Home › Engine / Hybrid System › 1VD-FTV (FUEL) › FUEL PUMP › from 2016.08
RM2660E _51 Engine / Hybrid System _052783 1VD-FTV FUEL _0255117 FUEL PUMP A

1VD-FTV FUEL  FUEL PUMP  INSTALLATION  


PROCEDURE

Hide 77020A 1.INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

a.

Apply a light coat of gasoline or grease to a new gasket, and install it to the fuel tank.


b.
A176324C04
1.063,2.781 1.781,3.063 true 1.167,2.49 1.781,2.365 true 1.823,2.26 2.135,2.417 0.313,0.156 10 false *a 1.833,2.99 2.146,3.146 0.313,0.156 10 false *b
*a Protrusion
*b Groove
V100135

Front


Install the fuel suction with pump and gauge tube into the fuel tank.

NOTICE:

Be careful not to bend the arm of the fuel sender gauge.


HINT:

Align the protrusion of the fuel suction with pump and gauge tube with the groove of the fuel tank.



c.
A392973C01
0.792,0.771 0.979,0.927 0.188,0.156 10 true *a 1.448,0.969 1.635,1.125 0.188,0.156 10 true *a
*a Co-rotation Prevention Check Mark
V100135

Front


Apply a co-rotation prevention check mark to the fuel tank vent tube assembly.

HINT:

Perform this procedure when replacement of the fuel tank vent tube assembly is necessary.



d.
A392972C01
1.063,0.344 1.5,0.458 true 1.583,0.594 2.656,0.396 true 0.906,0.229 1.094,0.385 0.188,0.156 10 false *a 2.688,0.292 3,0.448 0.313,0.156 10 false *b
*a Rotational Start Point Mark (Fuel Tank Assembly Side)
*b Rotational Start Point Mark (Fuel Pump Gauge Retainer Side)
V100135

Front


Temporarily place the fuel pump gauge retainer by aligning the rotational start point mark of a new fuel pump gauge retainer with the rotational start point mark of the fuel tank assembly while pressing the fuel tank vent tube assembly into the fuel tank assembly.


e.
A393131C01
0.719,4.396 1.646,4.135 true 1.208,2.469 1.625,2.74 true 1.667,2.854 2.469,2.583 true 1.063,1.146 1.458,1.281 true 0.615,0.635 0.865,0.802 true 0.792,2.802 0.594,2.292 true 1.5,1.24 1.813,1.396 0.313,0.156 10 false *1 0.458,0.5 0.771,0.656 0.313,0.156 10 false *a 2.479,2.458 2.792,2.615 0.313,0.156 10 false *b 1.073,2.323 1.385,2.479 0.313,0.156 10 false *c 0.552,4.333 0.865,4.49 0.313,0.156 10 false *d 0.49,2.125 0.802,2.281 0.313,0.156 10 false *1
*1 Fuel Pump Gauge Retainer
*a SST (Claw Set)
*b Rib
*c Cutout
*d SST (Claw Set) Incorrect Installation Point (Rotational Start Point Mark of Fuel Pump Gauge Retainer)


Set 4 SSTs (claw sets) to the fuel pump gauge retainer and temporarily install.

SST
09808-14031  (09808-01080, 09808-01090, 09808-01100)

NOTICE:
·

Align the cutout of SST (claw set) to the rib of the fuel pump gauge retainer.

·

Do not place SST on the rotational start point mark of the fuel pump gauge retainer, otherwise SST (claw set) cannot be set correctly.




f.
A387296C03
2.333,1.313 2.51,1.104 2.51,1.104 2.698,1.104 false 1.146,0.74 1.344,0.74 1.344,0.74 1.75,1.052 false 1.115,2.063 1.313,2.063 1.313,2.063 1.563,1.833 false 2.74,1.021 3.052,1.177 0.313,0.156 10 false *1 0.958,0.667 1.271,0.823 0.313,0.156 10 false *a 0.948,1.979 1.26,2.135 0.313,0.156 10 false *b
*1 Fuel Pump Gauge Retainer
*a SST (Claw Set)
*b Hook
V100135

Press
V100136

SST (Bolt)


While firmly pressing the claw of SST into rib of the fuel pump gauge retainer, tighten the bolt.


g.
A392968C01
0.583,0.5 1.094,0.5 true 0.854,1.781 1.219,1.615 true 0.406,0.385 0.719,0.542 0.313,0.156 10 false *a 0.688,1.729 0.875,1.896 0.188,0.167 10 true *b
*a SST (Plate)
*b SST (Claw Set)
V100135

SST (Bolt)


Temporarily install SST (plate) to SST (claw set) with 4 SSTs (bolts).


h.
A392969C01
1.771,1.167 2.708,1.167 true 0.708,0.698 1.135,0.698 true 2.74,1.073 2.948,1.229 0.208,0.156 10 true *a 0.635,0.604 0.844,0.76 0.208,0.156 10 true *b
*a Center of Fuel Pump Gauge Retainer
*b SST (Plate)
V100135

Front


Adjust the position of SST (plate) so that the setting hole of SST (handle) aligns with the center of the fuel pump gauge retainer.


i.
A393430C01
0.844,3.792 0.74,3.354 true 2.26,3.177 1.875,3.385 true 2.531,3.583 1.719,4.021 true 1.333,1.323 0.469,1.063 true 1.531,0.365 1.615,0.688 true 0.635,3.167 0.948,3.323 0.313,0.156 10 false *1 1.417,0.177 1.729,0.333 0.313,0.156 10 false *a 2.281,3.063 2.594,3.219 0.313,0.156 10 false *b 0.292,0.948 0.604,1.104 0.313,0.156 10 false *c 2.552,3.438 2.865,3.594 0.313,0.156 10 false *d
*1 Fuel Pump Gauge Retainer
*a SST (Plate)
*b SST (Claw Set)
*c SST (Bolt)
*d Rib
V113147

Press


While firmly pressing the SST (claw set) into rib of the fuel pump gauge retainer, tighten SST (bolt).


j.
A392974C01
0.802,0.75 0.99,0.906 0.188,0.156 10 true *a 1.24,0.271 1.427,0.427 0.188,0.156 10 false *b 2.094,1.948 2.271,2.104 0.177,0.156 10 true *c 1.458,0.927 1.646,1.083 0.188,0.156 10 true *a
*a Co-rotation Prevention Check Mark
*b Tightening Start Position
*c One and Half Rotation Position
V100135

Front


While one person presses the fuel tank vent tube assembly into the fuel tank assembly, have another person firmly press the fuel pump gauge retainer into the threads of the fuel tank assembly and tighten approximately one and a half turns.

NOTICE:
·

Do not use any tools other than SST, such as a screwdriver, etc.

·

Do not use excessive force when pressing down on SST, as the fuel tank vent tube assembly will place excessive force on the pump gauge retainer and be difficult to remove, and parts may be damaged.

·

Do not use an impact wrench or turn the SST handle with excessive force, as parts may be damaged.

·

Do not rotate the fuel pump gauge retainer when the co-rotation prevention check mark is out of place.




k.
A392975C01
0.719,1.74 1.302,1.51 true 0.552,1.667 0.75,1.823 0.198,0.156 10 true *a 0.958,0.896 1.271,1.052 0.313,0.156 10 false *b 1.5,0.49 1.813,0.646 0.313,0.156 10 false *c 1.135,4.385 1.323,4.542 0.188,0.156 10 true *d 2.208,1.26 2.521,1.417 0.313,0.156 10 false *b 2.177,0.604 2.49,0.76 0.313,0.156 10 false *c
*a SST (Plate)
*b Person in Charge of Tightening
*c Person in Charge of Supporting
*d Approximately 180°
V100135

Front


While one person presses the fuel tank vent tube assembly into the fuel tank assembly, have another person slowly tighten approximately 180°.


l.

Check the tightening condition of the fuel pump gauge retainer.

i.
A392976C01
2.042,2.917 2.677,2.771 true 0.635,2.865 1.052,3.01 true 0.813,4.063 1.667,3.646 true 0.458,2.75 0.771,2.906 0.313,0.156 10 false *1 0.635,4.021 0.948,4.177 0.313,0.156 10 false *2 2.708,2.667 3.021,2.823 0.313,0.156 10 false *a 2.521,3.5 2.833,3.656 0.313,0.156 10 false *b 2.427,0.469 2.583,0.635 0.156,0.167 10 true A 2.156,0.969 2.313,1.135 0.156,0.167 10 true A 1.552,2.5 2.031,2.698 0.479,0.198 10 false A - A
*1 Fuel Pump Gauge Retainer
*2 Fuel Tank Assembly
*a Vernier Caliper
*b Measurement Height
V100136

Front
V113146

Measurement Position


Using a vernier caliper, measure the upper surface dimensions of the fuel tank assembly at the 3 positions as shown in the illustration.

Standard:

Measurement difference is within 3 mm.


NOTICE:

If the measurement difference is approximately 6 mm, the threads misaligned by 1 threads (6 mm) and the fuel pump gauge retainer must be installed again.




m.

Install SST (handle) to SST (plate).

SST
09808-14031  (09808-01010, 09808-01020)


n.
A392977C01
2.49,0.969 2.792,0.51 true 0.771,1.958 1.354,1.677 true 1.823,3.063 2.625,2.948 true 2.74,0.344 3.052,0.5 0.313,0.156 10 false *a 0.615,1.927 0.927,2.083 0.313,0.156 10 false *b 2.031,2.302 2.344,2.458 0.313,0.156 10 false *c 2.656,2.854 2.865,3.01 0.208,0.156 10 true *d 1.198,2.604 1.375,2.76 0.177,0.156 10 true *e 2.938,1.375 3.125,1.531 0.188,0.156 10 false *f 1.448,0.094 1.656,0.281 0.208,0.188 10 false *g 0.135,0.5 0.323,0.656 0.188,0.156 10 false *f 2.302,0.125 2.51,0.313 0.208,0.188 10 false *g
*a SST (Handle)
*b SST (Plate)
*c Tightening Complete Position
*d Rotational Start Point Mark of Fuel Pump Gauge Retainer
*e Rotational Start Point Mark of Fuel Tank Assembly
*f Person in Charge of Tightening
*g Person in Charge of Supporting
V100135

Tighten
V100136

Front


While one person presses the fuel tank vent tube assembly onto the fuel tank assembly, have another person use SST (handle) and slowly tighten the fuel pump gauge retainer until it reaches the tightening complete position.


Hide 77100U 2.INSTALL FUEL TANK SUB-ASSEMBLY