089 1.235,5.089 0.885,5.461 false 2.967,5.089 2.903,5.089 2.903,5.089 2.47,5.671 false 4.556,5.089 4.491,5.089 4.491,5.089 4.138,5.909 false 6.288,5.089 6.223,5.089 6.223,5.089 5.627,5.941 false

Text in Illustration
*a for Intake Side of Bank 2 *b for Intake Side of Bank 1
*c for Exhaust Side of Bank 2 *d for Exhaust Side of Bank 1
*e for Front Side of Bank 2 *f for Front Side of Bank 1


Hide 11117F 2.INSTALL NO. 2 STRAIGHT SCREW PLUG

a.

Using a 14 mm hexagon wrench, install 2 new gaskets and the 2 No. 2 straight screw plugs.

Torque:
85 N*m (867 kgf*cm, 63 ft.*lbf)


Hide 11117E 3.INSTALL NO. 1 STRAIGHT SCREW PLUG

a.

Using a 10 mm hexagon wrench, install 6 new gaskets and the 6 No. 1 straight screw plugs.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)


Hide 13734 4.INSTALL VALVE SPRING SEAT

a.

Install the valve spring seats to the cylinder head.


Hide 13711E 5.INSTALL VALVE STEM OIL SEAL

a.
A385831E01
0.76,0.677 0.958,0.344 0.958,0.344 1.115,0.344 false 2.625,0.667 2.823,0.333 2.823,0.333 2.979,0.333 false 1.177,0.271 1.49,0.469 0.313,0.198 10 false *1 3.031,0.26 3.344,0.458 0.313,0.198 10 false *2 0.594,1.698 0.906,1.896 0.313,0.198 10 false *A 2.625,1.677 2.938,1.875 0.313,0.198 10 false *B

Apply a light coat of engine oil to 2 new valve stem oil seals.

Text in Illustration
*A for Intake Side
*B for Exhaust Side
*1 Brown
*2 Gray

NOTICE:

Pay attention when installing the intake and exhaust valve stem oil seals. Installing the intake valve stem oil seal to the exhaust side or installing the exhaust valve stem oil seal to the intake side can cause installation problems later.


HINT:

The intake valve oil seals are brown and the exhaust valve oil seals are gray.



b.
A165065E03
0.159,1.658 0.480,1.801 0.321,0.144 10 SST 0.535,1.743 0.643,1.743 0.643,1.743 1.502,1.113 false 0.906,2.37 1.091,2.525 0.185,0.155 10 *a 2.4,2.37 2.585,2.525 0.185,0.155 10 *b

Using SST, push in the valve stem oil seals.

SST
09201-41020  

Text in Illustration
*a CORRECT
*b INCORRECT

NOTICE:

Failure to use SST will cause the seal to be damaged or improperly seated.



Hide 13711 6.INSTALL INTAKE VALVE

a.
A385832E01
2.677,1.552 2.99,1.75 0.313,0.198 10 false *a

Apply a sufficient coat of engine oil to the tip area of the intake valve as shown in the illustration.

Text in Illustration
*a 40 mm (1.57 in.) or more


b.
A366793E02
0.531,0.354 0.771,0.563 0.24,0.208 10 false *a 0.531,1.531 0.781,1.75 0.25,0.219 10 false *b

Install the intake valve, compression spring and valve spring retainer to the cylinder head.

Text in Illustration
*a Narrow
*b Wide

NOTICE:
·

Install the same parts in the same combination to their original locations.

·

Install the inner compression spring to the wide end of the cylinder head sub-assembly.




c.
A366791E01
2.917,0.323 3.01,0.323 false 0.438,0.656 0.563,0.656 0.563,0.656 0.667,0.844 true 0.094,0.573 0.448,0.771 0.354,0.198 10 false SST 3.063,0.229 3.417,0.427 0.354,0.198 10 true SST

Using SST, compress the compression spring and install the 2 valve spring retainer locks.

SST
09202-70020  (09202-01010, 09202-01020)
09202-00021  


d.
A366795

Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:
·

Do not damage the valve stem tip.

·

Be careful not to damage the retainer.




Hide 13715 7.INSTALL EXHAUST VALVE

a.
A385833E01
2.667,1.625 2.979,1.823 0.313,0.198 10 false *a

Apply a sufficient coat of engine oil to the tip area of the exhaust valve as shown in the illustration.

Text in Illustration
*a 40 mm (1.57 in.) or more


b.
A366794E02
0.708,0.344 0.948,0.573 0.24,0.229 10 false *a 0.708,1.51 0.948,1.75 0.24,0.24 10 false *b

Install the exhaust valve, compression spring and valve spring retainer to the cylinder head.

Text in Illustration
*a Narrow
*b Wide

NOTICE:
·

Install the same parts in the same combination to their original locations.

·

Install the inner compression spring to the wide end of the cylinder head sub-assembly.




c.
A366792E01
0.417,0.271 0.542,0.271 false 2.99,1.698 2.885,1.698 2.885,1.698 2.792,1.594 true 0.104,0.188 0.438,0.396 0.333,0.208 10 false SST 3.031,1.615 3.365,1.823 0.333,0.208 10 false SST

Using SST, compress the compression spring and install the 2 valve spring retainer locks.

SST
09202-70020  (09202-01010, 09202-01020)
09202-00021  


d.
A366796

Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:
·

Do not damage the valve stem tip.

·

Be careful not to damage the retainer.