Home › Drivetrain › AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE) › from 2017.08
RM2660E _52 Drivetrain _066407 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0327282 AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE) J

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE)  Transmission Control Switch Circuit  


DESCRIPTION

After moving the shift lever to S, it is possible to switch the shift range between "1" (S1 range) and "6" (S6 range) using the transmission control switch.

Moving the shift lever to "+" once raises the shift range by one, and moving the shift lever to "-" once lowers the shift range by one.

WIRING DIAGRAM

C311455E90
0.323,1.75 1.969,2.208 1.646,0.458 10 false from ECU-IG NO. 2 Fuse 3.615,2.208 4.229,2.406 0.615,0.198 10 false SFTU 3.615,2.802 4.229,3 0.615,0.198 10 false SFTD 3.865,1.625 4.479,1.823 0.615,0.198 10 false S 5.198,1.615 5.813,1.813 0.615,0.198 10 false S 5.188,2.208 5.802,2.406 0.615,0.198 10 false SFTU 5.188,2.781 5.802,2.979 0.615,0.198 10 false SFTD 2.479,3.427 3.094,3.625 0.615,0.198 10 false E52 2.479,3.604 4.646,4.104 2.167,0.5 10 false Transmission Control Switch 5.604,3.865 6.219,4.063 0.615,0.198 10 false A38 5.604,4.042 6.104,4.365 0.5,0.323 10 false ECM 2.76,1.625 3.375,1.823 0.615,0.198 10 false IG 2.75,2.219 3.365,2.417 0.615,0.198 10 false E 2.542,1.635 2.854,1.833 0.313,0.198 10 false 3 2.531,2.208 2.844,2.406 0.313,0.198 10 false 5 4.906,2.802 5.219,3 0.313,0.198 10 false 47 4.906,2.208 5.219,2.406 0.313,0.198 10 false 39 4.906,1.625 5.219,1.823 0.313,0.198 10 false 27 4.094,1.625 4.406,1.823 0.313,0.198 10 false 7 4.104,2.198 4.417,2.396 0.313,0.198 10 false 2 4.094,2.792 4.406,2.99 0.313,0.198 10 false 1 6.021,2.063 6.479,2.26 0.458,0.198 10 false 12 V 6.021,2.646 6.479,2.844 0.458,0.198 10 false 12 V

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.READ VALUE USING GTS (SPORTS MODE SELECTION SW)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

In accordance with the display on the GTS, read the Data List.

Engine and ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Sports Mode Selection SW Sport mode select switch status/
ON or OFF
·

ON: Shift lever in S, "+" or "-"

·

OFF: Shift lever not in S, "+" or "-"


-


Result
Result Proceed to
Data display is within Normal Condition range A
Data display is not within Normal Condition range B


A

2.READ VALUE USING GTS (SPORTS SHIFT UP SW AND SPORTS SHIFT DOWN SW)

B

6.INSPECT TRANSMISSION CONTROL SWITCH (LOWER SHIFT LEVER ASSEMBLY)
2.READ VALUE USING GTS (SPORTS SHIFT UP SW AND SPORTS SHIFT DOWN SW)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

In accordance with the display on the GTS, read the Data List.

Engine and ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Sports Shift Up SW Sport shift up switch status/
ON or OFF
·

ON: Shift lever held in "+" (up-shift)

·

OFF: Shift lever not held in "+" (up-shift)


-
Sports Shift Down SW Sport shift down switch status/
ON or OFF
·

ON: Shift lever held in "-" (down-shift)

·

OFF: Shift lever not held in "-" (down-shift)


-


Result
Result Proceed to
Data display is within Normal Condition range A
Data display is not within Normal Condition range B


A

B

3.INSPECT TRANSMISSION CONTROL SWITCH (LOWER SHIFT LEVER ASSEMBLY)
3.INSPECT TRANSMISSION CONTROL SWITCH (LOWER SHIFT LEVER ASSEMBLY)
a.
C203344E51
1.802,0.75 2.135,0.188 false 1.938,0.74 2.521,0.521 false 2.594,1.302 1.948,1 false 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 2.188,0.094 2.698,0.292 0.51,0.198 10 false SFTU 2.573,0.438 3.083,0.635 0.51,0.198 10 false SFTD 2.667,1.229 2.844,1.427 0.177,0.198 10 false E

Disconnect the transmission control switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (SFTU) - 5 (E) Shift lever held in "+"
(Up-shift)
Below 1 Ω
1 (SFTD) - 5 (E) Shift lever held in "-"
(Down-shift)
Below 1 Ω
2 (SFTU) - 5 (E) Shift lever not held in "+" 10 kΩ or higher
1 (SFTD) - 5 (E) Shift lever not held in "-" 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Transmission Control Switch)



OK

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BODY GROUND)

NG

REPLACE TRANSMISSION CONTROL SWITCH (LOWER SHIFT LEVER ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BODY GROUND)
a.
U148281E06
1.083,1.719 1.479,1.406 false 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 0.542,1 0.917,1.229 0.375,0.229 10 false E52 0.948,1.667 1.104,1.865 0.156,0.198 10 false E

Disconnect the transmission control switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E52-5 (E) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Transmission Control Switch)



OK

5.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)
a.
U164948E03
1.792,1.698 2.177,1.26 true 2.615,1.698 2.177,1.188 true 0.063,0 0.375,0.198 0.313,0.198 10 false *a 1.396,1.719 2.115,1.917 0.719,0.198 10 false 47 (SFTD) 2.427,1.719 3.146,1.917 0.719,0.198 10 false 39 (SFTU) 1.688,0.292 2.063,0.521 0.375,0.229 10 false A38

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A38-39 (SFTU) - Body ground Shift lever held in "+"
(Up-shift)
Below 1 Ω
A38-47 (SFTD) - Body ground Shift lever held in "-"
(Down-shift)
Below 1 Ω
A38-39 (SFTU) - Body ground Shift lever not held in "+" 10 kΩ or higher
A38-47 (SFTD) - Body ground Shift lever not held in "-" 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT TRANSMISSION CONTROL SWITCH (LOWER SHIFT LEVER ASSEMBLY)
a.
C203344E52
1.656,0.74 1.125,0.302 false 1.125,1.438 1.656,1.01 false 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 0.896,0.198 1.135,0.396 0.24,0.198 10 false IG 0.958,1.344 1.146,1.542 0.188,0.198 10 false S

Disconnect the transmission control switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (IG) - 7 (S) Shift lever in S, "+" or "- " Below 1 Ω
3 (IG) - 7 (S) Shift lever not in S, "+" or "-" 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Transmission Control Switch)



OK

7.CHECK HARNESS AND CONNECTOR (BATTERY - TRANSMISSION CONTROL SWITCH)

NG

REPLACE TRANSMISSION CONTROL SWITCH (LOWER SHIFT LEVER ASSEMBLY)

7.CHECK HARNESS AND CONNECTOR (BATTERY - TRANSMISSION CONTROL SWITCH)
a.
U148282E06
1.802,1.063 2.344,0.75 false 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 2.406,0.646 2.719,0.844 0.313,0.198 10 false IG 0.531,1 0.906,1.229 0.375,0.229 10 false E52

Disconnect the transmission control switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E52-3 (IG) - Body ground Engine switch on (IG) 11 to 14 V
E52-3 (IG) - Body ground Engine switch off Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Transmission Control Switch)



OK

8.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)
a.

Disconnect the transmission control switch connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E52-7 (S) - A38-27 (S) Always Below 1 Ω
E52-7 (S) - Body ground Always 10 kΩ or higher
A38-27 (S) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR