Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (w/ Multi-display) › from 2016.08
RM2660E _56 Audio / Visual / Telematics _052828 AUDIO / VIDEO _0255488 AUDIO AND VISUAL SYSTEM(w/ Multi-display) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(w/ Multi-display)  Sound Signal Circuit between Radio Receiver and Stereo Jack Adapter  


DESCRIPTION

The No. 1 stereo jack adapter assembly sends the sound signal from an external device to the multi-media module receiver assembly through this circuit.

The sound signal that has been sent is amplified by the stereo component amplifier assembly or multi-media module receiver assembly, and then is sent to the speakers.

If there is an open or short in the circuit, sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly, multi-media module receiver assembly, DCM (telematics transceiver)* or speakers.

*: w/ Telematics Transceiver


WIRING DIAGRAM

E296658E14
0.792,0.854 1.406,1.052 0.615,0.198 10 false ADPG 0.854,1.49 1.469,1.688 0.615,0.198 10 false VAR+ 0.875,2.083 1.49,2.281 0.615,0.198 10 false VAL+ 0.979,2.719 1.594,2.917 0.615,0.198 10 false VA- 0.823,3.323 1.438,3.521 0.615,0.198 10 false AGND 1.333,0.74 1.51,0.938 0.177,0.198 10 false 9 1.323,1.365 1.5,1.563 0.177,0.198 10 false 6 1.344,1.969 1.521,2.167 0.177,0.198 10 false 7 1.354,2.583 1.531,2.781 0.177,0.198 10 false 8 1.375,3.188 1.552,3.385 0.177,0.198 10 false 11 0.427,3.698 0.677,3.875 0.25,0.177 10 false t1 0.427,3.885 2.083,4.24 1.656,0.354 10 false No. 1 Stereo Jack Adapter Assembly 3.583,3.448 4.781,3.667 1.198,0.219 10 false * 5.698,0.76 6.031,0.927 0.333,0.167 10 false 16 5.771,1.354 6.104,1.521 0.333,0.167 10 false 7 5.771,1.99 6.104,2.156 0.333,0.167 10 false 8 5.688,2.604 6.021,2.771 0.333,0.167 10 false 15 5.792,3.208 6.125,3.375 0.333,0.167 10 false 5 5.979,0.865 6.594,1.063 0.615,0.198 10 false ADPG 6.01,1.448 6.625,1.646 0.615,0.198 10 false VAR+ 6,2.104 6.615,2.302 0.615,0.198 10 false VAL+ 5.99,2.698 6.604,2.896 0.615,0.198 10 false VA- 5.979,3.313 6.594,3.51 0.615,0.198 10 false AGND 5.865,3.667 6.479,3.865 0.615,0.198 10 false F96 5.865,3.833 7.156,4.344 1.292,0.51 10 false Multi-media Module Receiver Assembly 0.25,4.417 1.271,4.646 1.021,0.229 10 false *: Shielded

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.

Disconnect the F96 multi-media module receiver assembly connector.


b.

Disconnect the t1 No. 1 stereo jack adapter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F96-16 (ADPG) - t1-9 (ADPG) Always Below 1 Ω
F96-7 (VAR+) - t1-6 (VAR+) Always Below 1 Ω
F96-8 (VAL+) - t1-7 (VAL+) Always Below 1 Ω
F96-15 (VA-) - t1-8 (VA-) Always Below 1 Ω
F96-5 (AGND) - t1-11 (AGND) Always Below 1 Ω
F96-16 (ADPG) or t1-9 (ADPG) - Body ground Always 10 kΩ or higher
F96-7 (VAR+) or t1-6 (VAR+) - Body ground Always 10 kΩ or higher
F96-8 (VAL+) or t1-7 (VAL+) - Body ground Always 10 kΩ or higher
F96-15 (VA-) or t1-8 (VA-) - Body ground Always 10 kΩ or higher
F96-5 (AGND) or t1-11 (AGND) - Body ground Always 10 kΩ or higher




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR