Home › Drivetrain › AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM › from 2016.08
RM2660E _52 Drivetrain _052807 AE80F AUTOMATIC TRANSMISSION / TRANSAXLE _0255308 AUTOMATIC TRANSMISSION SYSTEM J

AE80F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  TCM Power Source Circuit  


DESCRIPTION

When the engine switch is turned on (IG), the battery voltage is applied to the IGSW of the TCM. The output signal from the MREL terminal of the ECM causes a current to flow to the coil, closing the contacts of the EFI MAIN NO. 1 relay and supplying power to terminal +B of the TCM.

WIRING DIAGRAM

C343079E09
6.385,3.719 6.792,3.896 0.406,0.177 10 false A80 6.385,3.875 6.792,4.052 0.406,0.177 10 false TCM 6.177,2.802 6.583,2.979 0.406,0.177 10 false GND 6.177,2.375 6.656,2.552 0.479,0.177 10 false IGSW 6.177,0.833 6.583,1.01 0.406,0.177 10 false +B 5.885,0.729 6.156,0.906 0.271,0.177 10 false 10 5.896,2.281 6.167,2.458 0.271,0.177 10 false 21 4.948,2.406 5.219,2.583 0.271,0.177 10 false 1R 4.948,2.833 5.219,3.01 0.271,0.177 10 false 1S 5,2.188 5.271,2.365 0.271,0.177 10 false 8 5,2.635 5.271,2.813 0.271,0.177 10 false 4 3.844,2.531 4.906,2.708 1.063,0.177 10 false ENG-IG2 NO. 2 2.979,3.104 3.708,3.281 0.729,0.177 10 false IG2 MAIN 2.667,3.625 4.625,3.802 1.958,0.177 10 false No. 2 Integration Relay 2.198,2.531 2.948,2.708 0.75,0.177 10 false IG2 MAIN 2.979,1.563 3.635,1.917 0.656,0.354 10 false EFI MAIN NO. 1 1.969,0.979 3.125,1.167 1.156,0.188 10 false EFI MAIN NO. 1 5.979,2.708 6.25,2.885 0.271,0.177 10 false 1 1.521,2.833 1.792,3.01 0.271,0.177 10 false 1R 1.573,4.156 2.042,4.333 0.469,0.177 10 false IG1D 1.365,4.042 1.583,4.219 0.219,0.177 10 false 3 1.094,4.479 1.563,4.656 0.469,0.177 10 false E128 1.094,4.635 2.656,4.99 1.563,0.354 10 false Certification ECU (Smart Key ECU Assembly) 1.573,2.615 1.844,2.792 0.271,0.177 10 false 2 1.521,2.406 1.792,2.583 0.271,0.177 10 false 1X 1.573,2.188 1.844,2.365 0.271,0.177 10 false 1 1.521,1.292 1.792,1.469 0.271,0.177 10 false 1S 1.573,1.073 1.844,1.25 0.271,0.177 10 false 8 0.667,1.26 1.167,1.438 0.5,0.177 10 false MREL 1.188,1.156 1.688,1.333 0.5,0.177 10 false 6 0.573,1.635 1.073,1.813 0.5,0.177 10 false A38 0.573,1.802 1.073,1.979 0.5,0.177 10 false ECM 0.396,3.094 0.896,3.271 0.5,0.177 10 false P/I-B 0.573,4.021 1.188,4.198 0.615,0.177 10 false Battery 4.948,0.865 5.219,1.042 0.271,0.177 10 false 1S 4.958,0.646 5.229,0.823 0.271,0.177 10 false 11

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TCM - BODY GROUND)
a.
U165640E02
1.292,1.948 1.448,2.938 true 0.125,0.052 0.406,0.229 0.281,0.177 10 false *a 1.167,2.969 1.938,3.156 0.771,0.188 10 false 1 (GND) 0.854,0.167 1.208,0.344 0.354,0.177 10 false A80

Disconnect the TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A80-1 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Rear view of wire harness connector
(to TCM)



OK

2.CHECK HARNESS AND CONNECTOR (NO. 2 INTEGRATION RELAY - TCM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (NO. 2 INTEGRATION RELAY - TCM)
a.

Disconnect the No. 2 integration relay 1R and 1S connectors.


b.

Disconnect the A80 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1S-11 - A80-10 (+B) Always Below 1 Ω
1R-8 - A80-21 (IGSW) Always Below 1 Ω
1S-11 or A80-10 (+B) - Body ground Always 10 kΩ or higher
1R-8 or A80-21 (IGSW) - Body ground Always 10 kΩ or higher




OK

GO TO ECM POWER SOURCE CIRCUIT (ENGINE CONTROL SYSTEM / SFI SYSTEM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR