Home › Engine / Hybrid System › CRUISE CONTROL › FORWARD RECOGNITION CAMERA SYSTEM › from 2015.08
RM2660E _51 Engine / Hybrid System _052804 CRUISE CONTROL _0255256 FORWARD RECOGNITION CAMERA SYSTEM C

CRUISE CONTROL  FORWARD RECOGNITION CAMERA SYSTEM  C1AAE  Heater Circuit  


DESCRIPTION

The forward recognition camera turns the forward recognition with heater hood sub-assembly on or off.

C1AAE is stored when the forward recognition camera detects a malfunction in the forward recognition with heater hood sub-assembly circuit.

DTC No. DTC Detection Condition Trouble Area
C1AAE
Either of the following conditions is met after 2 seconds have elapsed since the engine switch was turned on (IG):
·

Short to +B detected in the forward recognition with heater hood sub-assembly circuit for 1 second or more cumulatively

·

Open or short to ground detected in the forward recognition with heater hood sub-assembly circuit for 5 seconds or more


·

Forward recognition with heater hood sub-assembly

·

Forward recognition camera

·

Harness or connector



WIRING DIAGRAM

C368913E03
4.917,1.938 5.229,2.135 0.313,0.198 10 false R20 4.927,2.094 6.854,2.302 1.927,0.208 10 false Forward Recognition Camera 5.542,0.708 6,0.906 0.458,0.198 10 false HTR 5.333,0.552 5.792,0.75 0.458,0.198 10 false 1 3.188,1.021 5.052,1.427 1.865,0.406 10 false Forward Recognition with Heater Hood Sub-assembly 2.146,0.844 3.521,1.042 1.375,0.198 10 false ECU-IG NO. 3 0.531,0.698 2.823,0.896 2.292,0.198 10 false from IG Circuit 3.604,0.698 4.063,0.896 0.458,0.198 10 false IG1 4.125,0.698 4.583,0.896 0.458,0.198 10 false HTR 3.375,0.573 3.833,0.771 0.458,0.198 10 false 1 4.521,0.573 4.979,0.771 0.458,0.198 10 false 2 3.167,0.865 4.542,1.063 1.375,0.198 10 false R26 5.26,1.49 5.719,1.688 0.458,0.198 10 false 10 5.531,1.625 5.99,1.823 0.458,0.198 10 false GND

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera learning.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT



PROCEDURE

1.CHECK DTC OUTPUT (FORWARD RECOGNITION CAMERA SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / Front Recognition Camera / Trouble Codes.



f.

Make sure that the DTC detection conditions are met.

HINT:

If the conditions are not met, the system cannot detect the malfunction.

1.

Turn the engine switch on (IG) and wait 7 seconds or more.





Result:
Result Proceed to
DTC C1AAE is not output A
DTC C1AAE is output B



A

B

2.INSPECT FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY
2.INSPECT FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY
a.
C373924C03
1.333,2 1.5,2 1.5,2 1.885,1.354 true 2.583,2 2.417,2 2.417,2 2.052,1.354 true 0.083,0.083 0.396,0.281 0.313,0.198 10 false *a 1.031,1.938 1.49,2.135 0.458,0.198 10 false HTR 2.646,1.938 3.104,2.135 0.458,0.198 10 false IG1
*a Component without harness connected
(Forward Recognition with Heater Hood Sub-assembly)


Disconnect the R26 forward recognition with heater hood sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (IG1) - 2 (HTR) Always 38 to 42 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE (FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY POWER SOURCE VOLTAGE)

NG

REPLACE FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY

3.CHECK TERMINAL VOLTAGE (FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY POWER SOURCE VOLTAGE)
a.
C367313C15
1.5,0.25 1.927,0.5 0.427,0.25 1.167,1.667 1.333,1.667 1.333,1.667 1.615,1.313 true 1.604,0.302 2.76,0.521 1.156,0.219 10 false R26 0.906,1.583 1.219,1.781 0.313,0.198 10 false IG1 0.115,0.104 0.427,0.302 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Forward Recognition with Heater Hood Sub-assembly)


Disconnect the R26 forward recognition with heater hood sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R26-1(IG1) - Body ground Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY - FORWARD RECOGNITION CAMERA)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY - FORWARD RECOGNITION CAMERA)
a.

Disconnect the R20 forward recognition camera connector.


b.

Disconnect the R26 forward recognition with heater hood sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R20-1 (HTR) - R26-2 (HTR) Always Below 1 Ω
R20-1 (HTR) or R26-2 (HTR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION CAMERA - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION CAMERA - BODY GROUND)
a.

Disconnect the R20 forward recognition camera connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R20-10 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR