Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › 2016.08–2017.08
RM2660E _51 Engine / Hybrid System _052774 1GR-FE ENGINE CONTROL _0255001 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0136  Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2)  P0137  Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2)  P0138  Oxygen Sensor Circuit High Voltage (Bank 1 Sensor 2)  P0156  Oxygen Sensor Circuit Malfunction (Bank 2 Sensor 2)  P0157  Oxygen Sensor Circuit Low Voltage (Bank 2 Sensor 2)  P0158  Oxygen Sensor Circuit High Voltage (Bank 2 Sensor 2)  


DESCRIPTION

HINT:

Sensor 2 refers to the sensor mounted behind the three-way catalytic converter and located far from the engine assembly.


A three-way catalyst converter is used in order to convert the carbon monoxide, hydrocarbons and nitrogen oxide into less harmful substances. To allow the three-way catalytic converter to function effectively, it is necessary to keep the air fuel ratio of the engine near the stoichiometric air fuel ratio. For the purpose of helping the ECM to deliver accurate air fuel ratio control, a heated oxygen sensor is used.

The heated oxygen sensor is located behind the three-way catalytic converter, and detects the oxygen concentration in the exhaust gas. Since the sensor is integrated with the heater that heats the sensing portion, it is possible to detect the oxygen concentration even when the intake air volume is low (the exhaust gas temperature is low).

When the air fuel ratio becomes lean, the oxygen concentration in the exhaust gas is rich. The heated oxygen sensor informs the ECM that the post-three way catalytic converter air fuel ratio is lean (low voltage, i.e. below 0.45 V).

Conversely, when the air fuel ratio is richer than the stoichiometric air fuel level, the oxygen concentration in the exhaust gas becomes lean. The heated oxygen sensor informs the ECM that the post-three way catalytic converter air fuel ratio is rich (high voltage, i.e. higher than 0.45 V). The heated oxygen sensor has the property of changing its output voltage drastically when the air fuel ratio is close to the stoichiometric level.

The ECM uses the supplementary information from the heated oxygen sensor to determine whether the air fuel ratio after the three-way catalytic converter is rich or lean, and adjusts the fuel injection time accordingly. Thus, if the heated oxygen sensor is working improperly due to internal malfunctions, the ECM is unable to compensate for deviations in the primary air fuel ratio control.

A208686E01
2.634,2.044 3.123,2.044 false 2.549,1.815 3.123,1.815 false 2.656,1.582 3.123,1.582 false 3.325,0.559 3.980,0.775 0.655,0.216 10 Housing 3.325,0.898 4.576,1.253 1.251,0.355 10 Solid Electrolyte (Zirconia Element) 3.157,1.496 4.408,1.682 1.251,0.186 10 Platinum Electrode 3.157,1.748 3.714,1.934 0.557,0.186 10 Heater 3.157,1.982 4.390,2.168 1.233,0.186 10 Coating (Ceramic) 1.044,2.219 1.24,2.219 false 1.294,2.157 1.748,2.343 0.455,0.186 10 Cover 1.777,2.472 2.621,2.658 0.844,0.186 10 Exhaust Gas 1.676,0 2.529,0.186 0.853,0.186 10 Atmosphere 3.955,0.21 4.956,0.396 1.001,0.186 10 Output Voltage 5.17,0.229 6.634,0.415 1.464,0.186 10 Ideal Air Fuel Mixture 4.723,2.246 6.818,2.392 2.096,0.146 10 Richer - Air Fuel Ratio - Leaner 2.689,1.451 3.23,0.965 3.23,0.965 3.305,0.965 false 3.072,0.62 3.291,0.62 false

DTC No. DTC Detection Condition Trouble Area
P0136
P0156
·

Abnormal voltage output:

During active air fuel ratio control, conditions (a) and (b) are met for a certain period of time (2 trip detection logic):

(a)

The heated oxygen sensor voltage does not decrease to below 0.21 V.

(b)

The heated oxygen sensor voltage does not increase to higher than 0.66 V.



·

Open or short in heated oxygen sensor (bank 1, 2 sensor 2) circuit

·

Heated oxygen sensor (bank 1, 2 sensor 2)

·

Heated oxygen sensor heater (bank 1, 2 sensor 2)

·

Air fuel ratio sensor (bank 1, 2 sensor 1)

·

Gas leak from exhaust system


P0137
P0157
·

Low voltage (open):

During active air fuel ratio control, conditions (a) and (b) are met for a certain period of time (2 trip detection logic):

(a)

The heated oxygen sensor voltage output is below 0.21 V.

(b)

The target air fuel ratio is rich.



·

Open in heated oxygen sensor (bank 1, 2 sensor 2) circuit

·

Heated oxygen sensor (bank 1, 2 sensor 2)

·

Heated oxygen sensor heater (bank 1, 2 sensor 2)

·

Gas leak from exhaust system


P0138
P0158
·

High voltage (short):

During active air fuel ratio control, conditions (a) and (b) are met for a certain period of time (2 trip detection logic):

(a)

The heated oxygen sensor voltage output is 0.66 V or higher.

(b)

The target air fuel ratio is lean.



·

Short in heated oxygen sensor (bank 1, 2 sensor 2) circuit

·

Heated oxygen sensor (bank 1, 2 sensor 2)

·

Air fuel ratio sensor (bank 1, 2 sensor 1)

·

ECM



MONITOR DESCRIPTION

Active Air-fuel Ratio Control

The ECM usually performs air-fuel ratio feedback control so that the air fuel ratio sensor output indicates a near stoichiometric air-fuel ratio. This vehicle includes active air-fuel ratio control in addition to regular air-fuel ratio control. The ECM performs active air-fuel ratio control to detect any deterioration in the Three-way Catalytic Converter (TWC) and heated oxygen sensor malfunctions (refer to the diagram below).

Active air-fuel ratio control is performed for approximately 15 to 20 seconds while driving with a warm engine. During active air-fuel ratio control, the air-fuel ratio is forcibly regulated to become lean or rich by the ECM. If the ECM detects a malfunction, a DTC is stored.


Abnormal Voltage Output of Heated Oxygen Sensor (DTC P0136 and P0156)

While the ECM is performing active air-fuel ratio control, the air-fuel ratio is forcibly regulated to become rich or lean. If the sensor is not functioning properly, the voltage output variation is small. For example, when the heated oxygen sensor voltage does not decrease to below 0.21 V and does not increase to higher than 0.66 V during active air-fuel ratio control, the ECM determines that the sensor voltage output is abnormal and stores DTC P0136 or P0156.

A115540E95
3.281,1.646 3.073,1.365 false 3.313,1.844 3.167,2.135 false 0.031,0.042 3.521,0.25 3.49,0.208 10 false HEATED OXYGEN SENSOR CIRCUIT MALFUNCTION 0.208,0.865 2.021,1.052 1.813,0.188 10 false Active Air-fuel Ratio Control 0.208,2.021 2.188,2.188 1.979,0.167 10 false Heated Oxygen Sensor Voltage 2.448,0.854 2.698,1.052 0.25,0.198 10 false Off 2.594,1.26 3.083,1.458 0.49,0.198 10 false Normal 2.188,1.625 2.688,1.823 0.5,0.198 10 false 0.66 V 2.188,2.396 2.698,2.594 0.51,0.198 10 false 0.21 V 2.521,2.052 3.219,2.25 0.698,0.198 10 false Abnormal 4.625,0.115 5.792,0.313 1.167,0.198 10 false 15 to 20 seconds 4.219,0.771 4.896,0.969 0.677,0.198 10 false Operating 0.031,0.479 2.813,0.656 2.781,0.177 10 false (P0136 and P0156: ABNORMAL VOLTAGE)


Open or Short in Heated Oxygen Sensor Circuit (DTC P0137 and P0157 or P0138 and P0158)

During active air-fuel ratio control, the ECM calculates the Oxygen Storage Capacity (OSC)* of the Three-way Catalytic Converter (TWC) by forcibly regulating the air-fuel ratio to become rich or lean. If the heated oxygen sensor has an open or short, or the voltage output of the sensor decreases significantly, the Oxygen Storage Capacity (OSC) is indicated as having an extraordinarily high value. Even if the ECM attempts to continue regulating the air-fuel ratio to become rich or lean, the heated oxygen sensor output does not change.

While performing active air-fuel ratio control, when the target air-fuel ratio is rich and the heated oxygen sensor voltage output is 0.21 V or less (lean), the ECM interprets this as an abnormally low sensor output voltage and stores DTC P0137 or P0157. When the target air-fuel ratio is lean and the voltage output is 0.66 V or more (rich) during active air-fuel ratio control, the ECM determines that the sensor voltage output is abnormally high and stores DTC P0138 or P0158.

*: The Three-way Catalytic Converter (TWC) has the capability to store oxygen. The Oxygen Storage Capacity (OSC) and the emissions purification capacity of the Three-way Catalytic Converter (TWC) are mutually related. The ECM determines whether the catalyst has deteriorated based on the calculated Oxygen Storage Capacity (OSC) value (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P0420).

A115541E64
4.646,2.052 4.333,1.927 true 5.969,6.25 6.156,6.031 false 5.99,2.729 6.177,2.396 false 6.021,3.5 6.208,3.708 false 5.104,2.406 5.229,1.792 true 0.063,0.094 3.573,0.323 3.51,0.229 10 false HEATED OXYGEN SENSOR CIRCUIT LOW VOLTAGE 0.073,0.479 1.844,0.688 1.771,0.208 10 false (P0137 and P0157: OPEN) 1.104,1.76 3.063,1.958 1.958,0.198 10 false Active Air-fuel Ratio Control 1,3.052 3.031,3.25 2.031,0.198 10 false Heated Oxygen Sensor Voltage 1.094,2.156 2.563,2.354 1.469,0.198 10 false Target Air-fuel Ratio 1.104,5.229 3.063,5.427 1.958,0.198 10 false Active Air-fuel Ratio Control 1,6.552 3.031,6.75 2.031,0.198 10 false Heated Oxygen Sensor Voltage 1.104,5.813 2.573,6.01 1.469,0.198 10 false Target Air-fuel Ratio 2.542,2.083 3.448,2.552 0.906,0.469 10 false Stoichiometric Air-fuel Ratio 3.229,1.76 3.49,1.958 0.26,0.198 10 false Off 2.99,3.229 3.448,3.427 0.458,0.198 10 false 0.21 V 0.104,4.135 3.646,4.344 3.542,0.208 10 false HEATED OXYGEN SENSOR CIRCUIT HIGH VOLTAGE 0.104,4.563 1.948,4.771 1.844,0.208 10 false (P0138 and P0158: SHORT) 2.521,5.74 3.531,6.208 1.01,0.469 10 false Stoichiometric Air-fuel Ratio 3.229,5.271 3.49,5.469 0.26,0.198 10 false Off 3.01,6.427 3.552,6.625 0.542,0.198 10 false 0.66 V 4.625,0.656 5.927,0.854 1.302,0.198 10 false 15 to 20 seconds 4.51,1.667 5.271,1.865 0.76,0.198 10 false Operating 4.531,4.719 5.292,4.917 0.76,0.198 10 false Operating 4.531,5.365 4.927,5.563 0.396,0.198 10 false Lean 3.865,1.844 4.427,2.042 0.563,0.198 10 false Normal 6.208,5.938 6.948,6.135 0.74,0.198 10 false Abnormal 5.271,1.688 6.01,1.885 0.74,0.198 10 false Abnormal 6.24,3.656 6.979,3.854 0.74,0.198 10 false Abnormal 6.219,2.302 6.781,2.5 0.563,0.198 10 false Normal 4.771,2.438 5.135,2.635 0.365,0.198 10 false Rich


WIRING DIAGRAM

for LHD:
A344680E10
1.365,1.74 2.458,2.229 1.094,0.49 10 false Integration Relay 3.594,2.01 4.958,2.5 1.365,0.49 10 false Heated Oxygen Sensor (for Bank 1) 3.583,4.656 4.958,5.313 1.375,0.656 10 false Heated Oxygen Sensor (for Bank 2) 6.177,6.427 6.844,6.667 0.667,0.24 10 false ECM 0.875,5.385 2.104,5.583 1.229,0.198 10 false Battery 0.688,3.427 1.917,3.625 1.229,0.198 10 false P/I-B 0.708,0.813 1.365,1.156 0.656,0.344 10 false EFI MAIN NO. 1 1.292,1.406 2.521,1.604 1.229,0.198 10 false EFI MAIN NO. 1 2.042,0.802 3.271,1 1.229,0.198 10 false EFI NO. 2 4.479,1.042 5.094,1.24 0.615,0.198 10 false OX1B 4.479,0.583 5.094,0.781 0.615,0.198 10 false HT1B 4.625,1.458 5.281,1.646 0.656,0.188 10 false E2 5.833,0.583 6.448,0.781 0.615,0.198 10 false HT1B 5.833,1.042 6.448,1.24 0.615,0.198 10 false OX1B 5.833,1.458 6.448,1.656 0.615,0.198 10 false EX1B 5.833,3.229 6.448,3.427 0.615,0.198 10 false HT2B 5.844,3.677 6.458,3.875 0.615,0.198 10 false OX2B 5.833,4.094 6.448,4.292 0.615,0.198 10 false EX2B 5.833,5.396 6.448,5.594 0.615,0.198 10 false MREL 4.479,3.219 5.094,3.417 0.615,0.198 10 false HT2B 4.479,3.677 5.094,3.875 0.615,0.198 10 false OX2B 4.604,4.094 5.219,4.292 0.615,0.198 10 false E2 5.5,0.667 5.958,0.865 0.458,0.198 10 false C45 5.479,3.313 5.938,3.51 0.458,0.198 10 false C45 5.5,5.365 5.958,5.563 0.458,0.198 10 false A38 0.49,1.521 0.948,1.719 0.458,0.198 10 false 1X 2.719,0.677 3.177,0.875 0.458,0.198 10 false 1S 2.677,1.531 3.135,1.729 0.458,0.198 10 false 1S 5.531,0.49 5.99,0.688 0.458,0.198 10 false 45 5.5,0.948 5.958,1.146 0.458,0.198 10 false 114 5.49,1.396 5.99,1.594 0.5,0.198 10 false 115 5.531,3.156 5.99,3.354 0.458,0.198 10 false 44 5.49,3.594 5.948,3.792 0.458,0.198 10 false 112 5.49,4.01 5.948,4.208 0.458,0.198 10 false 113 5.521,5.208 5.979,5.406 0.458,0.198 10 false 34 3.854,3.229 4.313,3.427 0.458,0.198 10 false +B 3.854,0.583 4.313,0.781 0.458,0.198 10 false +B 4.917,1.042 5.073,1.24 0.156,0.198 10 false 3 4.917,1.448 5.073,1.646 0.156,0.198 10 false 4 4.917,0.583 5.073,0.781 0.156,0.198 10 false 1 3.667,0.583 3.823,0.781 0.156,0.198 10 false 2 3.656,3.229 3.813,3.427 0.156,0.198 10 false 2 4.917,3.219 5.073,3.417 0.156,0.198 10 false 1 4.917,3.677 5.073,3.875 0.156,0.198 10 false 3 4.917,4.094 5.073,4.292 0.156,0.198 10 false 4 2.75,0.5 2.906,0.698 0.156,0.198 10 false 1 2.802,1.323 2.958,1.521 0.156,0.198 10 false 8 0.49,1.323 0.646,1.521 0.156,0.198 10 false 1 5.156,1.396 5.313,1.594 0.156,0.198 10 false * 5.115,4.021 5.271,4.219 0.156,0.198 10 false * 1,1.521 1.458,1.719 0.458,0.198 10 false 1S 0.958,1.333 1.281,1.5 0.323,0.167 10 false 4 5.49,1.125 5.948,1.323 0.458,0.198 10 false C45 5.479,1.563 5.938,1.76 0.458,0.198 10 false C45 5.49,3.76 5.948,3.958 0.458,0.198 10 false C45 5.479,4.177 5.938,4.375 0.458,0.198 10 false C45 3.604,1.854 4.063,2.052 0.458,0.198 10 false C20 3.594,4.479 4.052,4.677 0.458,0.198 10 false C21 3.646,5.896 4.74,6.083 1.094,0.188 10 false *: Shielded


for RHD:
A344680E06
5.827,0.582 6.219,0.738 0.392,0.156 10 HT1B 5.827,3.202 6.219,3.358 0.392,0.156 10 HT2B 4.447,3.202 4.839,3.358 0.392,0.156 10 HT2B 5.481,0.662 5.762,0.817 0.281,0.156 10 C46 5.481,1.119 5.762,1.275 0.281,0.156 10 C46 5.481,1.544 5.762,1.700 0.281,0.156 10 C46 5.481,3.295 5.762,3.451 0.281,0.156 10 C46 5.481,3.753 5.762,3.909 0.281,0.156 10 C46 5.481,4.172 5.762,4.328 0.281,0.156 10 C46 5.493,5.365 5.773,5.521 0.281,0.156 10 A52 5.831,1.025 6.237,1.181 0.406,0.156 10 OX1B 4.446,1.025 4.852,1.181 0.406,0.156 10 OX1B 5.831,3.659 6.237,3.815 0.406,0.156 10 OX2B 4.444,3.659 4.850,3.815 0.406,0.156 10 OX2B 5.831,1.444 6.223,1.600 0.392,0.156 10 EX1B 5.833,4.066 6.225,4.222 0.392,0.156 10 EX2B 5.841,5.285 6.261,5.441 0.420,0.156 10 MREL 6.131,6.397 6.478,6.553 0.347,0.156 10 ECM 5.533,0.484 5.762,0.656 0.229,0.171 10 45 5.484,0.94 5.796,1.150 0.312,0.211 10 114 5.484,1.36 5.796,1.571 0.312,0.211 10 115 5.533,3.132 5.730,3.288 0.198,0.156 10 44 5.533,5.185 5.730,5.341 0.198,0.156 10 34 5.497,3.585 5.774,3.744 0.277,0.159 10 112 5.497,3.997 5.774,4.156 0.277,0.159 10 113 3.698,1.82 4.058,1.998 0.360,0.178 10 C20 3.698,1.974 4.925,2.306 1.227,0.332 10 Heated Oxygen Sensor (for Bank 1) 3.686,4.446 3.981,4.602 0.295,0.156 10 C21 3.686,4.607 4.924,4.940 1.239,0.333 10 Heated Oxygen Sensor (for Bank 2) 4.898,0.568 5.012,0.725 0.114,0.156 10 1 3.673,0.568 3.787,0.724 0.114,0.156 10 2 4.898,1.025 5.024,1.176 0.126,0.151 10 3 4.898,1.46 5.026,1.616 0.128,0.156 10 4 4.903,3.202 5.018,3.359 0.114,0.156 10 1 3.659,3.202 3.773,3.358 0.114,0.156 10 2 4.903,3.659 5.029,3.810 0.126,0.151 10 3 4.903,4.085 5.032,4.241 0.128,0.156 10 4 3.852,0.568 4.049,0.724 0.198,0.156 10 +B 3.838,3.202 4.035,3.358 0.198,0.156 10 +B 4.452,0.568 4.844,0.724 0.392,0.156 10 HT1B 4.629,1.446 4.869,1.602 0.240,0.156 10 E2 4.639,4.085 4.870,4.241 0.231,0.156 10 E2 3.875,6.128 4.612,6.298 0.737,0.170 10 *: Shielded 2.044,0.821 2.700,0.977 0.656,0.156 10 EFI NO. 2 1.465,1.706 2.573,1.893 1.108,0.187 10 Integration Relay 1.303,1.384 2.415,1.628 1.112,0.244 10 EFI MAIN NO. 1 0.67,0.797 1.446,1.177 0.776,0.379 10 EFI MAIN NO. 1 2.747,0.467 2.898,0.666 0.151,0.199 10 1 2.789,1.334 2.903,1.490 0.114,0.156 10 8 0.947,1.33 1.089,1.539 0.142,0.209 10 4 0.449,1.331 0.564,1.487 0.114,0.156 10 1 2.697,0.655 2.945,0.846 0.248,0.191 10 1S 2.655,1.507 2.941,1.689 0.286,0.182 10 1S 0.978,1.504 1.260,1.697 0.281,0.193 10 1S 0.494,1.508 0.792,1.705 0.298,0.197 10 1X 0.867,5.344 1.425,5.554 0.557,0.210 10 Battery 5.187,1.386 5.314,1.523 0.126,0.137 10 * 5.129,3.988 5.255,4.124 0.126,0.137 10 * 0.69,3.42 1.172,3.596 0.482,0.177 10 P/I-B


CONFIRMATION DRIVING PATTERN

A200170E14
2.707,2.371 2.918,2.559 0.211,0.188 10 [B] 4.133,0.731 4.349,0.919 0.216,0.188 10 [C] 5.074,3.102 5.297,3.295 0.223,0.193 10 [D] 1.04,0.498 2.441,0.681 1.401,0.184 10 120 km/h 1.092,1.374 2.359,1.558 1.267,0.184 10 60 km/h 1.274,2.224 1.673,2.388 0.399,0.165 10 Idling 0.477,2.459 1.672,2.618 1.195,0.160 10 Ignition Switch ON 2.426,3.135 3.235,3.319 0.809,0.184 10 Warming up 3.606,3.199 4.845,3.337 1.239,0.137 10 10 minutes or more 2.074,2.569 2.285,2.758 0.211,0.188 10 [A]

1.

Connect the GTS to the DLC3.

2.

Clear the DTCs.

3.

Turn the ignition switch off.

4.

Turn the ignition switch to ON and turn the GTS on (Step "A").

5.

Warm-up the engine until the engine coolant temperature is 75°C (167°F) or more (Step "B").

6.

With the transmission in 4th gear or more, drive the vehicle at 60 to 120 km/h (37 to 75 mph) for 10 minutes or more (Step "C").

7.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

8.

Input DTCs: P0136, P0137, P0138, P0156, P0157 and P0158.

9.

Check the DTC judgment result (Step "D").

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


10.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, perform the driving pattern adding the vehicle speed and using the second gear to decelerate the vehicle.


CAUTION / NOTICE / HINT

HINT:

Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F Sensor function provided in the Active Test. The Control the Injection Volume for air fuel ratio sensor function can help to determine whether the air fuel ratio sensor, heated oxygen sensor and other potential trouble areas are malfunctioning.

The following instructions describe how to conduct the Control the Injection Volume for A/F Sensor operation using the GTS.

1.

Connect the GTS to the DLC3.

2.

Start the engine and turn the GTS on.

3.

Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.

4.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.

5.

Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).

6.

Monitor the output voltages of the air fuel ratio sensor and heated oxygen sensor (AFS Voltage B1S1 and O2S B1S2, or AFS Voltage B2S1 and O2S B2S2) displayed on the GTS.



HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

Each sensor reacts in accordance with increases and decreases in the fuel injection volume.



GTS Display (Sensor) Injection Volume Status Voltage
AFS Voltage B1S1 or AFS Voltage B2S1
(Air fuel ratio sensor)
+12.5% Rich Below 3.1 V
AFS Voltage B1S1 or AFS Voltage B2S1
(Air fuel ratio sensor)
-12.5% Lean Higher than 3.4 V
O2S B1S2 or O2S B2S2
(Heated oxygen sensor)
+12.5% Rich Higher than 0.55 V
O2S B1S2 or O2S B2S2
(Heated oxygen sensor)
-12.5% Lean Below 0.4 V

NOTICE:

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.


·
A283583E52
5.792,3.594 7.115,3.865 1.323,0.271 10 false - Air fuel ratio sensor 3.823,4.927 4.531,5.104 0.708,0.177 8 false Below 0.4 V 3.208,4.396 4.333,4.615 1.125,0.219 10 false Output Voltage 3.25,3.365 4.542,3.615 1.292,0.25 10 false Injection Volume 3.229,1.292 4.521,1.542 1.292,0.25 10 false Injection Volume 3.24,2.313 4.333,2.521 1.094,0.208 10 false Output Voltage 0.625,1.292 1.917,1.542 1.292,0.25 10 false Injection Volume 0.625,3.365 1.917,3.615 1.292,0.25 10 false Injection Volume 0.594,5.438 1.885,5.688 1.292,0.25 10 false Injection Volume 0.604,7.49 1.896,7.74 1.292,0.25 10 false Injection Volume 3.25,7.49 4.542,7.74 1.292,0.25 10 false Injection Volume 3.25,5.438 4.542,5.688 1.292,0.25 10 false Injection Volume 0.635,2.302 1.823,2.51 1.188,0.208 10 false Output Voltage 0.625,4.396 1.792,4.646 1.167,0.25 10 false Output Voltage 0.552,6.479 1.719,6.729 1.167,0.25 10 false Output Voltage 0.573,8.563 1.74,8.813 1.167,0.25 10 false Output Voltage 3.24,8.563 4.406,8.813 1.167,0.25 10 false Output Voltage 3.25,6.479 4.417,6.729 1.167,0.25 10 false Output Voltage 3.51,4.698 4.542,4.885 1.031,0.188 8 false Higher than 0.55 V 0.927,2.646 1.958,2.833 1.031,0.188 8 false Higher than 3.4 V 1.177,2.885 1.927,3.073 0.75,0.188 8 false Below 3.1 V 1.469,1.604 1.917,1.792 0.448,0.188 8 false +12.5% 1.49,1.833 1.917,2.01 0.427,0.177 8 false -12.5% 3.5,2.604 4.531,2.792 1.031,0.188 8 false Higher than 0.55 V 3.813,2.844 4.521,3.021 0.708,0.177 8 false Below 0.4 V 0.844,4.802 2.042,5.052 1.198,0.25 8 false Almost no reaction 0.854,8.938 2.052,9.188 1.198,0.25 8 false Almost no reaction 3.5,8.938 4.698,9.188 1.198,0.25 8 false Almost no reaction 3.49,6.865 4.688,7.115 1.198,0.25 8 false Almost no reaction 0.917,6.771 1.948,6.958 1.031,0.188 8 false Higher than 3.4 V 1.167,7.021 1.917,7.208 0.75,0.188 8 false Below 3.1 V 0.24,2.083 0.396,2.281 0.156,0.198 10 false 1 0.24,4.25 0.396,4.448 0.156,0.198 10 false 2 0.25,6.333 0.406,6.531 0.156,0.198 10 false 3 0.24,8.417 0.396,8.615 0.156,0.198 10 false 4 0.115,0.49 0.49,0.719 0.375,0.229 10 false Case 0.813,0.448 2.844,0.844 2.031,0.396 10 false Air Fuel Ratio Sensor (Sensor 1) Output Voltage 3.375,0.469 5.531,0.875 2.156,0.406 10 false Heated Oxygen Sensor (Sensor 2) Output Voltage 5.938,0.469 6.979,0.885 1.042,0.417 10 false Main Suspected Trouble Area 6.396,2.115 6.552,2.313 0.156,0.198 10 false - 5.802,4 7.125,4.438 1.323,0.438 10 false - Air fuel ratio sensor heater 5.802,4.635 7.125,5.073 1.323,0.438 10 false - Air fuel ratio sensor circuit 5.844,5.51 6.896,5.885 1.052,0.375 10 false - Heated oxygen sensor 5.844,6.135 6.885,6.563 1.042,0.427 10 false - Heated oxygen sensor heater 5.844,6.75 6.885,7.188 1.042,0.438 10 false - Heated oxygen sensor circuit 5.823,7.51 6.708,7.917 0.885,0.406 10 false - Fuel injector assembly 5.813,8.063 6.969,8.396 1.156,0.333 10 false - Fuel pressure 5.802,8.375 7.094,9.083 1.292,0.708 10 false - Gas leakage from exhaust system (Air fuel ratio extremely rich or lean) 2.552,2.75 3,2.938 0.448,0.188 8 false OK 2.5,4.719 2.948,4.906 0.448,0.188 8 false NG 2.552,6.865 3,7.052 0.448,0.188 8 false OK 2.5,8.844 2.948,9.031 0.448,0.188 8 false NG 5.167,2.708 5.615,2.896 0.448,0.188 8 false OK 5.167,4.813 5.615,5 0.448,0.188 8 false OK 5.135,8.854 5.583,9.042 0.448,0.188 8 false NG 5.135,6.771 5.583,6.958 0.448,0.188 8 false NG 1.417,3.677 1.865,3.865 0.448,0.188 8 false +12.5% 4.01,1.594 4.458,1.781 0.448,0.188 8 false +12.5% 4,3.667 4.448,3.854 0.448,0.188 8 false +12.5% 1.427,3.875 1.854,4.052 0.427,0.177 8 false -12.5% 4.021,1.823 4.448,2 0.427,0.177 8 false -12.5% 4.021,3.896 4.448,4.073 0.427,0.177 8 false -12.5% 1.406,5.75 1.854,5.938 0.448,0.188 8 false +12.5% 1.375,7.771 1.823,7.958 0.448,0.188 8 false +12.5% 4.031,7.792 4.479,7.979 0.448,0.188 8 false +12.5% 4.073,5.729 4.521,5.917 0.448,0.188 8 false +12.5% 1.406,5.948 1.833,6.125 0.427,0.177 8 false -12.5% 1.396,8.01 1.823,8.188 0.427,0.177 8 false -12.5% 4.031,8.021 4.458,8.198 0.427,0.177 8 false -12.5% 4.083,5.938 4.51,6.115 0.427,0.177 8 false -12.5%

·

Following the Control the Injection Volume for A/F Sensor procedure enables technicians to check and graph the voltage outputs of both the air fuel ratio sensor and heated oxygen sensors.

·

To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / Data List / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ OUTPUT DTC (DTC P0136, P0137, P0138, P0156, P0157 OR P0158)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read DTCs.

Result
Result Proceed to
P0138 or P0158 A
P0137 or P0157 B
P0136 or P0156 C
P0136, P0137, P0138, P0156, P0157 or P0158 and other DTCs are output D



A

2.READ VALUE USING GTS (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR)

B

9.CHECK FOR EXHAUST GAS LEAK

C

7.PERFORM ACTIVE TEST USING GTS (INJECTION VOLUME)

D

2.READ VALUE USING GTS (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / O2S B1S2 or O2S B2S2.


e.

Allow the engine to idle.


f.

Read the heated oxygen sensor output voltage while idling.

Result
Result Proceed to
Higher than 1.0 V A
Below 1.0 V B



A

3.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT)

B

5.PERFORM ACTIVE TEST USING GTS (INJECTION VOLUME)
3.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT)
a.
A117841E98
0.109,0.074 0.288,0.244 0.179,0.170 10 *a 0.553,0.796 0.769,0.956 0.216,0.161 10 +B 2.524,2.486 3.073,2.637 0.549,0.151 10 OX1B*A 2.524,2.698 3.078,2.849 0.554,0.151 10 OX2B*B 2.524,0.796 3.059,0.952 0.536,0.156 10 HT1B*A 2.524,1.008 3.073,1.164 0.549,0.156 10 HT2B*B 0.553,2.687 0.764,2.847 0.211,0.161 10 E2 0.822,0.87 1.395,1.506 false 2.025,1.506 2.478,0.888 false 0.816,2.784 1.395,1.913 false 2.042,1.919 2.469,2.572 false

Disconnect the heated oxygen sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Bank 1 Sensor 2):
Tester Connection Condition Specified Condition
2 (+B) - 4 (E2) 20°C (68°F) 10 kΩ or higher
2 (+B) - 3 (OX1B) Always 10 kΩ or higher


Standard Resistance (Bank 2 Sensor 2):
Tester Connection Condition Specified Condition
2 (+B) - 4 (E2) 20°C (68°F) 10 kΩ or higher
2 (+B) - 3 (OX2B) Always 10 kΩ or higher


Text in Illustration
*A for Bank 1
*B for Bank 2
*a Component without harness connected
(Heated Oxygen Sensor)


c.

Reconnect the heated oxygen sensor connector.



OK

4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)

NG

4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)
a.

Disconnect the heated oxygen sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C45-45 (HT1B) - C45-114 (OX1B) Always 10 kΩ or higher
C45-44 (HT2B) - C45-112 (OX2B) Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
C46-45 (HT1B) - C46-114 (OX1B) Always 10 kΩ or higher
C46-44 (HT2B) - C46-112 (OX2B) Always 10 kΩ or higher



d.

Reconnect the heated oxygen sensor connector.


e.

Reconnect the ECM connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - HEATED OXYGEN SENSOR)

5.PERFORM ACTIVE TEST USING GTS (INJECTION VOLUME)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Warm up the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.


f.

Change the fuel injection volume using the GTS, and monitor the voltage output of the air fuel ratio sensor and heated oxygen sensor displayed on the GTS.

HINT:
·

Change the fuel injection volume within the range of -12.5% to +12.5%.

·

The air fuel ratio sensor is displayed as AFS Voltage B1S1 or AFS Voltage B2S1, and the heated oxygen sensor is displayed as O2S B1S2 or O2S B2S2 on the GTS.



Result
GTS Display (Sensor) Voltage Variation Proceed to
AFS Voltage B1S1
AFS Voltage B2S1
(Air fuel ratio sensor)
Alternates between higher than and below 3.3 V OK
Remains at higher than 3.3 V NG
Remains at below 3.3 V NG

HINT:

A normal heated oxygen sensor voltage (O2S B1S2 or O2S B2S2) reacts in accordance with increases and decreases in fuel injection volumes. When the air fuel ratio sensor voltage remains at either below or higher than 3.3 V despite the heated oxygen sensor indicating a normal reaction, the air fuel ratio sensor is malfunctioning.


A121606E83
5.885,2.479 6.365,1.396 false 5.552,2.271 6.365,1.396 false 5.708,1.667 6.365,1.396 false 5.563,2.448 5.844,2.667 false 3.021,1.26 2.865,1.677 false 4.396,1.865 4.094,1.698 false 3.573,2.625 3.188,2.938 false 1.958,1.99 2.125,1.99 false 1.958,2.948 2.156,2.948 false 1.531,1.896 1.906,2.052 0.375,0.156 10 false 3.3 V 2.656,0.26 3.292,0.458 0.635,0.198 10 false +12.5% 4.125,1.125 4.594,1.323 0.469,0.198 10 false -12.5% 1.656,2.854 1.906,3.052 0.25,0.198 10 false 1 V 1.667,3.385 1.906,3.583 0.24,0.198 10 false 0 V 3.073,1.146 3.833,1.344 0.76,0.198 10 false Malfunction 5.854,2.615 6.583,2.781 0.729,0.167 10 false Malfunction 4.76,0.125 5.823,0.323 1.063,0.198 10 false Injection Volume 3.635,2.51 5.563,2.729 1.927,0.219 10 false Heated Oxygen Sensor Output 6.406,1.125 6.938,1.813 0.531,0.688 10 false Air Fuel Ratio Sensor Output 4.406,1.792 4.927,2.104 0.521,0.313 10 true Normal



OK

6.CHECK AIR FUEL RATIO SENSOR

NG

15.REPLACE AIR FUEL RATIO SENSOR
6.CHECK AIR FUEL RATIO SENSOR
HINT:

This air fuel ratio sensor test is to check the air fuel ratio sensor current during the fuel-cut operation. When the sensor is normal, the sensor current will be below 3 mA in this test.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Clear.


e.

Clear DTCs.


f.

Drive the vehicle according to the driving pattern listed below:

i.

Warm up the engine.


ii.

Drive the vehicle at 60 km/h (40 mph) or more for 10 minutes or more.


iii.

Stop the vehicle.


iv.

Accelerate the vehicle to 60 km/h (40 mph) or more and then decelerate for 5 seconds or more. Repeat this process at least 3 times.

A152792E20
1.357,2.513 2.638,2.697 1.281,0.184 10 10 minutes or more 2.973,2.513 4.186,2.697 1.213,0.184 10 5 seconds or more 4.271,2.513 5.468,2.697 1.197,0.184 10 5 seconds or more 5.56,2.513 6.739,2.697 1.179,0.184 10 5 seconds or more 0.152,0.078 1.451,0.293 1.299,0.215 12 Driving Pattern: 0.348,1.224 1.006,1.602 0.658,0.378 10 60 km/h (40 mph) 0.348,2.055 0.884,2.415 0.536,0.360 10 0 km/h (0 mph)



g.

Enter the following menus: Powertrain / Engine and ECT / Data List / AFS Current B1S1 and AFS Current B2S1.


h.

Read the value of the air fuel ratio sensor current while the fuel-cut operation is being performed.

Standard current:

Below 2.2 mA


HINT:
·

To measure the air fuel ratio sensor current precisely, perform the fuel-cut operation as long as possible.

·

If it is difficult to measure the air fuel ratio sensor current, use the snapshot function of the GTS.




Result
Result Proceed to
Outside standard range A
Within standard range B


A

15.REPLACE AIR FUEL RATIO SENSOR

B

12.REPLACE HEATED OXYGEN SENSOR
7.PERFORM ACTIVE TEST USING GTS (INJECTION VOLUME)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Warm up the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / Data List / O2S B1S2 or O2S B2S2.


f.

Change the fuel injection volume using the GTS, monitoring the voltage output of the heated oxygen sensor displayed on the GTS.

HINT:
·

Change the fuel injection volume within the range of - 12.5% to +12.5%.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.



Standard voltage:

Fluctuates between 0.4 V or less and 0.55 V or higher.




OK

8.PERFORM ACTIVE TEST USING GTS (INJECTION VOLUME)

NG

9.CHECK FOR EXHAUST GAS LEAK
8.PERFORM ACTIVE TEST USING GTS (INJECTION VOLUME)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Warm up the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.


f.

Change the fuel injection volume using the GTS, and monitor the voltage output of the air fuel ratio sensor and heated oxygen sensor displayed on the GTS.

HINT:
·

Change the fuel injection volume within the range of -12.5% to +12.5%.

·

The air fuel ratio sensor is displayed as AFS Voltage B1S1 or AFS Voltage B2S1, and the heated oxygen sensor is displayed as O2S B1S2 or O2S B2S2 on the GTS.



Result
GTS Display (Sensor) Voltage Variation Proceed to
AFS Voltage B1S1
AFS Voltage B2S1
(Air fuel ratio sensor)
Alternates between higher than and below 3.3 V OK
Remains at higher than 3.3 V NG
Remains at below 3.3 V NG

HINT:

A normal heated oxygen sensor voltage (O2S B1S2 or O2S B2S2) reacts in accordance with increases and decreases in fuel injection volumes. When the air fuel ratio sensor voltage remains at either below or higher than 3.3 V despite the heated oxygen sensor indicating a normal reaction, the air fuel ratio sensor is malfunctioning.


A121606E83
5.885,2.479 6.365,1.396 false 5.552,2.271 6.365,1.396 false 5.708,1.667 6.365,1.396 false 5.563,2.448 5.844,2.667 false 3.021,1.26 2.865,1.677 false 4.396,1.865 4.094,1.698 false 3.573,2.625 3.188,2.938 false 1.958,1.99 2.125,1.99 false 1.958,2.948 2.156,2.948 false 1.531,1.896 1.906,2.052 0.375,0.156 10 false 3.3 V 2.656,0.26 3.292,0.458 0.635,0.198 10 false +12.5% 4.125,1.125 4.594,1.323 0.469,0.198 10 false -12.5% 1.656,2.854 1.906,3.052 0.25,0.198 10 false 1 V 1.667,3.385 1.906,3.583 0.24,0.198 10 false 0 V 3.073,1.146 3.833,1.344 0.76,0.198 10 false Malfunction 5.854,2.615 6.583,2.781 0.729,0.167 10 false Malfunction 4.76,0.125 5.823,0.323 1.063,0.198 10 false Injection Volume 3.635,2.51 5.563,2.729 1.927,0.219 10 false Heated Oxygen Sensor Output 6.406,1.125 6.938,1.813 0.531,0.688 10 false Air Fuel Ratio Sensor Output 4.406,1.792 4.927,2.104 0.521,0.313 10 true Normal



OK

CHECK EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO AND REPAIR CAUSE (FUEL INJECTOR, FUEL PRESSURE, GAS LEAK FROM SYSTEM, ETC.)

NG

15.REPLACE AIR FUEL RATIO SENSOR
9.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leakage.

OK:

No gas leak.




OK

10.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

NG

REPAIR OR REPLACE EXHAUST GAS LEAK POINT

10.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

OK

11.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

NG

11.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
a.

Disconnect the heated oxygen sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C20-1 (HT1B) - C45-45 (HT1B) Always Below 1 Ω
C20-3 (OX1B) - C45-114 (OX1B) Always Below 1 Ω
C20-4 (E2) - C45-115 (EX1B) Always Below 1 Ω
C21-1 (HT2B) - C45-44 (HT2B) Always Below 1 Ω
C21-3 (OX2B) - C45-112 (OX2B) Always Below 1 Ω
C21-4 (E2) - C45-113 (EX2B) Always Below 1 Ω
C20-1 (HT1B) or C45-45 (HT1B) - Body ground Always 10 kΩ or higher
C20-3 (OX1B) or C45-114 (OX1B) - Body ground Always 10 kΩ or higher
C20-4 (E2) or C45-115 (EX1B) - Body ground Always 10 kΩ or higher
C21-1 (HT2B) or C45-44 (HT2B) - Body ground Always 10 kΩ or higher
C21-3 (OX2B) or C45-112 (OX2B) - Body ground Always 10 kΩ or higher
C21-4 (E2) or C45-113 (EX2B) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
C20-1 (HT1B) - C46-45 (HT1B) Always Below 1 Ω
C20-3 (OX1B) - C46-114 (OX1B) Always Below 1 Ω
C20-4 (E2) - C46-115 (EX1B) Always Below 1 Ω
C21-1 (HT2B) - C46-44 (HT2B) Always Below 1 Ω
C21-3 (OX2B) - C46-112 (OX2B) Always Below 1 Ω
C21-4 (E2) - C46-113 (EX2B) Always Below 1 Ω
C20-1 (HT1B) or C46-45 (HT1B) - Body ground Always 10 kΩ or higher
C20-3 (OX1B) or C46-114 (OX1B) - Body ground Always 10 kΩ or higher
C20-4 (E2) or C46-115 (EX1B) - Body ground Always 10 kΩ or higher
C21-1 (HT2B) or C46-44 (HT2B) - Body ground Always 10 kΩ or higher
C21-3 (OX2B) or C46-112 (OX2B) - Body ground Always 10 kΩ or higher
C21-4 (E2) or C46-113 (EX2B) - Body ground Always 10 kΩ or higher



A137607E09
0.105,0.035 3.393,0.224 3.288,0.188 10 Reference (System Diagram of Bank 1 Sensor 2): 2.894,1.277 3.574,1.458 0.680,0.181 10 EFI NO. 2 0.992,1.299 2.014,1.457 1.022,0.159 10 EFI MAIN NO.1 1.938,2.405 2.960,2.564 1.022,0.159 10 EFI MAIN NO.1 1.02,3.33 1.500,3.512 0.480,0.181 10 Ground 3.393,0.367 4.889,0.548 1.496,0.181 10 Heated Oxygen Sensor 3.438,0.976 3.663,1.158 0.226,0.181 10 +B 4.587,0.976 4.967,1.158 0.380,0.181 10 HT1B 3.444,1.547 3.702,1.729 0.258,0.181 10 E2 4.6,1.547 5.025,1.729 0.424,0.181 10 OX1B 5.217,1.547 5.641,1.729 0.424,0.181 10 OX1B 5.217,2.149 5.641,2.331 0.424,0.181 10 EX1B 3.893,0.801 4.329,0.982 0.436,0.181 10 Heater 3.879,1.404 4.338,1.585 0.459,0.181 10 Sensor 5.883,0.325 6.208,0.506 0.326,0.181 10 ECM 5.21,0.969 5.590,1.151 0.380,0.181 10 HT1B 5.21,2.693 5.613,2.874 0.403,0.181 10 MREL 0.485,1.002 0.977,1.363 0.492,0.360 10 from Battery

d.

Reconnect the heated oxygen sensor connector.


e.

Reconnect the ECM connector.



OK

12.REPLACE HEATED OXYGEN SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - HEATED OXYGEN SENSOR)

12.REPLACE HEATED OXYGEN SENSOR
a.


NEXT

13.PERFORM CONFIRMATION DRIVING PATTERN
13.PERFORM CONFIRMATION DRIVING PATTERN
HINT:

Refer to Confirmation Driving Pattern.



NEXT

14.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137, P0138, P0156, P0157 OR P0158)
14.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137, P0138, P0156, P0157 OR P0158)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


e.

Input DTCs: P0136, P0137, P0138, P0156, P0157 and P0158.


f.

Check that the DTC monitor is NORMAL. If the DTC monitor is INCOMPLETE, perform the driving pattern again by accelerating the vehicle and using the second gear to decelerate the vehicle.

Result
Result Proceed to
NORMAL
(No DTC output)
A
ABNORMAL
(P0136, P0137, P0138, P0156, P0157 or P0158 stored)
B



A

END

B

15.REPLACE AIR FUEL RATIO SENSOR
a.


NEXT

16.PERFORM CONFIRMATION DRIVING PATTERN
16.PERFORM CONFIRMATION DRIVING PATTERN
HINT:

Refer to Confirmation Driving Pattern.



NEXT

17.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137, P0138, P0156, P0157 OR P0158)
17.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137, P0138, P0156, P0157 OR P0158)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


e.

Input DTCs: P0136, P0137, P0138, P0156, P0157 and P0158.


f.

Check that the DTC monitor is NORMAL. If the DTC monitor is INCOMPLETE, perform the driving pattern again by accelerating the vehicle and using the second gear to decelerate the vehicle.

Result
Result Proceed to
NORMAL
(No DTC output)
A
ABNORMAL
(P0136, P0137, P0138, P0156, P0157 or P0158 stored)
B



A

END

B