Home › Drivetrain › AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for 1VD-FTV) › from 2016.08
RM2660E _52 Drivetrain _052805 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0255265 AUTOMATIC TRANSMISSION SYSTEM(for 1VD-FTV) J

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1VD-FTV)  Transmission Control Switch Circuit  


DESCRIPTION

When moving the shift lever to S using the transmission control switch, it is possible to switch the shift range between "1" (1st range) and "6" (6th range).

Shifting to "+" once raises the shift range by one, and shifting to "-" lowers the shift range by one.

WIRING DIAGRAM

C176192E38
5.625,1.229 5.854,1.396 0.229,0.167 10 false 25 3.948,2.146 4.417,2.344 0.469,0.198 10 false SFTD 3.948,1.563 4.417,1.76 0.469,0.198 10 false SFTU 4.219,0.969 4.344,1.167 0.125,0.198 10 false S 3.063,0.969 3.302,1.167 0.24,0.198 10 false IG 3.063,2.146 3.302,2.344 0.24,0.198 10 false E 5.958,1.125 6.385,1.323 0.427,0.198 10 false S 5.615,1.813 5.844,1.979 0.229,0.167 10 false 38 5.938,1.698 6.365,1.896 0.427,0.198 10 false SW 5.625,2.406 5.854,2.573 0.229,0.167 10 false 37 5.948,2.25 6.375,2.448 0.427,0.198 10 false SFTD 2.802,2.729 3.229,2.927 0.427,0.198 10 false E52 2.802,2.917 4.583,3.115 1.781,0.198 10 false Transmission Control Switch 0.333,1.125 2.021,1.323 1.688,0.198 10 false from ECU-IG NO. 2 Fuse 2.833,1.229 3,1.396 0.167,0.167 10 false 3 2.844,2.406 3.031,2.573 0.188,0.167 10 false 5 4.396,1.229 4.76,1.396 0.365,0.167 10 false 7 4.396,1.813 4.677,1.979 0.281,0.167 10 false 2 4.396,2.396 4.719,2.563 0.323,0.167 10 false 1 0.083,2.969 0.875,3.167 0.792,0.198 10 false *1: for LHD 0.083,3.344 0.875,3.542 0.792,0.198 10 false *2: for RHD 6.073,3.354 6.458,3.552 0.385,0.198 10 false ECM 6.073,3.042 6.521,3.24 0.448,0.198 10 false A38*1 6.073,3.198 6.521,3.396 0.448,0.198 10 false A52*2

PROCEDURE

1.INSPECT TRANSMISSION CONTROL SWITCH
a.
C146679E41
1.625,1.292 0.948,1.042 true 0.958,1.844 1.635,1.594 true 1.802,1.292 2.646,1.042 true 2,1.333 2.677,1.333 true 2.646,1.844 1.969,1.594 true 0.052,0 2.583,0.365 2.531,0.365 10 false Component without harness connected: (Transmission Control Switch) 0.708,0.885 0.958,1.083 0.25,0.198 10 false IG 0.771,1.802 0.938,2 0.167,0.198 10 false S 2.719,0.906 3.229,1.104 0.51,0.198 10 false SFTU 2.719,1.24 3.229,1.438 0.51,0.198 10 false SFTD 2.719,1.792 2.896,1.99 0.177,0.198 10 false E

Disconnect the transmission control switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (IG) - 7 (S) Shift lever in S, "+" or "-" Below 1 Ω
2 (SFTU) - 5 (E) Shift lever held in "+"
(Up-shift)
Below 1 Ω
1 (SFTD) - 5 (E) Shift lever held in "-"
(Down-shift)
Below 1 Ω
3 (IG) - 7 (S) Shift lever not in S, "+" or "-" 10 kΩ or higher
2 (SFTU) - 5 (E) Shift lever in S 10 kΩ or higher
1 (SFTD) - 5 (E) Shift lever in S 10 kΩ or higher


Result:
Result Proceed to
OK A
NG (w/ Entry and Start System) B
NG (w/o Entry and Start System) C




A

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BATTERY, BODY GROUND)

B

REPLACE TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY)

C

REPLACE TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BATTERY, BODY GROUND)
a.
U164504E02
1.823,1.75 2.396,1.438 false 0.854,2.479 1.438,2.167 false 0.469,1.677 0.844,1.906 0.375,0.229 10 false E52 0.052,0.01 2.458,0.375 2.406,0.365 10 false Front view of wire harness connector: (to Transmission Control Switch) 0.688,2.406 0.885,2.604 0.198,0.198 10 false E 2.448,1.281 2.688,1.479 0.24,0.198 10 false IG

Disconnect the transmission control switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E52-3 (IG) - Body ground Ignition switch ON 11 to 14 V
E52-3 (IG) - Body ground Ignition switch off Below 1 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E52-5 (E) - Body ground Always Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)
a.
U164903E02
1.656,3.427 2.052,2.448 true 1.042,3.104 1.969,2.219 true 2.542,3.104 2.146,2.448 true 0.052,3.771 0.844,3.948 0.792,0.177 10 false *1: for LHD 0.052,4.198 0.844,4.375 0.792,0.177 10 false *2: for RHD 1.688,1.438 2.063,1.667 0.375,0.229 10 false A52 1.698,1.115 2.073,1.344 0.375,0.229 10 false A38 2.083,1.427 2.281,1.625 0.198,0.198 10 false *2 2.083,1.115 2.281,1.313 0.198,0.198 10 false *1 0.052,0.01 2.458,0.375 2.406,0.365 10 false Front view of wire harness connector: (to ECM) 0.802,3.125 1.281,3.323 0.479,0.198 10 false 25 (S) 1.302,3.458 1.99,3.656 0.688,0.198 10 false 37 (SFTD) 2.365,3.135 3.063,3.333 0.698,0.198 10 false 38 (SW)

Disconnect the ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
A38-25 (S) - Body ground
·

Ignition switch ON

·

Shift lever in S, "+" or "-"


11 to 14 V
A38-25 (S) - Body ground
·

Ignition switch ON

·

Shift lever not in S, "+" or "-"


Below 1 V

for RHD
Tester Connection Condition Specified Condition
A52-25 (S) - Body ground
·

Ignition switch ON

·

Shift lever in S, "+" or "-"


11 to 14 V
A52-25 (S) - Body ground
·

Ignition switch ON

·

Shift lever not in S, "+" or "-"


Below 1 V



c.

Turn the ignition switch off.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A38-38 (SW) - Body ground Shift lever held in "+"
(Up-shift)
Below 1 Ω
A38-37 (SFTD) - Body ground Shift lever held in "-"
(Down-shift)
Below 1 Ω
A38-38 (SW) - Body ground Shift lever in S 10 kΩ or higher
A38-37 (SFTD) - Body ground Shift lever in S 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
A52-38 (SW) - Body ground Shift lever held in "+"
(Up-shift)
Below 1 Ω
A52-37 (SFTD) - Body ground Shift lever held in "-"
(Down-shift)
Below 1 Ω
A52-38 (SW) - Body ground Shift lever in S 10 kΩ or higher
A52-37 (SFTD) - Body ground Shift lever in S 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR