Home › Drivetrain › AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › TRANSMISSION WIRE › from 2017.08
RM2660E _52 Drivetrain _066407 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0323653 TRANSMISSION WIRE A

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  TRANSMISSION WIRE  INSTALLATION  


PROCEDURE

Hide 82125J 1.INSTALL TRANSMISSION WIRE

a.

Coat 2 new O-rings with ATF, and install them to the 2 temperature sensors.


b.

Coat a new O-ring with ATF, and install it to the transmission wire.


c.

Install the transmission wire to the automatic transmission case sub-assembly with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


d.

Connect the transmission wire connector.

HINT:

Push up the lever until the claw of the transmission wire connector makes a connection sound.



Hide 82125J 2.CONNECT TRANSMISSION WIRE

a.
U149047E03
2.188,1.229 2.292,0.521 2.292,0.521 2.427,0.521 true 2.104,1.24 1.927,0.531 1.927,0.531 1.813,0.531 true 1.198,2.438 1.51,3.031 1.51,3.031 1.656,3.031 true 1.115,2.302 0.781,2.979 0.781,2.979 0.677,2.979 true 2.448,0.438 2.604,0.615 0.156,0.177 10 false *1 1.615,0.438 1.771,0.615 0.156,0.177 10 false *2 1.688,2.938 1.844,3.115 0.156,0.177 10 false *1 0.469,2.938 0.625,3.115 0.156,0.177 10 false *2 2.594,1.167 2.729,1.323 0.135,0.156 10 false A 1.146,2.781 1.281,2.938 0.135,0.156 10 false B

Connect the 7 solenoid valve connectors.

Text in Illustration
*1 Temperature Sensor Clamp
*2 Temperature Sensor


b.

Install the 2 temperature sensors and 2 temperature sensor clamps to the transmission valve body assembly with the 2 bolts.

Torque:
for bolt A : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for bolt B : 11 N*m (112 kgf*cm, 8 ft.*lbf)


Hide 35106 3.INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

a.
U149048

Install the 4 transmission oil cleaner magnets to the automatic transmission oil pan sub-assembly as shown in the illustration.


b.

Install a new automatic transmission oil pan gasket to the automatic transmission oil pan sub-assembly.


c.
C157303E11
1.51,3.833 0.833,3.833 true 2.594,3.448 1.917,3.448 true 0.698,0.177 0.896,0.344 0.198,0.167 10 false *a 1.615,0.177 1.823,0.333 0.208,0.156 10 false *b 2.646,3.354 2.875,3.51 0.229,0.156 10 false *2 0.656,3.76 0.865,3.948 0.208,0.188 10 false *1 2.521,0.177 2.729,0.333 0.208,0.156 10 false *b 2.344,2.51 2.552,2.667 0.208,0.156 10 false *c

Install the automatic transmission oil pan sub-assembly with automatic transmission oil pan gasket to the automatic transmission case sub-assembly with the 10 bolts.

Torque:
7.4 N*m (75 kgf*cm, 65 in.*lbf)

Text in Illustration
*1 Sleeve
*2 Automatic Transmission Case Sub-assembly
*a Correct
*b Incorrect
*c Protrusion

NOTICE:
·

Make sure that the automatic transmission oil pan gasket seal surface and automatic transmission oil pan sub-assembly contact surface are free of oil and foreign matter.

·

Install the automatic transmission oil pan gasket so that there is no slack in the automatic transmission oil pan gasket, and the entire seal surface is level.

·

Make sure that the 8 protrusions are properly engaged to the automatic transmission oil pan sub-assembly.

·

When installing the automatic transmission oil pan sub-assembly, make sure that the automatic transmission oil pan gasket is not pinched between the sleeve and the seal surface of the automatic transmission case sub-assembly.