35104V
1.REMOVE BREATHER PLUG HOSE
Remove the breather plug hose from the automatic transmission case sub-assembly.
| *1 | Breather Plug Sub-assembly |
| *2 | Breather Plug Hose |
| *3 | Breather Plug |
| *4 | O-ring |
Remove the O-ring from the breather plug.
Remove the breather plug sub-assembly and breather plug from the breather plug hose.
89413N
2.REMOVE TRANSMISSION REVOLUTION SENSOR (NT)
89413R
3.REMOVE TRANSMISSION REVOLUTION SENSOR (SP2)
84540
4.REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
Using a screwdriver, bend the tabs of the lock washer.
Remove the nut and the lock washer.
Remove the bolt and park/neutral position switch assembly from the automatic transmission case sub-assembly.
Make sure that the manual valve lever shaft has not been rotated prior to installing the park/neutral position switch assembly as the detent spring may become detached from the manual valve lever shaft.
35104A
5.REMOVE REFILL PLUG
Remove the refill plug from the transfer adapter sub-assembly.
Remove the O-ring from the refill plug.
35104A
6.REMOVE AUTOMATIC TRANSMISSION CASE PLUG
Remove the 6 automatic transmission case plugs from the automatic transmission case sub-assembly.
Remove the 6 O-rings from the 6 automatic transmission case plugs.
Using a T55 "TORX" socket wrench, remove the automatic transmission case plug from the automatic transmission case sub-assembly.
Remove the O-ring from the automatic transmission case plug.
7.REMOVE OIL COOLER TUBE UNION
Remove the 2 oil cooler tube unions from the automatic transmission case sub-assembly.
Remove the 2 O-rings from the 2 oil cooler tube unions.
36117
8.REMOVE TRANSFER ADAPTER SUB-ASSEMBLY
Remove the 10 bolts and transfer adapter sub-assembly from the automatic transmission case sub-assembly.
Use a brass bar and hammer to remove the transfer adapter sub-assembly.
Remove the 2 straight pins from the transfer adapter sub-assembly.
It is not necessary to remove the straight pins they are being replaced.
36117A
9.REMOVE TRANSFER ADAPTER OIL SEAL
Using a screwdriver, pry out the transfer adapter oil seal from the transfer adapter sub-assembly.
| *a | Protective Tape |
Be careful not to damage the transfer adapter sub-assembly.
Tape the screwdriver tip before use.
35157B
10.REMOVE REAR TRANSFER CASE ADAPTER OIL RECEIVER
Using snap ring pliers, remove the snap ring and rear transfer case adapter oil receiver from the transfer adapter sub-assembly.
35111
11.REMOVE AUTOMATIC TRANSMISSION HOUSING
Remove the 12 bolts and automatic transmission housing from the automatic transmission case sub-assembly.
35104
12.SECURE AUTOMATIC TRANSMISSION CASE SUB-ASSEMBLY
Install the automatic transmission case sub-assembly to an overhaul attachment.
13.REMOVE OVERFLOW PLUG
Using a 5 mm socket hexagon wrench, remove the overflow plug and gasket.
14.REMOVE DRAIN PLUG
Remove the drain plug and gasket.
35106
15.REMOVE AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY
Do not turn the transmission over as this will contaminate the transmission valve body assembly with foreign matter located at the bottom of the automatic transmission oil pan sub-assembly.
Click hereDrivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>TRANSMISSION WIRE>REMOVAL
82125J
16.REMOVE TRANSMISSION WIRE
Remove the 2 bolts and 2 temperature sensor clamps, and disconnect the 2 temperature sensors.
| *1 | Temperature Sensor Clamp |
| *2 | Temperature Sensor |
Disconnect the 7 solenoid valve connectors and transmission wire from the transmission valve body assembly.
Remove the bolt and pull out the transmission wire from the automatic transmission case sub-assembly.
Remove the O-ring from the connector of transmission wire.
Remove the 2 O-rings from the 2 temperature sensors.
35330
17.REMOVE VALVE BODY OIL STRAINER ASSEMBLY
35410
18.REMOVE TRANSMISSION VALVE BODY ASSEMBLY
35145C
19.REMOVE TRANSMISSION CASE GASKET
35159
20.REMOVE BRAKE DRUM GASKET
Remove the 2 brake drum gaskets from the automatic transmission case sub-assembly.
35595
21.REMOVE PARKING LOCK PAWL BRACKET
Remove the 3 bolts and parking lock pawl bracket from the automatic transmission case sub-assembly.
35501
22.REMOVE PARKING LOCK ROD SUB-ASSEMBLY
Remove the parking lock rod sub-assembly from the manual valve lever sub-assembly.
35556
23.REMOVE PARKING LOCK PAWL SHAFT
Pull out the parking lock pawl shaft from the front side, and remove the parking lock pawl and spring.
| *1 | Parking Lock Pawl |
| *2 | E-ring |
| *3 | Parking Lock Pawl Shaft |
| *4 | Spring |
Remove the E-ring from the parking lock pawl shaft.
35505
24.REMOVE MANUAL VALVE LEVER SUB-ASSEMBLY
Using a screwdriver and hammer, cut off the spacer and remove it from the manual valve lever shaft.
| *a | Protective Tape |
Be careful not to damage the manual valve lever shaft.
Tape the screwdriver tip before use.
Using a 3 mm pin punch and hammer, drive out the spring pin.
Slowly drive out the spring pin so that it does not fall into the automatic transmission case sub-assembly.
Pull the manual valve lever shaft out through the case and remove the manual valve lever sub-assembly.
35506F
25.REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL
Using a screwdriver, pry out the 2 manual valve lever shaft oil seals from the automatic transmission case sub-assembly.
| *a | Protective Tape |
Be careful not to damage the automatic transmission case sub-assembly.
Tape the screwdriver tip before use.
26.REMOVE OIL PUMP ASSEMBLY
Remove the 10 bolts.
Using SST, pull out the oil pump assembly from the automatic transmission case sub-assembly.
| *a | Turn |
Remove the 2 thrust bearing races from the oil pump assembly.
| *1 | Thrust Bearing Race |
| *2 | Oil Pump O-ring |
Remove the oil pump O-ring from the oil pump assembly.
27.REMOVE DIRECT CLUTCH DRUM SUB-ASSEMBLY AND INPUT SHAFT ASSEMBLY
Remove the direct clutch drum sub-assembly and input shaft assembly from the automatic transmission case sub-assembly.
| *1 | Thrust Needle Roller Bearing |
Remove the 3 thrust needle roller bearings from the direct clutch drum sub-assembly and input shaft assembly.
35605A
28.REMOVE DIRECT CLUTCH DRUM SUB-ASSEMBLY
Remove the direct clutch drum sub-assembly from the input shaft sub-assembly.
| *1 | Direct Clutch Drum Sub-assembly |
| *2 | Input Shaft Sub-assembly |
35635
29.INSPECT CLEARANCE OF NO. 1 CLUTCH (FORWARD CLUTCH)
35617
30.REMOVE CLUTCH DRUM OIL SEAL RING
Remove the 3 clutch drum oil seal rings from the input shaft sub-assembly.
35633B
31.REMOVE NO. 1 CLUTCH DISC (FORWARD CLUTCH DISC)
Secure the input shaft sub-assembly in a vise between aluminum plates.
Do not overtighten the vise.
Using a screwdriver, remove the snap ring.
| *a | Protective Tape |
Be careful not to damage the input shaft sub-assembly.
Tape the screwdriver tip before use.
Remove the forward clutch flange, 5 No. 1 clutch discs and 5 No. 1 clutch plates from the input shaft sub-assembly.
| *1 | Forward Clutch Flange |
| *2 | No. 1 Clutch Disc |
| *3 | No. 1 Clutch Plate |
35633B
32.INSPECT NO. 1 CLUTCH DISC (FORWARD CLUTCH DISC)
35668
33.REMOVE NO. 1 CLUTCH BALANCER
Place SST on the No. 1 clutch balancer, and compress the forward clutch return spring sub-assembly with a press.
Using SST, remove the snap ring.
Remove the No. 1 clutch balancer and forward clutch return spring sub-assembly from the input shaft sub-assembly.
| *1 | No. 1 Clutch Balancer |
| *2 | Forward Clutch Return Spring Sub-assembly |
Remove the O-ring from the No. 1 clutch balancer.
35603A
34.INSPECT FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY
35612B
35.REMOVE FORWARD CLUTCH PISTON
While holding the forward clutch piston, apply compressed air to the oil hole of the input shaft sub-assembly to remove the forward clutch piston from the input shaft sub-assembly.
| *1 | Forward Clutch Piston |
| *a | Oil Hole |
Remove the O-ring from the forward clutch piston.
Remove the O-ring from the input shaft sub-assembly.
36.INSPECT INPUT SHAFT SUB-ASSEMBLY
35675C
37.INSPECT CLEARANCE OF NO. 2 CLUTCH (DIRECT CLUTCH)
35667A
38.REMOVE NO. 2 CLUTCH DISC (DIRECT CLUTCH DISC)
Using a screwdriver, remove the snap ring from the direct clutch drum sub-assembly.
| *a | Protective Tape |
Be careful not to damage the direct clutch drum sub-assembly.
Tape the screwdriver tip before use.
Remove the direct clutch flange, 5 No. 2 clutch discs and 5 No. 2 clutch plates from the direct clutch drum sub-assembly.
| *1 | Direct Clutch Flange |
| *2 | No. 2 Clutch Disc |
| *3 | No. 2 Clutch Plate |
35667A
39.INSPECT NO. 2 CLUTCH DISC (DIRECT CLUTCH DISC)
35669
40.REMOVE NO. 2 CLUTCH BALANCER
Place SST on the No. 2 clutch balancer, and compress the direct clutch return spring sub-assembly with a press.
Using SST, remove the snap ring.
Remove the No. 2 clutch balancer and direct clutch return spring sub-assembly from the direct clutch drum sub-assembly.
| *1 | No. 2 Clutch Balancer |
| *2 | Direct Clutch Return Spring Sub-assembly |
Remove the O-ring from the No. 2 clutch balancer.
35604
41.INSPECT DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY
35606A
42.REMOVE DIRECT CLUTCH PISTON
Place the oil pump assembly onto the torque converter assembly, and then place the direct clutch drum sub-assembly onto the oil pump assembly.
| *1 | Oil Pump Assembly |
| *2 | Torque Converter Assembly |
| *a | Oil Hole |
While holding the direct clutch piston, apply compressed air to the oil hole of the oil pump assembly to remove the direct clutch piston from the direct clutch drum sub-assembly.
Remove the 2 O-rings from the direct clutch piston.
35605A
43.INSPECT DIRECT CLUTCH DRUM SUB-ASSEMBLY
35631
44.REMOVE MULTIPLE DISC CLUTCH HUB
Remove the multiple disc clutch hub from the automatic transmission case sub-assembly.
| *1 | Thrust Bearing Race |
Remove the 2 thrust bearing races from the multiple disc clutch hub.
35061
45.REMOVE FORWARD CLUTCH HUB SUB-ASSEMBLY
Remove the forward clutch hub sub-assembly from the automatic transmission case sub-assembly.
| *1 | Thrust Needle Roller Bearing |
Remove the 2 thrust needle roller bearings from the forward clutch hub sub-assembly.
35061
46.INSPECT FORWARD CLUTCH HUB SUB-ASSEMBLY
35709J
47.REMOVE SUN GEAR INPUT DRUM SUB-ASSEMBLY
Remove the sun gear input drum sub-assembly from the automatic transmission case sub-assembly.
| *1 | Thrust Bearing Race |
| *2 | Thrust Needle Roller Bearing |
Remove the thrust needle roller bearing and thrust bearing race from the sun gear input drum sub-assembly.
35709J
48.INSPECT SUN GEAR INPUT DRUM SUB-ASSEMBLY
35720
49.REMOVE FRONT PLANETARY GEAR ASSEMBLY
Remove the front planetary gear assembly from the automatic transmission case sub-assembly.
| *1 | Thrust Bearing Race |
Remove the 2 thrust bearing races from the front planetary gear assembly
35720
50.INSPECT FRONT PLANETARY GEAR ASSEMBLY
35743
51.REMOVE FRONT PLANETARY RING GEAR WITH FRONT PLANETARY RING GEAR FLANGE SUB-ASSEMBLY
Remove the front planetary ring gear with front planetary ring gear flange sub-assembly from the automatic transmission case sub-assembly.
| *1 | Thrust Needle Roller Bearing |
| *2 | Thrust Bearing Race |
Remove the thrust needle roller bearing and thrust bearing race from the front planetary ring gear with front planetary ring gear flange sub-assembly.
35076C
52.REMOVE FRONT PLANETARY RING GEAR FLANGE SUB-ASSEMBLY
Using needle-nose pliers, remove the snap ring and front planetary ring gear flange sub-assembly from the front planetary ring gear.
| *1 | Front Planetary Ring Gear |
| *2 | Snap Ring |
| *3 | Front Planetary Ring Gear Flange Sub-assembly |
35076C
53.INSPECT FRONT PLANETARY RING GEAR FLANGE SUB-ASSEMBLY
35682A
54.INSPECT CLEARANCE OF NO. 2 BRAKE
35699
55.REMOVE NO. 2 BRAKE CYLINDER WITH NO.2 BRAKE PISTON
Place SST on the No. 2 brake cylinder, and compress the No. 2 brake piston return spring sub-assembly with a press.
| *a | Turn |
Using a screwdriver, remove the snap ring from the automatic transmission case sub-assembly.
Be careful not to damage the automatic transmission case sub-assembly.
Tape the screwdriver tip before use.
Remove the No. 2 brake cylinder with No. 2 brake piston and No. 2 brake piston return spring sub-assembly from the automatic transmission case sub-assembly.
| *1 | No. 2 Brake Cylinder with No. 2 Brake Piston |
| *2 | No. 2 Brake Piston Return Spring Sub-assembly |
35045
56.INSPECT NO. 2 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY
35622G
57.REMOVE NO. 2 BRAKE PISTON
While holding the No. 2 brake piston, apply compressed air to the oil hole of the No. 2 brake cylinder to remove the No. 2 brake piston from the No. 2 brake cylinder.
Remove the 2 O-rings from the No. 2 brake piston
35682A
58.REMOVE NO. 2 BRAKE DISC
Remove the 2 No. 2 brake flanges, 5 No. 2 brake discs and 4 No. 2 brake plates from the automatic transmission case sub-assembly.
| *1 | No. 2 Brake Flange |
| *2 | No. 2 Brake Disc |
| *3 | No. 2 Brake Plate |
35682A
59.INSPECT NO. 2 BRAKE DISC
35769
60.REMOVE CENTER PLANETARY RING GEAR FLANGE WITH CENTER PLANETARY RING GEAR
Remove the center planetary ring gear flange with center planetary ring gear from the automatic transmission case sub-assembly.
| *1 | Thrust Needle Roller Bearing |
Remove the 2 thrust needle roller bearings from the center planetary ring gear flange with center planetary ring gear.
35763
61.REMOVE CENTER PLANETARY RING GEAR
Using a screwdriver, remove the snap ring from the center planetary ring gear flange with center planetary ring gear.
| *a | Protective Tape |
Be careful not to damage the center planetary ring gear flange with center planetary ring gear.
Tape the screwdriver tip before use.
Remove the center planetary ring gear from the center planetary ring gear flange.
| *1 | Center Planetary Ring Gear Flange |
| *2 | Center Planetary Ring Gear |
35750
62.REMOVE CENTER PLANETARY GEAR ASSEMBLY
Remove the center planetary gear assembly from the automatic transmission case sub-assembly.
| *1 | Thrust Bearing Race |
Remove the thrust bearing race from the center planetary gear assembly.
35750
63.INSPECT CENTER PLANETARY GEAR ASSEMBLY
35719B
64.REMOVE PLANETARY SUN GEAR
Remove the planetary sun gear from the automatic transmission case sub-assembly.
35681A
65.INSPECT CLEARANCE OF NO. 1 BRAKE
35681A
66.REMOVE NO. 1 BRAKE DISC
Using a screwdriver, remove the snap ring from the automatic transmission case sub-assembly.
| *a | Protective Tape |
Be careful not to damage the automatic transmission case sub-assembly.
Tape the screwdriver tip before use.
Remove the No. 1 brake flange, 4 No. 1 brake discs and 4 No. 1 brake plates from the automatic transmission case sub-assembly.
| *1 | No. 1 Brake Flange |
| *2 | No. 1 Brake Disc |
| *3 | No. 1 Brake Plate |
35681A
67.INSPECT NO. 1 BRAKE DISC
35698
68.REMOVE NO. 1 BRAKE CYLINDER WITH NO. 1 BRAKE PISTON
Place SST on the No. 1 brake piston return spring sub-assembly, and compress the No. 1 brake piston return spring sub-assembly with a press.
| *a | Turn |
Using a screwdriver, remove the snap ring from the automatic transmission case sub-assembly.
Be careful not to damage the automatic transmission case sub-assembly.
Tape the screwdriver tip before use.
Remove the No. 1 brake piston return spring sub-assembly and No. 1 brake cylinder with No. 1 brake piston from the automatic transmission case sub-assembly.
| *1 | No. 1 Brake Piston Return Spring Sub-assembly |
| *2 | No. 1 Brake Cylinder with No. 1 Brake Piston |
35608J
69.INSPECT NO. 1 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY
35621V
70.REMOVE NO. 1 BRAKE PISTON
While holding the No. 1 brake piston, apply compressed air to the oil hole of the No. 1 brake cylinder to remove the No. 1 brake piston from the No. 1 brake cylinder.
Remove the 2 O-rings from the No. 1 brake piston.
35684
71.INSPECT CLEARANCE OF NO. 4 BRAKE
35713
72.REMOVE INTERMEDIATE SHAFT WITH NO. 3 ONE-WAY CLUTCH ASSEMBLY AND REAR PLANETARY RING GEAR
Using SST, remove the snap ring from the automatic transmission case sub-assembly.
Remove the intermediate shaft with No. 3 one-way clutch assembly and rear planetary ring gear from the automatic transmission case sub-assembly.
35770C
73.INSPECT NO. 3 ONE-WAY CLUTCH ASSEMBLY
35770C
74.REMOVE NO. 3 ONE-WAY CLUTCH ASSEMBLY WITH ONE-WAY CLUTCH INNER RACE
Remove the No. 3 one-way clutch assembly with one-way clutch inner race from the intermediate shaft with rear planetary ring gear.
| *1 | No. 3 One-way Clutch Assembly with One-way Clutch Inner Race |
| *2 | Intermediate Shaft with Rear Planetary Ring gear |
35797B
75.REMOVE ONE-WAY CLUTCH INNER RACE
Remove the one-way clutch inner race from the No. 3 one-way clutch assembly.
| *1 | One-way Clutch Inner Race |
| *2 | No. 3 One-way Clutch Assembly |
35077D
76.REMOVE REAR PLANETARY RING GEAR FLANGE SUB-ASSEMBLY WITH REAR PLANETARY RING GEAR
Remove the rear planetary ring gear flange sub-assembly with rear planetary ring gear from the intermediate shaft.
| *1 | Rear Planetary Ring Gear Flange Sub-assembly with Rear Planetary Ring Gear |
| *2 | Thrust Bearing Race |
Remove the thrust bearing race from the rear planetary ring gear flange sub-assembly with rear planetary ring gear.
Remove the thrust needle roller bearing and thrust bearing race from the intermediate shaft.
| *1 | Thrust Needle Roller Bearing |
| *2 | Thrust Bearing Race |
35077D
77.INSPECT REAR PLANETARY RING GEAR FLANGE SUB-ASSEMBLY
35713
78.INSPECT INTERMEDIATE SHAFT
35761
79.REMOVE REAR PLANETARY RING GEAR
Using a screwdriver, remove the snap ring from the rear planetary ring gear flange sub-assembly with rear planetary ring gear.
| *a | Protective Tape |
Be careful not to damage the rear planetary ring gear flange sub-assembly with rear planetary ring gear.
Tape the screwdriver tip before use.
Remove the rear planetary ring gear from the rear planetary ring gear flange sub-assembly.
| *1 | Rear Planetary Ring Gear Flange Sub-assembly |
| *2 | Rear Planetary Ring Gear |
35760
80.REMOVE REAR PLANETARY GEAR ASSEMBLY WITH NO. 4 BRAKE DISC
Remove the rear planetary gear assembly with No. 4 brake disc from the automatic transmission case sub-assembly.
| *1 | Thrust Needle Roller Bearing |
| *2 | Thrust Bearing Race |
Remove the 2 thrust needle roller bearings and thrust bearing race from the rear planetary gear assembly with No. 4 brake disc.
Remove the thrust bearing race from the automatic transmission case sub-assembly.
35760
81.INSPECT REAR PLANETARY GEAR ASSEMBLY
35684
82.REMOVE NO. 4 BRAKE DISC
Remove the No. 4 brake flange, 7 No. 4 brake discs and 6 No. 4 brake plates from the rear planetary gear assembly.
| *1 | No. 4 Brake Flange |
| *2 | No. 4 Brake Disc |
| *3 | No. 4 Brake Plate |
Remove the No. 4 brake flange from the automatic transmission case sub-assembly.
35684
83.INSPECT NO. 4 BRAKE DISC
35623H
84.REMOVE 1ST AND REVERSE BRAKE PISTON
Place SST on the 1st and reverse brake return spring sub-assembly and compress the 1st and reverse brake return spring sub-assembly.
Using SST, remove the snap ring from the automatic transmission case sub-assembly.
Remove the 1st and reverse brake return spring sub-assembly from the automatic transmission case sub-assembly.
Apply compressed air to the oil hole of the automatic transmission case sub-assembly to remove the 1st and reverse brake piston from the automatic transmission case sub-assembly.
Remove the O-ring from the 1st and reverse brake piston.
35068
85.INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY
35626
86.REMOVE BRAKE REACTION SLEEVE
Using SST, remove the brake reaction sleeve from the automatic transmission case sub-assembly.
Remove the 2 O-rings from the brake reaction sleeve.
35629A
87.REMOVE NO. 4 BRAKE PISTON
Using SST, remove the No. 4 brake piston from the automatic transmission case sub-assembly.
Remove the 2 O-rings from the No. 4 brake piston.
35639B
88.REMOVE BRAKE PLATE STOPPER SPRING
Remove the 2 brake plate stopper springs from the automatic transmission case sub-assembly.